Microsoft LifeCam VX-3000 does not work after hibernation state

Hello!

I have got an Microsoft LifeCam VX-3000. the LifeCam dies not work after the computer was
sent to hibernation and came back from it.

I have got other devices sticking in other usb hubs that function with no problems (usb flash
drive, a keyboard, external hard drive ).

When the cam was up and running prior to hibernation or while hibernation :-), everything will
be fine. Also, what I can do was to un-plug and to re-plug the cam to the same hub. That's but
no clue since I had to un-plug and to re-plug the cam each time. When I run the program after
hibernation with no prior preparation the cams image(s ) will not show up, but a black square
only and the green light on top of the cam does not flash

Was any one used to the problem and can help?

Thank you,
Steve

Bob
Tue Apr 08 05:44:33 PDT 2008

Go into Device Manager and in the Universal Serial Serial Bus section,
go through the hubs,r-click on them, open "Properties", then on the
Power Management tab, UNcheck "Allow the computer to turn off this
device........"

Steve Miller wrote:

> Hello!
>
> I have got an Microsoft LifeCam VX-3000. the LifeCam dies not work after the computer was
> sent to hibernation and came back from it.
>
> I have got other devices sticking in other usb hubs that function with no problems (usb flash
> drive, a keyboard, external hard drive ).
>
> When the cam was up and running prior to hibernation or while hibernation :-), everything will
> be fine. Also, what I can do was to un-plug and to re-plug the cam to the same hub. That's but
> no clue since I had to un-plug and to re-plug the cam each time. When I run the program after
> hibernation with no prior preparation the cams image(s ) will not show up, but a black square
> only and the green light on top of the cam does not flash
>
> Was any one used to the problem and can help?
>
> Thank you,
> Steve
>
>

Steve
Tue Apr 08 05:57:48 PDT 2008

Hi Bob I!

Thank you for your reply. I did, but didn't help at all. Sorry I forgot to mention.

Steve

"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OHi7LZXmIHA.3780@TK2MSFTNGP06.phx.gbl...
> Go into Device Manager and in the Universal Serial Serial Bus section, go through the hubs,r-click on them, open "Properties",
> then on the Power Management tab, UNcheck "Allow the computer to turn off this device........"
>
> Steve Miller wrote:
>
>> Hello!
>>
>> I have got an Microsoft LifeCam VX-3000. the LifeCam dies not work after the computer was
>> sent to hibernation and came back from it.
>>
>> I have got other devices sticking in other usb hubs that function with no problems (usb flash
>> drive, a keyboard, external hard drive ).
>>
>> When the cam was up and running prior to hibernation or while hibernation :-), everything will
>> be fine. Also, what I can do was to un-plug and to re-plug the cam to the same hub. That's but
>> no clue since I had to un-plug and to re-plug the cam each time. When I run the program after
>> hibernation with no prior preparation the cams image(s ) will not show up, but a black square
>> only and the green light on top of the cam does not flash
>>
>> Was any one used to the problem and can help?
>>
>> Thank you,
>> Steve
>

Bob
Tue Apr 08 07:39:14 PDT 2008

Perhaps plug it into a powered hub?

Steve Miller wrote:

> Hi Bob I!
>
> Thank you for your reply. I did, but didn't help at all. Sorry I forgot to mention.
>
> Steve
>
> "Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OHi7LZXmIHA.3780@TK2MSFTNGP06.phx.gbl...
>
>>Go into Device Manager and in the Universal Serial Serial Bus section, go through the hubs,r-click on them, open "Properties",
>>then on the Power Management tab, UNcheck "Allow the computer to turn off this device........"
>>
>>Steve Miller wrote:
>>
>>
>>>Hello!
>>>
>>>I have got an Microsoft LifeCam VX-3000. the LifeCam dies not work after the computer was
>>>sent to hibernation and came back from it.
>>>
>>>I have got other devices sticking in other usb hubs that function with no problems (usb flash
>>>drive, a keyboard, external hard drive ).
>>>
>>>When the cam was up and running prior to hibernation or while hibernation :-), everything will
>>>be fine. Also, what I can do was to un-plug and to re-plug the cam to the same hub. That's but
>>>no clue since I had to un-plug and to re-plug the cam each time. When I run the program after
>>>hibernation with no prior preparation the cams image(s ) will not show up, but a black square
>>>only and the green light on top of the cam does not flash
>>>
>>>Was any one used to the problem and can help?
>>>
>>>Thank you,
>>>Steve
>>
>
>

Steve
Tue Apr 08 07:59:27 PDT 2008

Bob I, I think the hub was powered. I could plug the usb drive in the cams hub, it will work.

I even could unplug the cam prior to starting the LifeCam program and plug it back into the
same hub the program still off, the cam will work.

It also works fine with a freshly booted up computer and after standby also. Only after
hibernation it does not.

Steve

"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:eeugSZYmIHA.1912@TK2MSFTNGP04.phx.gbl...
> Perhaps plug it into a powered hub?
>
> Steve Miller wrote:
>
>> Hi Bob I!
>>
>> Thank you for your reply. I did, but didn't help at all. Sorry I forgot to mention.
>>
>> Steve
>>
>> "Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OHi7LZXmIHA.3780@TK2MSFTNGP06.phx.gbl...
>>
>>>Go into Device Manager and in the Universal Serial Serial Bus section, go through the hubs,r-click on them, open "Properties",
>>>then on the Power Management tab, UNcheck "Allow the computer to turn off this device........"
>>>
>>>Steve Miller wrote:
>>>
>>>
>>>>Hello!
>>>>
>>>>I have got an Microsoft LifeCam VX-3000. the LifeCam dies not work after the computer was
>>>>sent to hibernation and came back from it.
>>>>
>>>>I have got other devices sticking in other usb hubs that function with no problems (usb flash
>>>>drive, a keyboard, external hard drive ).
>>>>
>>>>When the cam was up and running prior to hibernation or while hibernation :-), everything will
>>>>be fine. Also, what I can do was to un-plug and to re-plug the cam to the same hub. That's but
>>>>no clue since I had to un-plug and to re-plug the cam each time. When I run the program after
>>>>hibernation with no prior preparation the cams image(s ) will not show up, but a black square
>>>>only and the green light on top of the cam does not flash
>>>>
>>>>Was any one used to the problem and can help?
>>>>
>>>>Thank you,
>>>>Steve
>>>
>>
>>
>

Bob
Tue Apr 08 08:26:55 PDT 2008

In hibernation the PC shuts off, and does not look for "new" things when
powered back on. Perhaps "find new hardware" will restore the cam
after hibernation.

Steve Miller wrote:
> Bob I, I think the hub was powered. I could plug the usb drive in the cams hub, it will work.
>
> I even could unplug the cam prior to starting the LifeCam program and plug it back into the
> same hub the program still off, the cam will work.
>
> It also works fine with a freshly booted up computer and after standby also. Only after
> hibernation it does not.
>
> Steve
>
> "Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:eeugSZYmIHA.1912@TK2MSFTNGP04.phx.gbl...
>
>>Perhaps plug it into a powered hub?
>>
>>Steve Miller wrote:
>>
>>
>>>Hi Bob I!
>>>
>>>Thank you for your reply. I did, but didn't help at all. Sorry I forgot to mention.
>>>
>>>Steve
>>>
>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OHi7LZXmIHA.3780@TK2MSFTNGP06.phx.gbl...
>>>
>>>
>>>>Go into Device Manager and in the Universal Serial Serial Bus section, go through the hubs,r-click on them, open "Properties",
>>>>then on the Power Management tab, UNcheck "Allow the computer to turn off this device........"
>>>>
>>>>Steve Miller wrote:
>>>>
>>>>
>>>>
>>>>>Hello!
>>>>>
>>>>>I have got an Microsoft LifeCam VX-3000. the LifeCam dies not work after the computer was
>>>>>sent to hibernation and came back from it.
>>>>>
>>>>>I have got other devices sticking in other usb hubs that function with no problems (usb flash
>>>>>drive, a keyboard, external hard drive ).
>>>>>
>>>>>When the cam was up and running prior to hibernation or while hibernation :-), everything will
>>>>>be fine. Also, what I can do was to un-plug and to re-plug the cam to the same hub. That's but
>>>>>no clue since I had to un-plug and to re-plug the cam each time. When I run the program after
>>>>>hibernation with no prior preparation the cams image(s ) will not show up, but a black square
>>>>>only and the green light on top of the cam does not flash
>>>>>
>>>>>Was any one used to the problem and can help?
>>>>>
>>>>>Thank you,
>>>>>Steve
>>>>
>>>
>
>

Steve
Tue Apr 08 08:50:39 PDT 2008

The cam was not actually new hardware after hibernation. All the other usb devices are
ok after hibernation and to function correct with no failure. Only the cam does not.

The motherboard was from around '04, and I did install all the latest drivers but now do
have the one installed Windows XP picked. All the same.

Steve

"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:%23mka7zYmIHA.6032@TK2MSFTNGP03.phx.gbl...
> In hibernation the PC shuts off, and does not look for "new" things when powered back on. Perhaps "find new hardware" will restore
> the cam after hibernation.
>
> Steve Miller wrote:
>> Bob I, I think the hub was powered. I could plug the usb drive in the cams hub, it will work.
>>
>> I even could unplug the cam prior to starting the LifeCam program and plug it back into the
>> same hub the program still off, the cam will work.
>>
>> It also works fine with a freshly booted up computer and after standby also. Only after
>> hibernation it does not.
>>
>> Steve
>>
>> "Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:eeugSZYmIHA.1912@TK2MSFTNGP04.phx.gbl...
>>
>>>Perhaps plug it into a powered hub?
>>>
>>>Steve Miller wrote:
>>>
>>>
>>>>Hi Bob I!
>>>>
>>>>Thank you for your reply. I did, but didn't help at all. Sorry I forgot to mention.
>>>>
>>>>Steve
>>>>
>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OHi7LZXmIHA.3780@TK2MSFTNGP06.phx.gbl...
>>>>
>>>>
>>>>>Go into Device Manager and in the Universal Serial Serial Bus section, go through the hubs,r-click on them, open "Properties",
>>>>>then on the Power Management tab, UNcheck "Allow the computer to turn off this device........"
>>>>>
>>>>>Steve Miller wrote:
>>>>>
>>>>>
>>>>>
>>>>>>Hello!
>>>>>>
>>>>>>I have got an Microsoft LifeCam VX-3000. the LifeCam dies not work after the computer was
>>>>>>sent to hibernation and came back from it.
>>>>>>
>>>>>>I have got other devices sticking in other usb hubs that function with no problems (usb flash
>>>>>>drive, a keyboard, external hard drive ).
>>>>>>
>>>>>>When the cam was up and running prior to hibernation or while hibernation :-), everything will
>>>>>>be fine. Also, what I can do was to un-plug and to re-plug the cam to the same hub. That's but
>>>>>>no clue since I had to un-plug and to re-plug the cam each time. When I run the program after
>>>>>>hibernation with no prior preparation the cams image(s ) will not show up, but a black square
>>>>>>only and the green light on top of the cam does not flash
>>>>>>
>>>>>>Was any one used to the problem and can help?
>>>>>>
>>>>>>Thank you,
>>>>>>Steve
>>>>>
>>>>
>>
>>
>

Bob
Tue Apr 08 09:00:23 PDT 2008

Does the cam remain "on" though the hibernation period?

Steve Miller wrote:

> The cam was not actually new hardware after hibernation. All the other usb devices are
> ok after hibernation and to function correct with no failure. Only the cam does not.
>
> The motherboard was from around '04, and I did install all the latest drivers but now do
> have the one installed Windows XP picked. All the same.
>
> Steve
>
> "Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:%23mka7zYmIHA.6032@TK2MSFTNGP03.phx.gbl...
>
>>In hibernation the PC shuts off, and does not look for "new" things when powered back on. Perhaps "find new hardware" will restore
>>the cam after hibernation.
>>
>>Steve Miller wrote:
>>
>>>Bob I, I think the hub was powered. I could plug the usb drive in the cams hub, it will work.
>>>
>>>I even could unplug the cam prior to starting the LifeCam program and plug it back into the
>>>same hub the program still off, the cam will work.
>>>
>>>It also works fine with a freshly booted up computer and after standby also. Only after
>>>hibernation it does not.
>>>
>>>Steve
>>>
>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:eeugSZYmIHA.1912@TK2MSFTNGP04.phx.gbl...
>>>
>>>
>>>>Perhaps plug it into a powered hub?
>>>>
>>>>Steve Miller wrote:
>>>>
>>>>
>>>>
>>>>>Hi Bob I!
>>>>>
>>>>>Thank you for your reply. I did, but didn't help at all. Sorry I forgot to mention.
>>>>>
>>>>>Steve
>>>>>
>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OHi7LZXmIHA.3780@TK2MSFTNGP06.phx.gbl...
>>>>>
>>>>>
>>>>>
>>>>>>Go into Device Manager and in the Universal Serial Serial Bus section, go through the hubs,r-click on them, open "Properties",
>>>>>>then on the Power Management tab, UNcheck "Allow the computer to turn off this device........"
>>>>>>
>>>>>>Steve Miller wrote:
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>>Hello!
>>>>>>>
>>>>>>>I have got an Microsoft LifeCam VX-3000. the LifeCam dies not work after the computer was
>>>>>>>sent to hibernation and came back from it.
>>>>>>>
>>>>>>>I have got other devices sticking in other usb hubs that function with no problems (usb flash
>>>>>>>drive, a keyboard, external hard drive ).
>>>>>>>
>>>>>>>When the cam was up and running prior to hibernation or while hibernation :-), everything will
>>>>>>>be fine. Also, what I can do was to un-plug and to re-plug the cam to the same hub. That's but
>>>>>>>no clue since I had to un-plug and to re-plug the cam each time. When I run the program after
>>>>>>>hibernation with no prior preparation the cams image(s ) will not show up, but a black square
>>>>>>>only and the green light on top of the cam does not flash
>>>>>>>
>>>>>>>Was any one used to the problem and can help?
>>>>>>>
>>>>>>>Thank you,
>>>>>>>Steve
>>>>>>
>>>
>
>

Steve
Tue Apr 08 09:37:12 PDT 2008

When the program was running before hibernation the green light goes off while the computer
goes to sleep ánd is back up when the computer was wake. The cam was 'off' while the computer
was in hibernation mode.

"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:ezQXoGZmIHA.4196@TK2MSFTNGP04.phx.gbl...
> Does the cam remain "on" though the hibernation period?
>
> Steve Miller wrote:
>
>> The cam was not actually new hardware after hibernation. All the other usb devices are
>> ok after hibernation and to function correct with no failure. Only the cam does not.
>>
>> The motherboard was from around '04, and I did install all the latest drivers but now do
>> have the one installed Windows XP picked. All the same.
>>
>> Steve
>>
>> "Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:%23mka7zYmIHA.6032@TK2MSFTNGP03.phx.gbl...
>>
>>>In hibernation the PC shuts off, and does not look for "new" things when powered back on. Perhaps "find new hardware" will
>>>restore the cam after hibernation.
>>>
>>>Steve Miller wrote:
>>>
>>>>Bob I, I think the hub was powered. I could plug the usb drive in the cams hub, it will work.
>>>>
>>>>I even could unplug the cam prior to starting the LifeCam program and plug it back into the
>>>>same hub the program still off, the cam will work.
>>>>
>>>>It also works fine with a freshly booted up computer and after standby also. Only after
>>>>hibernation it does not.
>>>>
>>>>Steve
>>>>
>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:eeugSZYmIHA.1912@TK2MSFTNGP04.phx.gbl...
>>>>
>>>>
>>>>>Perhaps plug it into a powered hub?
>>>>>
>>>>>Steve Miller wrote:
>>>>>
>>>>>
>>>>>
>>>>>>Hi Bob I!
>>>>>>
>>>>>>Thank you for your reply. I did, but didn't help at all. Sorry I forgot to mention.
>>>>>>
>>>>>>Steve
>>>>>>
>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OHi7LZXmIHA.3780@TK2MSFTNGP06.phx.gbl...
>>>>>>
>>>>>>
>>>>>>
>>>>>>>Go into Device Manager and in the Universal Serial Serial Bus section, go through the hubs,r-click on them, open
>>>>>>>"Properties", then on the Power Management tab, UNcheck "Allow the computer to turn off this device........"
>>>>>>>
>>>>>>>Steve Miller wrote:
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>>Hello!
>>>>>>>>
>>>>>>>>I have got an Microsoft LifeCam VX-3000. the LifeCam dies not work after the computer was
>>>>>>>>sent to hibernation and came back from it.
>>>>>>>>
>>>>>>>>I have got other devices sticking in other usb hubs that function with no problems (usb flash
>>>>>>>>drive, a keyboard, external hard drive ).
>>>>>>>>
>>>>>>>>When the cam was up and running prior to hibernation or while hibernation :-), everything will
>>>>>>>>be fine. Also, what I can do was to un-plug and to re-plug the cam to the same hub. That's but
>>>>>>>>no clue since I had to un-plug and to re-plug the cam each time. When I run the program after
>>>>>>>>hibernation with no prior preparation the cams image(s ) will not show up, but a black square
>>>>>>>>only and the green light on top of the cam does not flash
>>>>>>>>
>>>>>>>>Was any one used to the problem and can help?
>>>>>>>>
>>>>>>>>Thank you,
>>>>>>>>Steve
>>>>>>>
>>>>
>>
>>
>

Bob
Tue Apr 08 10:07:31 PDT 2008

If the green light is on after the PC is back up, try "find new hardware"=
=2E

Steve Miller wrote:
> When the program was running before hibernation the green light goes of=
f while the computer
> goes to sleep =E1nd is back up when the computer was wake. The cam was =
'off' while the computer
> was in hibernation mode.
>=20
> "Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:ezQXoGZmIHA.419=
6@TK2MSFTNGP04.phx.gbl...
>=20
>>Does the cam remain "on" though the hibernation period?
>>
>>Steve Miller wrote:
>>
>>
>>>The cam was not actually new hardware after hibernation. All the other=
usb devices are
>>>ok after hibernation and to function correct with no failure. Only the=
cam does not.
>>>
>>>The motherboard was from around '04, and I did install all the latest =
drivers but now do
>>>have the one installed Windows XP picked. All the same.
>>>
>>>Steve
>>>
>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:%23mka7zYmIHA.=
6032@TK2MSFTNGP03.phx.gbl...
>>>
>>>
>>>>In hibernation the PC shuts off, and does not look for "new" things w=
hen powered back on. Perhaps "find new hardware" will=20
>>>>restore the cam after hibernation.
>>>>
>>>>Steve Miller wrote:
>>>>
>>>>
>>>>>Bob I, I think the hub was powered. I could plug the usb drive in th=
e cams hub, it will work.
>>>>>
>>>>>I even could unplug the cam prior to starting the LifeCam program an=
d plug it back into the
>>>>>same hub the program still off, the cam will work.
>>>>>
>>>>>It also works fine with a freshly booted up computer and after stand=
by also. Only after
>>>>>hibernation it does not.
>>>>>
>>>>>Steve
>>>>>
>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:eeugSZYmIHA.=
1912@TK2MSFTNGP04.phx.gbl...
>>>>>
>>>>>
>>>>>
>>>>>>Perhaps plug it into a powered hub?
>>>>>>
>>>>>>Steve Miller wrote:
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>>Hi Bob I!
>>>>>>>
>>>>>>>Thank you for your reply. I did, but didn't help at all. Sorry I f=
orgot to mention.
>>>>>>>
>>>>>>>Steve
>>>>>>>
>>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OHi7LZXmIH=
A.3780@TK2MSFTNGP06.phx.gbl...
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>>Go into Device Manager and in the Universal Serial Serial Bus sec=
tion, go through the hubs,r-click on them, open=20
>>>>>>>>"Properties", then on the Power Management tab, UNcheck "Allow th=
e computer to turn off this device........"
>>>>>>>>
>>>>>>>>Steve Miller wrote:
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>>Hello!
>>>>>>>>>
>>>>>>>>>I have got an Microsoft LifeCam VX-3000. the LifeCam dies not wo=
rk after the computer was
>>>>>>>>>sent to hibernation and came back from it.
>>>>>>>>>
>>>>>>>>>I have got other devices sticking in other usb hubs that functio=
n with no problems (usb flash
>>>>>>>>>drive, a keyboard, external hard drive ).
>>>>>>>>>
>>>>>>>>>When the cam was up and running prior to hibernation or while hi=
bernation :-), everything will
>>>>>>>>>be fine. Also, what I can do was to un-plug and to re-plug the c=
am to the same hub. That's but
>>>>>>>>>no clue since I had to un-plug and to re-plug the cam each time.=
When I run the program after
>>>>>>>>>hibernation with no prior preparation the cams image(s ) will no=
t show up, but a black square
>>>>>>>>>only and the green light on top of the cam does not flash
>>>>>>>>>
>>>>>>>>>Was any one used to the problem and can help?
>>>>>>>>>
>>>>>>>>>Thank you,
>>>>>>>>>Steve
>>>>>>>>
>>>
>=20
>=20

Steve
Tue Apr 08 10:31:50 PDT 2008

That's a good idea since the cam was working already. :-) What else could I try out?

I still hope that there was some setting I'm not used to now that would fix the issue.

Steve

"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:u6$FJsZmIHA.1280@TK2MSFTNGP05.phx.gbl...
If the green light is on after the PC is back up, try "find new hardware".

Steve Miller wrote:
> When the program was running before hibernation the green light goes off while the computer
> goes to sleep ánd is back up when the computer was wake. The cam was 'off' while the computer
> was in hibernation mode.
>
> "Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:ezQXoGZmIHA.4196@TK2MSFTNGP04.phx.gbl...
>
>>Does the cam remain "on" though the hibernation period?
>>
>>Steve Miller wrote:
>>
>>
>>>The cam was not actually new hardware after hibernation. All the other usb devices are
>>>ok after hibernation and to function correct with no failure. Only the cam does not.
>>>
>>>The motherboard was from around '04, and I did install all the latest drivers but now do
>>>have the one installed Windows XP picked. All the same.
>>>
>>>Steve
>>>
>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:%23mka7zYmIHA.6032@TK2MSFTNGP03.phx.gbl...
>>>
>>>
>>>>In hibernation the PC shuts off, and does not look for "new" things when powered back on. Perhaps "find new hardware" will
>>>>restore the cam after hibernation.
>>>>
>>>>Steve Miller wrote:
>>>>
>>>>
>>>>>Bob I, I think the hub was powered. I could plug the usb drive in the cams hub, it will work.
>>>>>
>>>>>I even could unplug the cam prior to starting the LifeCam program and plug it back into the
>>>>>same hub the program still off, the cam will work.
>>>>>
>>>>>It also works fine with a freshly booted up computer and after standby also. Only after
>>>>>hibernation it does not.
>>>>>
>>>>>Steve
>>>>>
>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:eeugSZYmIHA.1912@TK2MSFTNGP04.phx.gbl...
>>>>>
>>>>>
>>>>>
>>>>>>Perhaps plug it into a powered hub?
>>>>>>
>>>>>>Steve Miller wrote:
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>>Hi Bob I!
>>>>>>>
>>>>>>>Thank you for your reply. I did, but didn't help at all. Sorry I forgot to mention.
>>>>>>>
>>>>>>>Steve
>>>>>>>
>>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OHi7LZXmIHA.3780@TK2MSFTNGP06.phx.gbl...
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>>Go into Device Manager and in the Universal Serial Serial Bus section, go through the hubs,r-click on them, open
>>>>>>>>"Properties", then on the Power Management tab, UNcheck "Allow the computer to turn off this device........"
>>>>>>>>
>>>>>>>>Steve Miller wrote:
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>>Hello!
>>>>>>>>>
>>>>>>>>>I have got an Microsoft LifeCam VX-3000. the LifeCam dies not work after the computer was
>>>>>>>>>sent to hibernation and came back from it.
>>>>>>>>>
>>>>>>>>>I have got other devices sticking in other usb hubs that function with no problems (usb flash
>>>>>>>>>drive, a keyboard, external hard drive ).
>>>>>>>>>
>>>>>>>>>When the cam was up and running prior to hibernation or while hibernation :-), everything will
>>>>>>>>>be fine. Also, what I can do was to un-plug and to re-plug the cam to the same hub. That's but
>>>>>>>>>no clue since I had to un-plug and to re-plug the cam each time. When I run the program after
>>>>>>>>>hibernation with no prior preparation the cams image(s ) will not show up, but a black square
>>>>>>>>>only and the green light on top of the cam does not flash
>>>>>>>>>
>>>>>>>>>Was any one used to the problem and can help?
>>>>>>>>>
>>>>>>>>>Thank you,
>>>>>>>>>Steve
>>>>>>>>
>>>
>
>

Bob
Tue Apr 08 10:38:39 PDT 2008

Try plugging directly into the PC, or contact MS tech support, or=20
replace the camera.

Steve Miller wrote:

> That's a good idea since the cam was working already. :-) What else cou=
ld I try out?
>=20
> I still hope that there was some setting I'm not used to now that would=
fix the issue.
>=20
> Steve
>=20
> "Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:u6$FJsZmIHA.128=
0@TK2MSFTNGP05.phx.gbl...
> If the green light is on after the PC is back up, try "find new hardwar=
e".
>=20
> Steve Miller wrote:
>=20
>>When the program was running before hibernation the green light goes of=
f while the computer
>>goes to sleep =E1nd is back up when the computer was wake. The cam was =
'off' while the computer
>>was in hibernation mode.
>>
>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:ezQXoGZmIHA.419=
6@TK2MSFTNGP04.phx.gbl...
>>
>>
>>>Does the cam remain "on" though the hibernation period?
>>>
>>>Steve Miller wrote:
>>>
>>>
>>>
>>>>The cam was not actually new hardware after hibernation. All the othe=
r usb devices are
>>>>ok after hibernation and to function correct with no failure. Only th=
e cam does not.
>>>>
>>>>The motherboard was from around '04, and I did install all the latest=
drivers but now do
>>>>have the one installed Windows XP picked. All the same.
>>>>
>>>>Steve
>>>>
>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:%23mka7zYmIHA=
=2E6032@TK2MSFTNGP03.phx.gbl...
>>>>
>>>>
>>>>
>>>>>In hibernation the PC shuts off, and does not look for "new" things =
when powered back on. Perhaps "find new hardware" will=20
>>>>>restore the cam after hibernation.
>>>>>
>>>>>Steve Miller wrote:
>>>>>
>>>>>
>>>>>
>>>>>>Bob I, I think the hub was powered. I could plug the usb drive in t=
he cams hub, it will work.
>>>>>>
>>>>>>I even could unplug the cam prior to starting the LifeCam program a=
nd plug it back into the
>>>>>>same hub the program still off, the cam will work.
>>>>>>
>>>>>>It also works fine with a freshly booted up computer and after stan=
dby also. Only after
>>>>>>hibernation it does not.
>>>>>>
>>>>>>Steve
>>>>>>
>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:eeugSZYmIHA=
=2E1912@TK2MSFTNGP04.phx.gbl...
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>>Perhaps plug it into a powered hub?
>>>>>>>
>>>>>>>Steve Miller wrote:
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>>Hi Bob I!
>>>>>>>>
>>>>>>>>Thank you for your reply. I did, but didn't help at all. Sorry I =
forgot to mention.
>>>>>>>>
>>>>>>>>Steve
>>>>>>>>
>>>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OHi7LZXmI=
HA.3780@TK2MSFTNGP06.phx.gbl...
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>>Go into Device Manager and in the Universal Serial Serial Bus se=
ction, go through the hubs,r-click on them, open=20
>>>>>>>>>"Properties", then on the Power Management tab, UNcheck "Allow t=
he computer to turn off this device........"
>>>>>>>>>
>>>>>>>>>Steve Miller wrote:
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>>Hello!
>>>>>>>>>>
>>>>>>>>>>I have got an Microsoft LifeCam VX-3000. the LifeCam dies not w=
ork after the computer was
>>>>>>>>>>sent to hibernation and came back from it.
>>>>>>>>>>
>>>>>>>>>>I have got other devices sticking in other usb hubs that functi=
on with no problems (usb flash
>>>>>>>>>>drive, a keyboard, external hard drive ).
>>>>>>>>>>
>>>>>>>>>>When the cam was up and running prior to hibernation or while h=
ibernation :-), everything will
>>>>>>>>>>be fine. Also, what I can do was to un-plug and to re-plug the =
cam to the same hub. That's but
>>>>>>>>>>no clue since I had to un-plug and to re-plug the cam each time=
=2E When I run the program after
>>>>>>>>>>hibernation with no prior preparation the cams image(s ) will n=
ot show up, but a black square
>>>>>>>>>>only and the green light on top of the cam does not flash
>>>>>>>>>>
>>>>>>>>>>Was any one used to the problem and can help?
>>>>>>>>>>
>>>>>>>>>>Thank you,
>>>>>>>>>>Steve
>>>>>>>>>
>>
>=20
>=20

Steve
Tue Apr 08 10:50:31 PDT 2008

Do you think it could be something with the chip set or there like?

"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:uudzi9ZmIHA.5368@TK2MSFTNGP04.phx.gbl...
Try plugging directly into the PC, or contact MS tech support, or
replace the camera.

Steve Miller wrote:

> That's a good idea since the cam was working already. :-) What else could I try out?
>
> I still hope that there was some setting I'm not used to now that would fix the issue.
>
> Steve
>
> "Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:u6$FJsZmIHA.1280@TK2MSFTNGP05.phx.gbl...
> If the green light is on after the PC is back up, try "find new hardware".
>
> Steve Miller wrote:
>
>>When the program was running before hibernation the green light goes off while the computer
>>goes to sleep ánd is back up when the computer was wake. The cam was 'off' while the computer
>>was in hibernation mode.
>>
>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:ezQXoGZmIHA.4196@TK2MSFTNGP04.phx.gbl...
>>
>>
>>>Does the cam remain "on" though the hibernation period?
>>>
>>>Steve Miller wrote:
>>>
>>>
>>>
>>>>The cam was not actually new hardware after hibernation. All the other usb devices are
>>>>ok after hibernation and to function correct with no failure. Only the cam does not.
>>>>
>>>>The motherboard was from around '04, and I did install all the latest drivers but now do
>>>>have the one installed Windows XP picked. All the same.
>>>>
>>>>Steve
>>>>
>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:%23mka7zYmIHA.6032@TK2MSFTNGP03.phx.gbl...
>>>>
>>>>
>>>>
>>>>>In hibernation the PC shuts off, and does not look for "new" things when powered back on. Perhaps "find new hardware" will
>>>>>restore the cam after hibernation.
>>>>>
>>>>>Steve Miller wrote:
>>>>>
>>>>>
>>>>>
>>>>>>Bob I, I think the hub was powered. I could plug the usb drive in the cams hub, it will work.
>>>>>>
>>>>>>I even could unplug the cam prior to starting the LifeCam program and plug it back into the
>>>>>>same hub the program still off, the cam will work.
>>>>>>
>>>>>>It also works fine with a freshly booted up computer and after standby also. Only after
>>>>>>hibernation it does not.
>>>>>>
>>>>>>Steve
>>>>>>
>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:eeugSZYmIHA.1912@TK2MSFTNGP04.phx.gbl...
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>>Perhaps plug it into a powered hub?
>>>>>>>
>>>>>>>Steve Miller wrote:
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>>Hi Bob I!
>>>>>>>>
>>>>>>>>Thank you for your reply. I did, but didn't help at all. Sorry I forgot to mention.
>>>>>>>>
>>>>>>>>Steve
>>>>>>>>
>>>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OHi7LZXmIHA.3780@TK2MSFTNGP06.phx.gbl...
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>>Go into Device Manager and in the Universal Serial Serial Bus section, go through the hubs,r-click on them, open
>>>>>>>>>"Properties", then on the Power Management tab, UNcheck "Allow the computer to turn off this device........"
>>>>>>>>>
>>>>>>>>>Steve Miller wrote:
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>>Hello!
>>>>>>>>>>
>>>>>>>>>>I have got an Microsoft LifeCam VX-3000. the LifeCam dies not work after the computer was
>>>>>>>>>>sent to hibernation and came back from it.
>>>>>>>>>>
>>>>>>>>>>I have got other devices sticking in other usb hubs that function with no problems (usb flash
>>>>>>>>>>drive, a keyboard, external hard drive ).
>>>>>>>>>>
>>>>>>>>>>When the cam was up and running prior to hibernation or while hibernation :-), everything will
>>>>>>>>>>be fine. Also, what I can do was to un-plug and to re-plug the cam to the same hub. That's but
>>>>>>>>>>no clue since I had to un-plug and to re-plug the cam each time. When I run the program after
>>>>>>>>>>hibernation with no prior preparation the cams image(s ) will not show up, but a black square
>>>>>>>>>>only and the green light on top of the cam does not flash
>>>>>>>>>>
>>>>>>>>>>Was any one used to the problem and can help?
>>>>>>>>>>
>>>>>>>>>>Thank you,
>>>>>>>>>>Steve
>>>>>>>>>
>>
>
>

Bob
Tue Apr 08 11:32:48 PDT 2008

Given that everything else comes back ok, I would hesitate to condemn=20
the chipset/motherboard.

Steve Miller wrote:
> Do you think it could be something with the chip set or there like?
>=20
> "Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:uudzi9ZmIHA.536=
8@TK2MSFTNGP04.phx.gbl...
> Try plugging directly into the PC, or contact MS tech support, or
> replace the camera.
>=20
> Steve Miller wrote:
>=20
>=20
>>That's a good idea since the cam was working already. :-) What else cou=
ld I try out?
>>
>>I still hope that there was some setting I'm not used to now that would=
fix the issue.
>>
>>Steve
>>
>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:u6$FJsZmIHA.128=
0@TK2MSFTNGP05.phx.gbl...
>>If the green light is on after the PC is back up, try "find new hardwar=
e".
>>
>>Steve Miller wrote:
>>
>>
>>>When the program was running before hibernation the green light goes o=
ff while the computer
>>>goes to sleep =E1nd is back up when the computer was wake. The cam was=
'off' while the computer
>>>was in hibernation mode.
>>>
>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:ezQXoGZmIHA.41=
96@TK2MSFTNGP04.phx.gbl...
>>>
>>>
>>>
>>>>Does the cam remain "on" though the hibernation period?
>>>>
>>>>Steve Miller wrote:
>>>>
>>>>
>>>>
>>>>
>>>>>The cam was not actually new hardware after hibernation. All the oth=
er usb devices are
>>>>>ok after hibernation and to function correct with no failure. Only t=
he cam does not.
>>>>>
>>>>>The motherboard was from around '04, and I did install all the lates=
t drivers but now do
>>>>>have the one installed Windows XP picked. All the same.
>>>>>
>>>>>Steve
>>>>>
>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:%23mka7zYmIH=
A.6032@TK2MSFTNGP03.phx.gbl...
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>>In hibernation the PC shuts off, and does not look for "new" things=
when powered back on. Perhaps "find new hardware" will=20
>>>>>>restore the cam after hibernation.
>>>>>>
>>>>>>Steve Miller wrote:
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>>Bob I, I think the hub was powered. I could plug the usb drive in =
the cams hub, it will work.
>>>>>>>
>>>>>>>I even could unplug the cam prior to starting the LifeCam program =
and plug it back into the
>>>>>>>same hub the program still off, the cam will work.
>>>>>>>
>>>>>>>It also works fine with a freshly booted up computer and after sta=
ndby also. Only after
>>>>>>>hibernation it does not.
>>>>>>>
>>>>>>>Steve
>>>>>>>
>>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:eeugSZYmIH=
A.1912@TK2MSFTNGP04.phx.gbl...
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>>Perhaps plug it into a powered hub?
>>>>>>>>
>>>>>>>>Steve Miller wrote:
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>>Hi Bob I!
>>>>>>>>>
>>>>>>>>>Thank you for your reply. I did, but didn't help at all. Sorry I=
forgot to mention.
>>>>>>>>>
>>>>>>>>>Steve
>>>>>>>>>
>>>>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OHi7LZXm=
IHA.3780@TK2MSFTNGP06.phx.gbl...
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>>Go into Device Manager and in the Universal Serial Serial Bus s=
ection, go through the hubs,r-click on them, open=20
>>>>>>>>>>"Properties", then on the Power Management tab, UNcheck "Allow =
the computer to turn off this device........"
>>>>>>>>>>
>>>>>>>>>>Steve Miller wrote:
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>>Hello!
>>>>>>>>>>>
>>>>>>>>>>>I have got an Microsoft LifeCam VX-3000. the LifeCam dies not =
work after the computer was
>>>>>>>>>>>sent to hibernation and came back from it.
>>>>>>>>>>>
>>>>>>>>>>>I have got other devices sticking in other usb hubs that funct=
ion with no problems (usb flash
>>>>>>>>>>>drive, a keyboard, external hard drive ).
>>>>>>>>>>>
>>>>>>>>>>>When the cam was up and running prior to hibernation or while =
hibernation :-), everything will
>>>>>>>>>>>be fine. Also, what I can do was to un-plug and to re-plug the=
cam to the same hub. That's but
>>>>>>>>>>>no clue since I had to un-plug and to re-plug the cam each tim=
e. When I run the program after
>>>>>>>>>>>hibernation with no prior preparation the cams image(s ) will =
not show up, but a black square
>>>>>>>>>>>only and the green light on top of the cam does not flash
>>>>>>>>>>>
>>>>>>>>>>>Was any one used to the problem and can help?
>>>>>>>>>>>
>>>>>>>>>>>Thank you,
>>>>>>>>>>>Steve
>>>>>>>>>>
>>
>=20
>=20

Steve
Tue Apr 08 11:57:45 PDT 2008

I have had an other cam prior, which did not work either. It had a faulty joint that
couldn't keep the lens upright. Tthat's why I think it's something with the computer
sooner than with the cam.

"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OA0FzbamIHA.1368@TK2MSFTNGP02.phx.gbl...
Given that everything else comes back ok, I would hesitate to condemn
the chipset/motherboard.

Steve Miller wrote:
> Do you think it could be something with the chip set or there like?
>
> "Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:uudzi9ZmIHA.5368@TK2MSFTNGP04.phx.gbl...
> Try plugging directly into the PC, or contact MS tech support, or
> replace the camera.
>
> Steve Miller wrote:
>
>
>>That's a good idea since the cam was working already. :-) What else could I try out?
>>
>>I still hope that there was some setting I'm not used to now that would fix the issue.
>>
>>Steve
>>
>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:u6$FJsZmIHA.1280@TK2MSFTNGP05.phx.gbl...
>>If the green light is on after the PC is back up, try "find new hardware".
>>
>>Steve Miller wrote:
>>
>>
>>>When the program was running before hibernation the green light goes off while the computer
>>>goes to sleep ánd is back up when the computer was wake. The cam was 'off' while the computer
>>>was in hibernation mode.
>>>
>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:ezQXoGZmIHA.4196@TK2MSFTNGP04.phx.gbl...
>>>
>>>
>>>
>>>>Does the cam remain "on" though the hibernation period?
>>>>
>>>>Steve Miller wrote:
>>>>
>>>>
>>>>
>>>>
>>>>>The cam was not actually new hardware after hibernation. All the other usb devices are
>>>>>ok after hibernation and to function correct with no failure. Only the cam does not.
>>>>>
>>>>>The motherboard was from around '04, and I did install all the latest drivers but now do
>>>>>have the one installed Windows XP picked. All the same.
>>>>>
>>>>>Steve
>>>>>
>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:%23mka7zYmIHA.6032@TK2MSFTNGP03.phx.gbl...
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>>In hibernation the PC shuts off, and does not look for "new" things when powered back on. Perhaps "find new hardware" will
>>>>>>restore the cam after hibernation.
>>>>>>
>>>>>>Steve Miller wrote:
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>>Bob I, I think the hub was powered. I could plug the usb drive in the cams hub, it will work.
>>>>>>>
>>>>>>>I even could unplug the cam prior to starting the LifeCam program and plug it back into the
>>>>>>>same hub the program still off, the cam will work.
>>>>>>>
>>>>>>>It also works fine with a freshly booted up computer and after standby also. Only after
>>>>>>>hibernation it does not.
>>>>>>>
>>>>>>>Steve
>>>>>>>
>>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:eeugSZYmIHA.1912@TK2MSFTNGP04.phx.gbl...
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>>Perhaps plug it into a powered hub?
>>>>>>>>
>>>>>>>>Steve Miller wrote:
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>>Hi Bob I!
>>>>>>>>>
>>>>>>>>>Thank you for your reply. I did, but didn't help at all. Sorry I forgot to mention.
>>>>>>>>>
>>>>>>>>>Steve
>>>>>>>>>
>>>>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OHi7LZXmIHA.3780@TK2MSFTNGP06.phx.gbl...
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>>Go into Device Manager and in the Universal Serial Serial Bus section, go through the hubs,r-click on them, open
>>>>>>>>>>"Properties", then on the Power Management tab, UNcheck "Allow the computer to turn off this device........"
>>>>>>>>>>
>>>>>>>>>>Steve Miller wrote:
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>>Hello!
>>>>>>>>>>>
>>>>>>>>>>>I have got an Microsoft LifeCam VX-3000. the LifeCam dies not work after the computer was
>>>>>>>>>>>sent to hibernation and came back from it.
>>>>>>>>>>>
>>>>>>>>>>>I have got other devices sticking in other usb hubs that function with no problems (usb flash
>>>>>>>>>>>drive, a keyboard, external hard drive ).
>>>>>>>>>>>
>>>>>>>>>>>When the cam was up and running prior to hibernation or while hibernation :-), everything will
>>>>>>>>>>>be fine. Also, what I can do was to un-plug and to re-plug the cam to the same hub. That's but
>>>>>>>>>>>no clue since I had to un-plug and to re-plug the cam each time. When I run the program after
>>>>>>>>>>>hibernation with no prior preparation the cams image(s ) will not show up, but a black square
>>>>>>>>>>>only and the green light on top of the cam does not flash
>>>>>>>>>>>
>>>>>>>>>>>Was any one used to the problem and can help?
>>>>>>>>>>>
>>>>>>>>>>>Thank you,
>>>>>>>>>>>Steve
>>>>>>>>>>
>>
>
>

Bob
Tue Apr 08 12:28:24 PDT 2008

Try it on some other computer?

Steve Miller wrote:

> I have had an other cam prior, which did not work either. It had a faul=
ty joint that
> couldn't keep the lens upright. Tthat's why I think it's something with=
the computer
> sooner than with the cam.
>=20
> "Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OA0FzbamIHA.136=
8@TK2MSFTNGP02.phx.gbl...
> Given that everything else comes back ok, I would hesitate to condemn
> the chipset/motherboard.
>=20
> Steve Miller wrote:
>=20
>>Do you think it could be something with the chip set or there like?
>>
>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:uudzi9ZmIHA.536=
8@TK2MSFTNGP04.phx.gbl...
>>Try plugging directly into the PC, or contact MS tech support, or
>>replace the camera.
>>
>>Steve Miller wrote:
>>
>>
>>
>>>That's a good idea since the cam was working already. :-) What else co=
uld I try out?
>>>
>>>I still hope that there was some setting I'm not used to now that woul=
d fix the issue.
>>>
>>>Steve
>>>
>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:u6$FJsZmIHA.12=
80@TK2MSFTNGP05.phx.gbl...
>>>If the green light is on after the PC is back up, try "find new hardwa=
re".
>>>
>>>Steve Miller wrote:
>>>
>>>
>>>
>>>>When the program was running before hibernation the green light goes =
off while the computer
>>>>goes to sleep =E1nd is back up when the computer was wake. The cam wa=
s 'off' while the computer
>>>>was in hibernation mode.
>>>>
>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:ezQXoGZmIHA.4=
196@TK2MSFTNGP04.phx.gbl...
>>>>
>>>>
>>>>
>>>>
>>>>>Does the cam remain "on" though the hibernation period?
>>>>>
>>>>>Steve Miller wrote:
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>>The cam was not actually new hardware after hibernation. All the ot=
her usb devices are
>>>>>>ok after hibernation and to function correct with no failure. Only =
the cam does not.
>>>>>>
>>>>>>The motherboard was from around '04, and I did install all the late=
st drivers but now do
>>>>>>have the one installed Windows XP picked. All the same.
>>>>>>
>>>>>>Steve
>>>>>>
>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:%23mka7zYmI=
HA.6032@TK2MSFTNGP03.phx.gbl...
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>>In hibernation the PC shuts off, and does not look for "new" thing=
s when powered back on. Perhaps "find new hardware" will=20
>>>>>>>restore the cam after hibernation.
>>>>>>>
>>>>>>>Steve Miller wrote:
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>>Bob I, I think the hub was powered. I could plug the usb drive in=
the cams hub, it will work.
>>>>>>>>
>>>>>>>>I even could unplug the cam prior to starting the LifeCam program=
and plug it back into the
>>>>>>>>same hub the program still off, the cam will work.
>>>>>>>>
>>>>>>>>It also works fine with a freshly booted up computer and after st=
andby also. Only after
>>>>>>>>hibernation it does not.
>>>>>>>>
>>>>>>>>Steve
>>>>>>>>
>>>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:eeugSZYmI=
HA.1912@TK2MSFTNGP04.phx.gbl...
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>>Perhaps plug it into a powered hub?
>>>>>>>>>
>>>>>>>>>Steve Miller wrote:
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>>Hi Bob I!
>>>>>>>>>>
>>>>>>>>>>Thank you for your reply. I did, but didn't help at all. Sorry =
I forgot to mention.
>>>>>>>>>>
>>>>>>>>>>Steve
>>>>>>>>>>
>>>>>>>>>>"Bob I" <birelan@yahoo.com> schrieb im Newsbeitrag news:OHi7LZX=
mIHA.3780@TK2MSFTNGP06.phx.gbl...
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>&