Deploy Windows setting

Tutorials Win: Microsoft Windows Forum

- Previous
  - 1
    - How to change system hibernate to after 1 hour I need to enable hibernation mode from all my workstation, so I found out this command powercfg.exe, tell you how to enable this. but I can not find the right command to change to after 1 hours. I try to use powercfg /change "system hibernates" 60, but did not work, what is the right command for this. Thanks. Lillian Tag: Deploy Windows setting Tag: 324270
  - 2
    - Re Failure to boot in Safe Mode Further to my earlier messages:- My machine is running XP Pro SP3, and I recently changed my disc over to be connected via a PCI card "ITE IT8212 ATA RAID Controller". This was necessary as the motherboard does not support large discs in the bios. The system loads OK in normal mode, but will not load in Safe Mode. It gets to the state where I see a display of the drivers being loaded, but then drops back to the initial loading sequence. Further, if I try "last good", I'm pretty sure that a program error of some sort occurs (I see a quick flash of a blue screen with what looks like some error message), and again the machine drops back to the initial loading sequence. How can I diagnose these problems (I guess they are connected). I don't seem to have the option of a bootlog for the Safe mode, and, if I set it on in the boot init file, surely it will also be on for the normal load following, and overwrite the data I want to see! PS I have checked that I have the most recent driver for the board (dated 2007). Tag: Deploy Windows setting Tag: 324267
  - 3
    - bluetooth & windows Hi, my 2 1/2 old Laptop may or maynot have bluetooth but I dont know how to check. I already tried to read the 'help' section on it on my LT. Its fancy enough where is has wireless and all. My project is to try to pair my motorola razr (tmobile) through the bluetooth it has, to my windows xp pc; so I can transfer pictures and not have to send them one at a time via text, etc. I dont want to have to buy motorola software. So, how can i check for bluetooth on my windows pc? Tag: Deploy Windows setting Tag: 324247
  - 4
    - How to network with Win XP Home My company is planning to install a Windows 2003 server to use in HR system. We have 20 Win XP Home and 1 Win XP pro desktops. What must I do to ensure everything works- eg, I hear that we can't use Win XP Home for domain log in? Thanks for any advice. -Hung Tag: Deploy Windows setting Tag: 324241
  - 5
    - lost address in toolbar afetr sp3 update I had a spot on my toolbar where I could enter a website address and keep a history of them. After I ran the sp3 update it was gone and I can't see how to put it back on. It doesn't seem to be one of the options Anyone know how to fix this? Thanks Wayne Tag: Deploy Windows setting Tag: 324237
  - 6
    - Can not enter Hibernation Mode I just upgraded my computer from 1Gb RAM to 2Gb RAM. Hibernation mode used to work perfectly Now when I tried to enter the hibernation mode it starts the process and then comes back to the initial screen and displays an error that I do not have enough system ressources. I tried doing this with no software loaded and still no luck. Computer: Acer lnotebook OS: WIndows XP SP2 THanks for your help Chris Tag: Deploy Windows setting Tag: 324232
  - 7
    - Partition Magic access violation at address 0052dc00 in module PMagicNT.exe Read of address 00000008 --did anyone find a definitive sure for this error? Does PM8 have the same issues?? "access violation at address 0052dc00 in module PMagicNT.exe Read of address 00000008" I'm sitting here stalled reading a bunch of old strings describing what 'might' fix it.. Does anyone know a fix?!?!?? Tag: Deploy Windows setting Tag: 324230
  - 8
    - Windows Start Up - Activation Issue When I start up and come to the logon screen after I click on my user name a button comes up sayings Windows must be activated before i can logon. I click yes I want to activate (although I already have). After a minute a button comes up and says "Windows is already activated click ok to exit". I click ok and it takes me back to the logon screen. I click user name and this whole cycle starts over again. This is weird because I have been using this computer for a couple months with no problems. PLEASE HELP! -- Mike Tag: Deploy Windows setting Tag: 324229
  - 9
    - Netmeeting in Windows XP I have installed Winodws XP in ASUS EEE PC 900 notebook and found that the webcam cannot be used in the netmeeting. Can anyone please help? Ivan Tag: Deploy Windows setting Tag: 324227
  - 10
    - ALL LATEST DOWNLOAD AND UPDATE OF WINDOWS VISTA....... FREE DOWNLOADS FOR VISTA SUPPORTING SOFTWARES ONLY ON http://polticsinfs.blogspot.com/ Tag: Deploy Windows setting Tag: 324220
  - 11
    - WinSxS directory - what is it about I have just noticed this large(ish) directory under C:/Windows. Is this new (i.e. post SP3) or has it always been there? What is its function. My searches show that it is an innovation for Vista. However, it is definitely there in Win XP now, as a retro-fit? The only consolation - its does not gobble up as much space as the 6GB Vista equivalent. Tag: Deploy Windows setting Tag: 324219
  - 12
    - how to deactive hyplerlink in win word doc? whenever i save a web page with the help of word all the mail id saving with hyperlink i would like to deactive it. Somebody help me to do plz kayalvizhi Tag: Deploy Windows setting Tag: 324218
  - 13
    - Sound doesn't work after hibernation/sleep For some reason, when my computer comes out of hibernation or sleep mode, I can't get any audio to play through the speakers. It doesn't work on any audio player on the computer so it's something with the system I guess. I'm running windows XP with SP3. Thanks in advance! Tag: Deploy Windows setting Tag: 324217
  - 14
    - Missing text on buttons and task bar I have one piece of software from HP originally installed and ran perfectlly. I had to reinstall it sometime later and now when the main page of the software comes up the buttons to click on do not have text descriptions as previously. Also, the button on the task bar is blank. The little icon to the left on the task bar button is displayed . Also once you have gone past the main page, then the text of the buttons is back. My thought is some Windows setting got changed and affected this. Comments on what I should look at Tag: Deploy Windows setting Tag: 324210
  - 15
    - video card making noise I have an ATI Fire GL X1 AGP Pro graphics card and the fan is making noise. In fact it's been making noise now for almost a year, but it used to be just when I started it after it had been shut down for a while. Now, it's doing it constantly. If you can take a look at it on ATI's website, what do you think about taking the fan off and replacing it with a Zalman GPU fan. Or is it possible to do that with this card? Any help would be greatly appreciated. Thanks, attilathehun1 -- attilathehun1 Tag: Deploy Windows setting Tag: 324201
  - 16
    - Firewall problem. Hi. This problem had only developed recently, and I haven't changed anything I'm aware of. Can anyone throw some light please? XP pro, SP2, full updates. (Not seen SP3 at all). Dual core intel CPU, 2 gig ram, 8800GTX graphics. High spec home PC. I use Mozilla Thunderbird as my email client. It has been working perfectly under all updates for years. I use Zonealarm (free) as a firewall, and have a Sky router and broadband with it's internal firewall. Windows firewall is off. This has all been in place for a long time and nothing has been modified, moved of even had the dust wiped off. The problem is... I suddenly realised I hadn't had any mails for three days. I thought no one wanted to talk to me, so I checked with my provider to find all is OK there. Checked for updates on thunderbird, all up to date. Checked Zonealarms permissions, and thunderbird had nice big green ticks allowing access. Still no email. Disable zone alarm. Email flows. Aha, whats up with ZA I wonder? I reload it, delete the current entry for thunderbird and force it to ask for permissions again. They are granted, but still no mail through ZA. Shut ZA, mail flows. Hmmmmm. Uninstall ZA. Install another firewall, Agnitum Outpost. *IT* won't allow email either after granting permissions. Close it down, email flows. Hmmmmmmmmm. Uninstall Outpost, install ZA suite, the latest, paid for setup. Email asks for permission, but no mail! Arghhhhhhh. Shut it down, mail flows. So, what have these steps got in common? 3 firewalls, none will pass email even with permission granted, but when shut down it works ok. Not hardware related. Which software? ZA? Outpost? Or is it a windows thing? Has there been a security update that is interfering maybe? All other internet activity works OK. I can play online games at good pings with ZA in place, surf, usenet etc. Please, can anyone help? Thanks. Tag: Deploy Windows setting Tag: 324197
  - 17
    - hotkey for maximizing window's windows ? This is a multi-part message in MIME format. --------------030301010801020701050100 Content-Type: text/plain; charset=ISO-8859-1; format=flowed Content-Transfer-Encoding: 7bit What is the hotkey for maximizing XP window's windows? I have searched microsoft support database but haven't found... Like ctrl + c = copy ... --------------030301010801020701050100 Content-Type: text/x-vcard; charset=utf-8; name="comitter.vcf" Content-Transfer-Encoding: 7bit Content-Disposition: attachment; filename="comitter.vcf" begin:vcard fn:Majki Majk n:;Majki Majk adr;dom:;;;Zagreb email;internet:comitter@europe.com tel;cell:091/504-5311 note;quoted-printable:Cijenjena ponuda na e-mail kontakt!=0D=0A= Ozbiljne ponude molim!=0D=0A= Mo=C5=BEe i sms-om! x-mozilla-html:TRUE version:2.1 end:vcard --------------030301010801020701050100-- Tag: Deploy Windows setting Tag: 324189
  - 18
    - microsoft.public.windowsxp.basics folders I presently subscribe to just this Microsoft newsgroup. Whenever I open its folder, the highlighted number (in brackets) after the group's name, which shows how many messages are unread), will often not relate to the actual unread messages. For example, the highlighted number can be 24 but there can be as few as 4 or 5 actual unread messages. Sometimes, when there are no actual unread messages, there is a highlighted number showing. If I close the folder and then immediately open it, the highlighted number will often change to a different number. Using the "Catch Up" facility does not stop this happening. It's no big problem, just annoying. Advice much appreciated. Joe Steele Tag: Deploy Windows setting Tag: 324176
  - 19
    - Startup message from System Configuration Utility I used "msconfig" to get rid of a "DevDtc2.exe" error message on startup. Now when I bootup I get the following: You have used the System Configuration Utility to make changes to the way Windows starts. The Sys Config Utility is currently in Diagnostic of Selective Startup mode, causing this message to be displayed and the utility to run every time Windows starts. Choose the Normal Startup mode on the General tab to start Windows normally and undo the changes you made using the Sys Config Utility. Does this mean there is something wrong with my computer or should I just choose "Normal Startup" on the General Tab? Thanks in advance. Tag: Deploy Windows setting Tag: 324173
  - 20
    - Uninstalling SP3 The sequence is like this: I installed SP3 and had no trouble doing so, or any observed irregularities thereafter. Then HP told me to upgrade the ATI BIOS in my Compaq Presario, and I did. Now the bad news: Some of the USB ports are now invisible, and HP and AMD say that's because I never upgraded to .NET Framework 2.0. I had 2.0 a while back and uninstalled it because of incompatibility with other software. It seems there's no way to live stably in this electronic world. I pulled one of my pre-SP3 clones into service, and it works with the old BIOS and I'm thinking of uninstalling SP3 from my Master Drive, along with the 'upgraded' BIOS. In truth, my system was not broke, and it didn't need fixing with either SP3 or the upgraded BIOS. So my question is, is there a safe, convenient, reasonable way to uninstall SP3? I see it in Add/Remove Programs...is that all there is, just Remove it there? Will that put me back just as XP was before I installed SP3? Tag: Deploy Windows setting Tag: 324171
  - 21
    - Draging item into folder opens that folder. I don't want it too I'm organzing HUNDREDS of graphics on my machine in Windows Explorer. I created basic folders with titles to organize them into. Now I am finding my old folders that hold my graphics and am dragging them into the newly created folders. Problem is ever time I drag one over, the new folder automatically opens up to display all the files in it. Is there a way to stop that? I have to close the folder every time because it then pushes my other folders below out of sight. Is it possible to force folders to NOT open when dragging items or folders into them via Windows Explorer? Thanks so much! Nancy Tag: Deploy Windows setting Tag: 324164
  - 22
    - I have starzplay and Zune downloaded, but they will not play. Help I have downloaded from Verizon, starzplay. And I just bought a Zune. I have downloaded starzplay since June 5th. And cannot get it to play. An error message comes up saying the starz tray has encountered a problem and needs to close. I have talked with verizon techs, starzplay people, and have numerous trouble tickets waiting... no luck. Then with my new Zune, last night I installed the software, then to my amazement, it said that it is finished installing and then I went to sync, and the error message came up and said that Zune has encountered a problem and needs to close. These programs have to be related somehow, I am so frustrated. Thank you in advance for the help. -- diana Tag: Deploy Windows setting Tag: 324163
  - 23
    - Part of my Update keeps failing... Please email me at onlyvalgirl77@yahoo.com if you can help me out of this predicament. My automatic update pops up and all night long every time I click to install it will say it can download the following....Please help!!! Security Update for Windows XP with Windows Media Format Runtime 9.5 (KB923689) Cumulative Security Update for Internet Explorer 6 for Windows XP (KB950759) Security Update for Windows XP (KB950762) Security Update for Windows XP with Windows Media Format Runtime 9.5 and 11 (KB941569) Security Update for Microsoft .NET Framework, Version 1.1 Service Pack 1 (KB928366) Update for Windows XP (KB942763) Security Update for Windows XP (KB951698) Windows Internet Explorer 7 for Windows XP Windows Malicious Software Removal Tool - June 2008 (KB890830) Tag: Deploy Windows setting Tag: 324157
  - 24
    - M/Bd Sound My drivers on my mother board for the 'onboard' sound keep disappearing. I have to put the M/Bd Cd back in and reinstall. This happens quite a lot. M/Bd L7VMM2 Socket A. I have had this board for a few years now and never given trouble like this before. I have just reformatted the drive and reinstalled XP but it is still happening. I tried a Sound card I had and that worked ok but it altered all my Capture Card installation and rendered that inoperable. As it's a new install I wouldn't expect any viruses or spyware. Any help please. Tag: Deploy Windows setting Tag: 324152
  - 25
    - Monitor won't start, stays yellow on LED I changed my motherboard battery and it turned out it was dead, because the PC wouldn't fire up at all, just dead. When I went through everything you could think of, reseating the RAM, checking the power supply, changing the video card, changing the hard drive, changing the monitor and finally taking the heatsink and fan assembly off , cleaning it and reapplying the arctic silver, it turned out to be the motherboard battery. I forgot completely about that. But, when I finally replaced it and then fired it up, the monitor stayed yellow in the LED. I changed the jumper on the motherboard over to default, or to the other prong, whatever you want to call it, it has 3 prongs and I changed it over from 1 to 2 or from 2 to 3 whatever. When I did that the PC didn't even fire up. Nothing! When I changed it back to the original position it fired up, but the same problem of the monitor not working. Now there was progress because nothing was happening when you pushed the power button. Now you get the fans moving and the hard drive spinning or getting warm. Maybe it's the hard drive? I did check the hard drive and replaced it with another one. I'm going to try a new hard drive that hasn't been used before and give that a shot. One thing, if you change the motherboard battery and then you have problems you should be able to adjust the jumper on the motherboard to default and then switch it back. Even the tech at Dell said to do that and it would be ok. I guess not. Well, the motherboard is a M7VIG 400 that supports AMD processors and the chip is an AMD Sempron 2200. I think it's the motherboard that's screwy. Any help will be greatly appreciated. Thanks, attilathehun1 -- attilathehun1 Tag: Deploy Windows setting Tag: 324148
- Next
  - 1
    - Where the new window will open I use two monitors for an expanded desktop. How do you control where new windows will open. Often I'll be using explorer to look at something, and click a link to open a new window, and it pops up on the other screen, or when doing repetitive work, the new window will begin to creep towards the edge of screen 1 after several repititions of opening and closing, to eventually begin appearing, half on one screen and half on another. Is there a setting or technique I can use to anchor where the new window opens, so it's consistent time after time? RES Tag: Deploy Windows setting Tag: 324143
  - 2
    - notepad opens Desktop.ini file on Windows startup! How to eliminate that? jas Tag: Deploy Windows setting Tag: 324137
  - 3
    - Standby Insomnia I usually put my WinXP Home desktop into stanby when I won't be using it for a few hours. i do so using Start | Turn off Computer | Standby The computer goes to sleep. But occasionally it will spontaneously wake up after a few minutes. Any explanation? Note that I have Power Options set as follows: Turn off Monitor 10 minutes Turn off Hard Drive 15 minutes System Standby 15 minutes Hibernate is not enabled -- PT Tag: Deploy Windows setting Tag: 324129
  - 4
    - Windows XP and Zune I cant believe I spent 250$ on a Zune and it's not compatible with my Windows XP. Now for it to work I have to buy a whole new operating system at an additional 120$. Way too much hassle for something that should work with the OS I have. Thanks Microsoft! Next time label your boxes better. Tag: Deploy Windows setting Tag: 324128
  - 5
    - System Restore disabled on reboot I am running XP Home with SP3. I have a problem that existed before installing SP3.. When I rebooot the PC and goto System restore, I get the prompt that tells me that SR has been turned off. I go to the SR screen and enable it, create a restore point and it all works fine. When I reboot the PC, SR gets switched off somehow and it goes back to the SR turned off message. I have inspected logs using event viewer and after reboot their is an entry " Event 116 System Monitoring disabled on reboot". This happens every time I reboot. Any ideas appreciated Tag: Deploy Windows setting Tag: 324123
  - 6
    - Schedule task to open Word document I have scheduled to run Word in the morning. However, how do I tell the Word to open a particular Word document when it starts up at that time? Tag: Deploy Windows setting Tag: 324111
  - 7
    - CMOS after changing mobo battery Ok, I found out all I needed to do was to change the 3 volt 2032 motherboard battery and all would have been ok. Instead I reseated the RAM sticks, changed the power supply, changed the video card, changed the IDE parallel straps, changed the monitor, changed the hard drive, and finally took out the motherboard and removed the heatsink and fan asembly off the CPU chip and checked the chip out. After all that it turns out the reason the PC stopped working was the little 3 volt battery on the motherboard. It worked again for a little while, maybe a day after I changed the monitor. Just like a flashlight that is going dead, after you sit it for a while the next day you will get some power and it will work for a while and then dim out. Tell tail signs of battery failure. By accident I was checking this new battery checker device that I bought from Home Depot and I needed batteries to check to see if the settings worked and found out the battery wasn't working. Ok, now lets get to the CMOS. There is a CMOS jumper on the motherboard that I see. What do I need to do to the jumper or do I need to physically do anything on the mobo or just go into BIOS and configure something there? Any help will be greatly appreciated. Thanks, attilathehun1 -- attilathehun1 Tag: Deploy Windows setting Tag: 324102
  - 8
    - Drive mapping syntax I use logon scripts to map drives for select users. Is there a way I can format what the user sees? I don't want the actual drive letter or path to show up in Explorer, just the folder/mapped drive name. I know I can do this if I map it manually, but want to continue to use logon scripts. Tag: Deploy Windows setting Tag: 324094
  - 9
    - Safe Mode Problem I am using windows XP SP3 via a disc on a PCI card. Whilest this boots and loads perfectly happily in normal mode, it fails to load in Safe Mode. Is there anything I can do to get safe mode working via this card? It is not necessary at the moment, but perhaps in the future? PS I notice that there is a driver associated with this card called "iteraid.sys". Tag: Deploy Windows setting Tag: 324091
  - 10
    - DevDtct2.exe error on startup in Windows XP recently performed a non-destructive recovery on my Win XP computer. Now on startup, I get the following error message: DevDtct2.exe - Unable to locate component This application has failed to start because OdiAPI.dll was not found. Re-installing the application may fix this problem. Any help would be most appreciated. Thanks in advance. Tag: Deploy Windows setting Tag: 324087
  - 11
    - Putting icon on desktop on pda Sorry, couldn't find a better place to ask this question. How can I put program icons (or titles) on the desktop on a pda using Windows CE Mobile 6. I have an ASUS MyPal A639 pda. Many thanks. -- Don Vancouver, USA Tag: Deploy Windows setting Tag: 324073
  - 12
    - Can't close application with Alt+F4 or the X I was wondering if anybody might happen to know what's going wrong here: When a co-worker tries to close her program by clicking the X in the top right it doesn't do anything, and Alt+F4 won't work either. There is no error message just doesn't respond to either one of the actions above. Thanks! Tag: Deploy Windows setting Tag: 324072
  - 13
    - old update problem? XP Pro SP 2 I just looked over my update log and found one failure from some time back, altho I didn't see a failure notice at the time. That was Microsoft .NET Framework 1.1 Hotfix (JB928366}. On Microsoft I saw that quite a few people had that problem, and the solution was to download it manually (address given) and install it manually. With Framework 2 installed in the intervening time, should I or should I not download and try to install the old failed update? Would installing the old update backlevel something so that I would need to reinstall Framework 2? JimL -- It's been said Pelosi should be slapped silly, but that condition has been reached without the slapping. Tag: Deploy Windows setting Tag: 324067
  - 14
    - USB Port not working in XP IBM Netvista, latest BIOS, XP-P with latest patches/updates. Symptoms appear on SP2 as well as SP3. All of a sudden I lost my USB Ports on the computer. I think it happened because of a power failure, but not sure. I hear the pacifier beep in the speaker when connecting my mouse or thumb drive, however, neither responds. the mouse LED lights, but cursor remains in the middle of the screen. I don't have a USB keyboard so I can't test the USB connection during BOOT. I suspect it will work. The mouse will not be recognized until the OS loads. The thumb drive makes the same beep, but I never see it displayed as a removable drive or any drive for that matter. The PS2 mouse works just fine. Using a USB to PS2 adaptor does not work either. Any ideas?? I'm stumpbed on this one. The MSKB isn't of any help so far. Thanks Tag: Deploy Windows setting Tag: 324065
  - 15
    - Crypt32 Error Hi, I'am getting a "Crypt32" error in 'Event Viewer', see below Windows XP SP3, IE7, OE6 Event Type: Error Event Source: crypt32 Event Category: None Event ID: 8 Date: 6/10/2008 Time: 12:40:35 AM User: N/A Computer: HOME-E4BC337052 Description: Failed auto update retrieval of third-party root list sequence number from: <http://www.download.windowsupdate.com/msdownload/update/v3/static/trustedr/en/authrootseq.txt> with error: The specified server cannot perform the requested operation. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. There is in additional info in Microsoft Help and Support Center. Any pointers from anyone will be appreciated. Tag: Deploy Windows setting Tag: 324054
  - 16
    - Battery failure Would your computer stop working all of a sudden one day if the motherboard battery, the 2032 organize battery I think, stops working? The computer worked when I changed the monitor but then it stopped working shortly after that. Then it didn't matter what monitor I tried, it just wouldn't fire up. I checked everything almost, reseated the RAM, checked the power supply, tried another video card, checked the hard drive, used different parallel straps. I mean I went through all I could think of, except the motherboard battery. By accident I discovered that it wasn't working. Do you think that could be the problem? Is that a common problem of a PC going on the blink? Would it start up after a rest and then finally shut down? It seems like the battery on my flashlights get better once they aren't on, but once you turn the flashlight back on, the flashlight dims out. I'm thinking about putting the whole PC back together now and trying out a battery that I know works. Ok, this is the truth. I took out the battery and changed it with another one and I think the one I changed it with was bad. I'm not sure, but I know I did change the battery. I was trying out my battery tester and found out the right option on the tester to test 3 and 1 1/2 volt batteries. So, I'm not sure if the original battery I took out was good or bad. That's why I'm asking if it's a common problem. Any help would be greatly appreciated. Thanks, attilathehun1 -- attilathehun1 Tag: Deploy Windows setting Tag: 324050
  - 17
    - NTFS Cluster size Hello, Windows XP SP3, NTFS File system on C: drive. How can I determine the cluster size of the NTFS file system on my computer? This request is based upon this information: "Make sure the partitions are aligned to 4K boundaries or else you may end up with 512 bytes clusters". Thanks In Advance Tag: Deploy Windows setting Tag: 324049
  - 18
    - restoring Windows XP backup files: label is missing I have a backup file that I made using the Windows XP backup utility, but the label for it is missing and so Windows Backup can't extract and restore the data. Does anyone know of any fixes for recreating backup labels? Thanks-- Tag: Deploy Windows setting Tag: 324045
  - 19
    - Permissions and file access I am using XP Pro. I recently had to reformat my hard drive. In preparation I did a backup of selected files and folders using Nero 8. After reinstalling Xp, I did a restore with Nero. I noticed during the process, a number of files received the following: System error 1307: This security ID may not be assigned as the owner After the restore, I click on some of the folders and I get an "Access Denied" error. Ihad the same results using XP backup and restore utility. I am the only user with administrator privileges. I use two computers in a home wireless network with file sharing. How can I correct this problem. Tag: Deploy Windows setting Tag: 324041
  - 20
    - Start menu Everytime I click on 'Start' it tells me there are new programs installed. there are no new programs installed to my knowledge ( well sometimes there are). It then goes away for a while but returns all the time. Any help please Tag: Deploy Windows setting Tag: 324037
  - 21
    - Chinese version software install - wrong display One of my pc's runs Windows xp English version (SP3). The pc has beeen setup with chinese fonts and the regional setting is Chinese (Taiwan). I can enter Chinese texts and display them in say, Microsoft Word without any problems. Now I want to install Corel Draw (it was sold to my son as education version), Chinese version onto the pc. When the installation CD is inserted into the Drive, it starts the autorun and brings up the installation screen. However, the display text shows many 'question marks' instead of the normal Chinese characters. What do I miss out? Tag: Deploy Windows setting Tag: 324036
  - 22
    - How to expand the windows tab-bar underneath ...? This is a multi-part message in MIME format. --------------080009080209060002010802 Content-Type: text/plain; charset=ISO-8859-1; format=flowed Content-Transfer-Encoding: 7bit How to expand the windows tab-bar underneath so to get two rows for applications, programs etc ? I mean on the tab-bar next to quick -launch bar ? Thanks in forward! --------------080009080209060002010802 Content-Type: text/x-vcard; charset=utf-8; name="comitter.vcf" Content-Transfer-Encoding: 7bit Content-Disposition: attachment; filename="comitter.vcf" begin:vcard fn:Majki Majk n:;Majki Majk adr;dom:;;;Zagreb email;internet:comitter@europe.com tel;cell:091/504-5311 note;quoted-printable:Cijenjena ponuda na e-mail kontakt!=0D=0A= Ozbiljne ponude molim!=0D=0A= Mo=C5=BEe i sms-om! x-mozilla-html:TRUE version:2.1 end:vcard --------------080009080209060002010802-- Tag: Deploy Windows setting Tag: 324031
  - 23
    - Failure to install Downloading from windowsupdate website since the automatic update is not working either, I check several updates that I need, the install starts several seconds pass and get the message "failure to install....." what do I need to do? Windows XP Pro SP2 Thanks Tag: Deploy Windows setting Tag: 324026
  - 24
    - changing file system Hi, I've re-installed Windows XP on my laptop with four drives. Earlier, the file system is FAT32. During re-install, I've formatted the system drive (C:) to NTFS. All other drives are still FAT32. How can I change the rest of the drives to NTFS without losing my files/data on those drives. Thank you. -- Sreedhar Tag: Deploy Windows setting Tag: 324018
  - 25
    - Convert Recycle Bin To Dat Hi All, I accidently dragged my recycle bin with the right mouse button and the popup said "Convert To DAT Format" What is this? Thanks Chad Tag: Deploy Windows setting Tag: 324013

Hi all,

How could I configure/deploy/pre-set the same set of "View" settings
in "Folder Options" to all users/all new users in a XP Pro machine?
Should I manually tweak the registry or should something like the
group policy be used? If so, what are the respective registry keys or
which mmc should be use. Thanks for advise.

Top

RE: Deploy Windows setting by Marty

Marty
Thu Aug 21 01:18:00 PDT 2008

already any answers? I've got to install 16 PC's and would like to know how
to copy the settings of taskbar etc.

Top