Dave
Sun Mar 02 10:29:05 PST 2008
The repair install isn't guaranteed to cover all situations of hardware
replacement. I'd backup and start a clean installation.
To do a clean install, either boot the Windows 2000 install CD-Rom or setup
disks. The set of four install disks can be created from your Windows 2000
CD-Rom; change to the \bootdisk directory on the CD-Rom and execute
makeboot.exe (from dos) or makebt32.exe (from 32 bit) and follow the
prompts.
(Note: If your drive controller is not natively supported then you'll want
to boot the Windows 2000 install CD-Rom. Then *F6* very early and very
important (at setup is inspecting your system) in the setup to prevent drive
controller detection, and select S to specify additional drivers. Then later
you'll be prompted to insert the manufacturer supplied Windows 2000 driver
for your drive controller in drive "A")
Setup inspects your computer's hardware configuration and then begins to
install the Setup and driver files. When the Windows 2000 Professional
screen appears, press ENTER to set up Windows 2000 Professional.
Read the license agreement, and then press the F8 key to accept the terms of
the license agreement and continue the installation.
When the Windows 2000 Professional Setup screen appears, all the existing
partitions and the unpartitioned spaces are listed for each physical hard
disk. Use the ARROW keys to select the partitions Press D to delete an
existing partition, If you press D to delete an existing partition, you must
then press L (or press ENTER, and then press L if it is the System
partition) to confirm that you want to delete the partition. Repeat this
step for each of the existing partitions When all the partitions are deleted
press F3 to exit setup, (to avoid unexpected drive letter assignments with
your new install) then restart the pc then when you get to this point in
setup again select the unpartitioned space, and then press C to create a new
partition and specify the size (if required). Windows will by default use
all available space.
Be sure to apply SP4 and these two below to your new install before
connecting to any network. Internet included. (sasser, msblast)
http://download.microsoft.com/download/E/6/A/E6A04295-D2A8-40D0-A0C5-241BFECD095E/W2KSP4_EN.EXE
http://www.microsoft.com/technet/security/bulletin/MS03-043.mspx
http://www.microsoft.com/technet/security/bulletin/MS03-049.mspx
Then
Rollup 1 for Microsoft Windows 2000 Service Pack 4
http://www.microsoft.com/downloads/details.aspx?amp;displaylang=en&familyid=B54730CF-8850-4531-B52B-BF28B324C662&displaylang=en
--
Regards,
Dave Patrick ....Please no email replies - reply in newsgroup.
Microsoft Certified Professional
Microsoft MVP [Windows]
http://www.microsoft.com/protect
"Lee MacMillan" wrote:
> Recently had to replace a failed mobo and do a repair install. All went
> well and I've got all the service packs updated. The system runs fine if
> it
> starts but about every 3rd start up attempt (I only use this machine 2 or
> 3
> times a week), as soon as Windows starts to load (after the main screen),
> I'll get a blue screen with the message "system halted, contact your
> hardware vendor."
>
> I haven't changed any components other than the mobo (an Epox 8KHA+ that
> was
> in my WinXP machine for several years). As noted, if Windows loads, the
> sytem runs fine with no indication of a problem. At first I thought my
> network card wasn't fully seated but I pulled it out and got the same
> error.
> I have 3 SDRAM sticks (2x256 and 1x512), a Radeon 9250 video card, 1
> Seagate 80gig drive, 1 floppy and an HP CDRW.
>
> From my research I assume this is some kind of hardware problem but since
> it's intermittant, I don't where to start. All suggestions are welcome.
>
>