thread creation exception

Tutorials Win: Microsoft Windows Forum

- Previous
  - 1
    - Bluetooth bthcsr.dll problem with ActiveSync and virtual COM connection idle/overflow Dear all, I try to establish bluetooth activeysnc connection between a WinCE.Net 4.2 platform and PC. On WinCE.Net 4.2 platform, when i plug in SocketCom Bluetooth CF card (Socket-CF+_Personal_Network_Card_Rev_2.5-E3CE), bthcsr.dll is loaded and bluetooth manager able to scane bluetooth device around. When using Asui to make bluetooth activesync connection to PC, activesync connection dialog box is shown, "connecting -> User authenticated ->connected", then it disconnect immeadiately. If i use another SocketCom bluetooth CF card (Socket-CF+_Personal_Network_Card-6C76), bthsc.dll is loaded. with this driver, asui able to establish bluetooth activesync connection with PC. On the other hand, if I use the first socketcom bluetooth CF card (using bthcsr.dll) that i mentioned early to connect to GPS receiver, it able to retrive all Nmea message but this connection will some how idle after some time and no more data reveice from GSP receiver. We need to disconnect virtual com and re-register again. If I use the second socketcom bluetooth CF card (using bthsc.dll), it able to retreive data from bluetooth GPS receiver constanly and never idle. Is anyone there which using bthcsr.dll for their bluetooth hardware encounter this problem before? Thanks for your help in advanced. Best Regards, Francis Tag: thread creation exception Tag: 53761
  - 2
    - CEDB from ADOCE - what's needed? Hi all, I'm trying to make an ASP page use ADOCE to connect to a CDB database. Using eVC I made a small program to create a test .cdb file. That seems to work. I have my testdb.cdb file. However when I try to access from ASP, I get an error: "Error: The operating system on your device does not support all features. All features are supported in Windows CE for the Handheld PC version 3.0 or greater.\n" This is a CEPC built using Platform Builder 4.2, evaluation. Relevant part of the ASP page: <% Dim oConn On Error Resume Next Set oConn = CreateObject("ADOCE.Connection.3.1") oConn.ConnectionString = "data source = '\hard disk\testdb.cdb'" oConn.Open If Err.number <> 0 then Response.Write "Error: " & Err.description End If I have copied ADO onto the device and registered the DLLs: regsvrce adoce31.dll regsvrce adoxce31.dll regsvrce msdadc.dll regsvrce msdaer.dll regsvrce msdaosp.dll and indeed the CreateObject is now working. I can't see anything else needed... Thanks Aaron Tag: thread creation exception Tag: 53755
  - 3
    - GPRS/RAS connection Hi, Stuck on this problem for many days now. Using the core of the rasdial sample, we can dial our GPRS through the following RAS states: RASCS_OpenPort RASCS_PortOpened RASCS_DeviceConnected RASCS_AllDevicesConnected RASCS_Authenticate RASCS_Authenticated but then everything locks up. (including Telnet, FTP, Remote Desktop) Same result when trying with the AutoDial.exe sample program. Any ideas on what to try next? Thanks Andrew Tag: thread creation exception Tag: 53749
  - 4
    - media player and CF wakeUP problem. Hi We are using WinCE4.2 on Xscale platform with CF and DiskOnChip as a storage devices.Everything is working fine. The problem is when the system WakeUP from suspend. If a mp3 file stored in the CF is played using media player and the sytem goes to suspend state after wakeUP the file will be played for little time then after that WinCE will give an error saying "an error occured while playing (0x80070651)" and stops playing the song. After that if the song is loaded again it plays without any problem. Please Could any one help me soon to solve this problem. With Regards Akram Tag: thread creation exception Tag: 53748
  - 5
    - shell command hi all, i would like to know how to load any dll which is present in the image through the shell command. i tried using "loadext dllname.dll" on the command line. but it did not work out. is there any way for loading dlls runtime, or what are the requirments for loadext command to function properly. regards neo Tag: thread creation exception Tag: 53747
  - 6
    - About using Bluetooh. I have a pxa255 board, the system is wince.net 4.2. Want to add bluefunction through dongles using usb or BT com, but i 'm so puzzled here. Since there is no driver for CE.net provided with these products available(is there?), we have to develop drivers on our own. I took a look at the sample in PB, that has many files in the folder ,which one should be modified? My board had provided several dlls about bluetooth, seems to be the services needed except for the main driver. Don't know what Document to look up in, the spec made me astrayed. Would anyone direct me a way? And, my goal is to use BT GPS through the dongle, the most straight way is wanted, then what module alike should i choose? Thanks!! Tag: thread creation exception Tag: 53746
  - 7
    - Avoid debug message on serial line Hi all, I'm developing a real time application using WCE.NET 4.2. The application use serial ports (COM1-COM2 and others) for doing its work; debug message on serial line sometimes damage the protcol carried on it (normally on COM1 by KITL). Moreover using debug with eVC++ COM2 begin to transmit a message continuosly and get stuck (i.e. my application does not receive anything on COM2, otherwise if I run application without using eVC++ debug, COM2 work properly). How may I force debug to use only ethernet, or how may I disable debug using serial line ? Thanks in advance Andrea C. Tag: thread creation exception Tag: 53745
  - 8
    - what did I screw up? All of a sudden all my release builds now show this message on the debug console: . . . Explorer(V2.0) taskbar thread started. Explorer(V2.0) using old style message pump. . NDISPWR:: Found adapter [LAN90001] . and I have the build text (Microsoft Windows CE.NET v4.20 ...) accross the display (like I use to get with only the debug builds). This just started happening. my build options settings for the release have not changed (I only have Enable Eboot space in memory checked for Release). what happened and how can I repair?? I tried doing a deptree build and a "blddemo clean" to no avail. Help!!?? Tag: thread creation exception Tag: 53733
  - 9
    - UNALIGNED macro?? I while back there was a post about the use of memcpy and how it can get you into data access problems (ARM4VI). I sort of understand the problem. Steve offered two solutions: Use the #pragma function(memcpy) or the macro UNALIGNED. I understand that the #pragma function "undoes" the inlining but I would like to know why this works? Also what does the UNALIGNED macro exactly do? Where is it defined? Tag: thread creation exception Tag: 53729
  - 10
    - Is there a way to simulate bootloading on desktop computer ? Hi all I've read the documentation of pb but I can't find information about this. So I wonder if it's possible to do. I would like to know if there is a way of simulating the bootloading process on a development computer, for verifying before writing the bootload disk on the real platform ? This verification would test : the autoexec.bat + config.sys files the 'loadcepc nk.bin' procedure thanks Tag: thread creation exception Tag: 53725
  - 11
    - How to add BSP to Platform Builder Hi, I got a MC9328MX1 ADS board and it binary BSP. I want to know how can I use this BSP in Platform Builder? Thanks! Regards, Rover Tag: thread creation exception Tag: 53722
  - 12
    - How to make the TV OUT fit whole screen ? Dear all: Here I use TVIA 5000 display driver and make use the TVOUT function. What trouble me is that the TV out cannot fit the whole TV screen right.Neither it is bigger or smaller. Is there any method to make it fit well ? What I use is 640x480 configurations. Thanks a lot! Jack. Tag: thread creation exception Tag: 53718
  - 13
    - [Q] About Ethernet Downloading. Dear, I'm very new at PB 4.2 and PB itself. So next questions are very simple. I'd like to try my old Pentium machine to change Windows CE.NET machine. Is it possible to make normal x86 based PC to CE.NET machine? I've just made x86 based OS image, I'd like to download it via Ethernet Connection. I think I'd follow the direction on PB 4.2 Help. But It doesn't work. 1. I'd made Boot Floppy Disk and insert it on the remote machine. 2. I'd alleady made x86 based OS image, and on the Target->Configure Remote Connection, choose Ethernet both of Download and Kenel Box. 3. On the Target Menu -> Choose Download/Initialize. 4. After that I'd turn on the remote machine. After the booting on the remote machine, It has just following message. "Jumping to 0X0013A420" And PB 4.2 machine still waiting for connection. Is it wrong from the start? I don't know how can I download the OS image. Any comment would be great helpful. Thanks. Tom Tag: thread creation exception Tag: 53717
  - 14
    - how to get rid of these errors?? when I do a "blddemo clean" I get all these errors... how do I get rid of them and why are they caused? c:\wince420\public\wceshellfe\oak\inputmethods\korean\msimk\im.h(37) : error C2504: 'IInputMethod2' : base class undefined c:\wince420\public\wceshellfe\oak\inputmethods\korean\msimk\im.h(66) : error C2061: syntax error : identifier 'IIMCallback2' c:\wince420\public\wceshellfe\oak\inputmethods\korean\msimk\im.cpp(173) : error C2143: syntax error : missing ';' before '*' c:\wince420\public\wceshellfe\oak\inputmethods\korean\msimk\im.cpp(173) : error C2501: 'g_pIMCallback2' : missing storage-class or type specifiers c:\wince420\public\wceshellfe\oak\inputmethods\korean\msimk\im.cpp(2395) : error C2440: '=' : cannot convert from 'class CInputMethod *const ' to 'struct IUnknown *' c:\wince420\public\wceshellfe\oak\inputmethods\korean\msimk\im.cpp(2643) : error C2065: 'pIMCallback2' : undeclared identifier c:\wince420\public\wceshellfe\oak\inputmethods\korean\msimk\im.cpp(2644) : error C2448: '<Unknown>' : function-style initializer appears to be a function definition c:\wince420\public\wceshellfe\oak\inputmethods\korean\msimk\im.cpp(2658) : error C2065: 'IID_IInputMethod2' : undeclared identifier c:\wince420\public\wceshellfe\oak\inputmethods\korean\msimk\im.h(37) : error C2504: 'IInputMethod2' : base class undefined c:\wince420\public\wceshellfe\oak\inputmethods\korean\msimk\im.h(66) : error C2061: syntax error : identifier 'IIMCallback2' c:\wince420\public\wceshellfe\oak\inputmethods\korean\msimk\im.h(37) : error C2504: 'IInputMethod2' : base class undefined c:\wince420\public\wceshellfe\oak\inputmethods\korean\msimk\im.h(66) : error C2061: syntax error : identifier 'IIMCallback2' c:\wince420\public\wceshellfe\oak\inputmethods\korean\msimk\link() : error LNK1181: cannot open input file 'obj\ARMV4I\retail\im.obj' c:\wince420\public\wceshellfe\oak\inputmethods\korean\msimk\im.h(37) : error C2504: 'IInputMethod2' : base class undefined c:\wince420\public\wceshellfe\oak\inputmethods\korean\msimk\im.h(66) : error C2061: syntax error : identifier 'IIMCallback2' c:\wince420\public\wceshellfe\oak\inputmethods\korean\msimk\im.cpp(173) : error C2143: syntax error : missing ';' before '*' c:\wince420\public\wceshellfe\oak\inputmethods\korean\msimk\im.cpp(173) : error C2501: 'g_pIMCallback2' : missing storage-class or type specifiers c:\wince420\public\wceshellfe\oak\inputmethods\korean\msimk\im.cpp(2395) : error C2440: '=' : cannot convert from 'class CInputMethod *const ' to 'struct IUnknown *' c:\wince420\public\wceshellfe\oak\inputmethods\korean\msimk\im.cpp(2643) : error C2065: 'pIMCallback2' : undeclared identifier c:\wince420\public\wceshellfe\oak\inputmethods\korean\msimk\im.cpp(2644) : error C2448: '<Unknown>' : function-style initializer appears to be a function definition c:\wince420\public\wceshellfe\oak\inputmethods\korean\msimk\im.cpp(2658) : error C2065: 'IID_IInputMethod2' : undeclared identifier c:\wince420\public\wceshellfe\oak\inputmethods\korean\msimk\im.h(37) : error C2504: 'IInputMethod2' : base class undefined c:\wince420\public\wceshellfe\oak\inputmethods\korean\msimk\im.h(66) : error C2061: syntax error : identifier 'IIMCallback2' c:\wince420\public\wceshellfe\oak\inputmethods\korean\msimk\im.h(37) : error C2504: 'IInputMethod2' : base class undefined c:\wince420\public\wceshellfe\oak\inputmethods\korean\msimk\im.h(66) : error C2061: syntax error : identifier 'IIMCallback2' c:\wince420\public\wceshellfe\oak\inputmethods\korean\msimk\link() : error LNK1181: cannot open input file 'obj\ARMV4I\retail\im.obj' Tag: thread creation exception Tag: 53714
  - 15
    - Building WINCE OS Image for ARMV4I processor Hi, Anybody help me out in building a WINCE OS image for ARM processor. Thanks in advance, Regards, Sathish. R Tag: thread creation exception Tag: 53706
  - 16
    - USB Joystick driver I am trying to get a USB joystick/gamepad running on a Windows CE .NET device. Does anyone know if one is available for purchase? If not, do I buy the Platform Builder to develop one myself? Thanks Tag: thread creation exception Tag: 53703
  - 17
    - Platform Manager API / Streams I am trying to get create a stream between an executable on the PC and one on the handheld device using the IPMConnection::CreateStream() function. I was following the "How to Create Remote Tools for Windows CE .NET" guide in MSDN and using the Remote Time Viewer test app as a reference. However the guide says TimeViewer is using IPMConnection but it isn't, at least the version I have isn't; rather it uses IConnection. There seems to be 2 similar hierarchies of interfaces defined in cemgr.h, IRemoteDevice vs IPMRemoteDevice, IConnection vs IPMConnection etc. They differ in minor ways, so for example IPMPlatformManager has a GetPlatform where you can pass the name, but IPlatformManager only has one for the GUID, so to search it by name you have to enumerate the platforms and ask each their name. Anyway, IConnection::CreateStream() takes the stream GUID as an actual GUID but IPMConnection::CreateStream() takes it as a BSTR - "bstrHostId [in] GUID of the host. " I wasn't sure how I was supposed to pass the GUID as a BSTR, so I tried doing it like this: // {1B140018-0ABD-4b4e-99B8-8F8A635F4BB3} DEFINE_GUID(CeRunnerStreamGuid, 0x1b140018, 0xabd, 0x4b4e, 0x99, 0xb8, 0x8f, 0x8a, 0x63, 0x5f, 0x4b, 0xb3); #define CeRunnerStreamGuidAsStr L"1B140018-0ABD-4b4e-99B8-8F8A635F4BB3" ... IPMConnectionStream *piIPMConnectionStream = 0; BSTR bstrGuid = SysAllocString(CeRunnerStreamGuidAsStr); hr = piIPMConnection->CreateStream(bstrGuid, 0, piIPMConnectionStream); if (FAILED(hr)) { wcerr << L"Failed to create stream " << hr << endl; return -1; } Unsurprisingly, I get an HRESULT back of 0x80070057 "The parameter is incorrect.", so clearly this isn't the right way to do it. Could someone explain to me what the correct way to do this is? Why are there 2 similar sets of interfaces in cemgr.h? Also, since TimeViewer uses the Ix rather than IPMx interfaces, does that mean the example code in the TimeViewerCe.exe to create the device-end of the stream won't work if I create the stream on the PC-end using IPMConnection? Thanks in advance, Dave Tag: thread creation exception Tag: 53702
  - 18
    - Layered Service Provider Has anybody been able to get the sample LSP that comes with platform builder to work on Pocket PC? I could use some hints if anybody has succeeded. Tag: thread creation exception Tag: 53695
  - 19
    - How to clean object files in a custom folder with PB 4.2? Hi, whenever I add a feature to the platform which will be build outside the _WINCEROOT folder, a clean does not delete the object files created by a previous build. For example, my _WINCEROOT folder is D:\WINCE420 and I have a feature with the following build method: BuildMethod ( Step ( BSP ) CPU ( "x86" ) Action ( '#BUILD(SOURCES,"D:\Projects\OtherLocation")' ) ) the object files are created at D:\Projects\OtherLocation\obj\x86\[debug|release] and are still there after a "Clean". If I move the project to somewhere beneath the _PROJECTROOT folder, the object files seem to be deleted after a platform build (I couldn't find them after a platform build, but the target exe file is successfully created). Where does PB 4.2 create the object files and how can I obtain that the object files are created in that folder even if the source path is anywhere outside the _WINCEROOT folder? Thanks in advance. Markus Bauer Tag: thread creation exception Tag: 53689
  - 20
    - how can i transfer files or applications from PC to CEPC? i have built CEPC which can boot from CEPC`s hard disk.However, how can i transfer other files or applications from PC to CEPC`s hard disk? i want to transfer through COM by ActiveSync,but i find ActiveSync can`t detect CEPC. In pb,serial com driver is com16550,is it right? OR what should i do? thanks for your reply! Tag: thread creation exception Tag: 53687
  - 21
    - smdk2410 usb problem! cannot add the keyborad and mouse. hi everyone! am using smdk2410 , want using the usb host as keyboard and mouse port, after adding the usb host support and the HID from the core os service and download to the device. it print out this and stop. anyone can explain this, thanks in advance. 160 PID:afeebe72 TID:afeebe4e OEMSetRealTime: 170 PID:afeebe72 TID:afeebe4e OEMSetRealTime(register): 720 PID:afeebe72 TID:afeebe4e FMD::FMD_Init 980 PID:afeebe72 TID:afeebe4e FMD::FMD_OEMIoControl = 0x71c24 1130 PID:febdd4a TID:febd536 Prescaler:2 1140 PID:febdd4a TID:febd536 384 clock 1200 PID:febdd4a TID:febd536 USB:OhcdPdd_Init 1240 PID:febdd4a TID:febd536 ++InitializeOHCI Tag: thread creation exception Tag: 53685
  - 22
    - How could i store my datas in flash? In smartphone, there is a dir in which the files copied will be automaticly saved in flash. What about in wince.net on pda? i want to save custom data into rom, and how could it be achieved? prequiste: no bsp available thus image rebuilding unviable. 1.use jflash to add some .bin file right follow nk.bin 2.save them on storage card, but need to mamually install driver each time the board resets. 3.there....is still some sorts of dir, flashable~ 4....don't know Anyone do please give me some suggestion ? most appreciated:) Tag: thread creation exception Tag: 53681
  - 23
    - download connection instance fail Hi all, For the time saving with multiple working images I usually worked with at least two platform builder in the same screen at the same time. so during download image to target I used one active connection over ethernet. there was no problem for a while. however, suddenly I got fail with downloading image because of the active connection service get out of the control and I couldn't delete it because the all of the configuration property of that active connection is grayedm. it would be done by my fault in multiple platform enviroment. I guess it is cause of that active connection still using even I don't use now.... how can I recover that connection or delete it for new active connection ? BR. Tag: thread creation exception Tag: 53680
  - 24
    - SDIO Driver Hello world, Hope anyone can help me figuring this out: I've to develop an SDIO driver for a hardware that's is being designed at the moment. I've been asked to develop the relevant driver for PPC windows mobile 2003. Here is my questions : Does PocketPC 2003 come with a SDIO driver such that the SDIO card will work on any PocketPC 2003 device with SDIO compatible SD slot? My understanding is that so far one had to buy the BSQUARE SDIO now! kit for peripherals and write its own driver and then distribute it with the card ... Boring and Expensive! I read on the BSQUARE website that the Windows CE .NET release will indeed integrate the SDIO driver. Is that true? Does this apply for the current Pocket PC 2003 release already? I terms of software, what does it means? - should i develop just a lib? - should i develop a new stack on a already build SDIO driver? - anything else? What kind of tool i need (just eVC, platform Builder, ...)? This is a bit fuzzy for me. Thanks a lot for your help ----------------- liooil * remove _NOSPAM_ in my adress if you wish to mail me directly * Tag: thread creation exception Tag: 53678
  - 25
    - Is there a list of (not) working USB HID devices? Hi, in article http://support.microsoft.com/default.aspx?scid=kb;en-us;320921 it is stated that there are keyboards or other input devices which don't work with WCE4.1 USB driver. I wonder is it true also for WCE 4.2? Will that be fixed in WCE 5.0? Also, is there a list of HID devices that work perfectly, and a list of devices that do not work? I'm asking that because we must say to customers which HID devices are supported. Or MS perhaps expects from WCE developer to test all available keyboards and mice? Thanks in advance, Dusko Stajic Tag: thread creation exception Tag: 53674
- Next
  - 1
    - Problem writing to directly flash while IPSM running Hi all, We have the need to update one erase block in our FLASH RAM to record some data permanently. We are running Windows CE.NET V4.2 on a PXA255 processor with IPSM V3.6 managing the Flash File system. The documentation from Intel refers to "PSM Flash Control Semaphore" to communicate to the IPSM software that you want to access the flash. I originally planned to implement this write function in the OEMIoControl() function but was stopped because I could not access the Win32 Mutex() functions from the HAL. So, I moved the function into a device driver and initiate the write by opening the device and calling the DeviceIoControl() function. Having implemented, I tested it on a target device using the Platform Builder and it seemed to function correctly. I then moved it to a release build and calling this function causes the Windows CE operating system to completely lock up. I suspect that the debug build works because the OS is executing out of RAM. The OS build is XIP from the FLASH RAM. But I thought that the design of the Intel chips allowed me to run code from one block while erasing and then writing to another. I tried reconfiguring the driver MODULE in the BIB file to be SHC so that it would be decompressed and so run out of RAM. But that configuration also fails. Would I have to disable interrupts while I do the erase and write? The block that I am trying to overwrite has only configuration data in it. Any suggestions as to how to get this to work would be greatly received. Thanks in Advance Brian Price brianprice_AT_appliedcs_DOT_com_DOT_au Tag: thread creation exception Tag: 53673
  - 2
    - serial debug If I use the serial debug, where can I get debug message from? Tag: thread creation exception Tag: 53672
  - 3
    - USB memory size Hi We are using S3C2410 (ARM920T) processor with WinCE4.1 and processor is supporting USB1.1. System is able to detect the 128MB USB memory device. But could not detect 256MB. Could anyone help me. Kumar Tag: thread creation exception Tag: 53671
  - 4
    - What is the process of wake up? Hi, After the my device entered sleep state, a wake up source can wake it up. But I don't know where the resume function PmgrResume is called. Does the process of wake is begun from Reset_Handler? Thanks Fred Tag: thread creation exception Tag: 53668
  - 5
    - Exporting a custom BSP Hi, I have built a BSP for my custom platform. Now I wish to build a installer file (msi) for the same. This is what I have done. I opened the export wizard. From the catalog, I added my BSP feature. In additional directories, I added the PLATFORM\mybspdir. I build the msi file. Later I tested the msi installation I created. I removed the cec file corresponding to my bsp from the platform builder catalog, and tried installing the msi, I created. I got the following error- " A build method with the following GUID has already been imported: .. Please use a new GUID and reimport the CEC file" Next, I tried installing the msi on another system (this has none of my BSP files). The installation is aborted. No messages are shown, but it just says "CEC file could not be imported". (the version of windows CE in this systems is 4.2 where as in the previous one it is 4.1) Please advice on how to correctly export my BSP. Thank you, Best regards, Mariam. Tag: thread creation exception Tag: 53665
  - 6
    - What is the matter?RAM error or driver error? HI, When I use KITL(using VMINI) to transfer a file with size of 1M , an error happened and a error dialog popup. The comment of dialogbox is "First-chance exception in COREDLL.DLL.(0x80000002: Datatype Misalignment)". The error messages in debug window of PB is " 204299 PID:63b7e646 TID:63b7e68e Data Abort: Thread=83a2b7cc Proc=800e9348 'CEMGRC.EXE' 204300 PID:63b7e646 TID:63b7e68e AKY=00000081 PC=03fc14c4 RA=00fea681 BVA=1001a7ed FSR=00000003" When I use usb client through activesync to transfer a file with size of 1M, an error happened.The error message of pb is 173142 PID:c3a1497a TID:392dfe Prefetch Abort: Thread=83921000 Proc=800e9420 'rapisrv.exe'". Is it because of system reason or their driver 's error? my platform's addresstable is: OEMAddressTable ;;;------------------------------------------------------------- ;;; Virtual(cached) Phys Addr MB ;;;------------------------------------------------------------- ; // Cotulla-Specific Mappings (common for all boards) DCD SDRAM_BASE_C_VIRTUAL, SDRAM_BASE_PHYSICAL, 64 ; (8000 0000, A000 0000)everything SDRAM-related (eboot RAM, eboot RAMIMG, nk RAM, nk RAMIMAGE, nk MEMDEFS, ethdbg buffs) DCD ZBANK_BASE_C_VIRTUAL, ZBANK_BASE_PHYSICAL, 1 ; (8600 0000, E000 0000) Zero-Bank (in RSVD slot)- No Phy Mem needed to back up DCD MEMC_BASE_C_VIRTUAL, MEMC_BASE_PHYSICAL, 1 ; (8610 0000, 4800 0000) Memory Controller DCD PERIF_BASE_C_VIRTUAL, PERIF_BASE_PHYSICAL, 32 ; (8620 0000, 4000 0000) Mem-Mapped Registers (perifs) DCD PCMCIA_S0_IO_C_VIRTUAL, PCMCIA_S0_IO_PHYSICAL, 32 ; (8820 0000, 2000 0000) PCMCIA S0 I/O Space DCD PCMCIA_S0_ATTR_C_VIRTUAL, PCMCIA_S0_ATTR_PHYSICAL, 32 ; (8A20 0000, 2800 0000) PCMCIA S0 ATTRIBUTE MEM Space DCD PCMCIA_S0_CMN_C_VIRTUAL, PCMCIA_S0_CMN_PHYSICAL, 64 ; (8C20 0000, 2C00 0000) PCMCIA S0 COMMON MEM Space DCD PCMCIA_S1_IO_C_VIRTUAL, PCMCIA_S1_IO_PHYSICAL, 32 ; (9020 0000, 3000 0000) PCMCIA S1 I/O Space DCD PCMCIA_S1_ATTR_C_VIRTUAL, PCMCIA_S1_ATTR_PHYSICAL, 32 ; (9220 0000, 3800 0000) PCMCIA S1 ATTRIBUTE MEM Space DCD PCMCIA_S1_CMN_C_VIRTUAL, PCMCIA_S1_CMN_PHYSICAL, 64 ; (9420 0000, 3C00 0000) PCMCIA S1 COMMON MEM Space DCD LCD_BASE_C_VIRTUAL, LCD_BASE_PHYSICAL, 1 ; (9820 0000, 4400 0000) LCDC DCD BOOT_FLASH_BASE_C_VIRTUAL, BOOT_FLASH_BASE_PHYSICAL, 32 ; (9830 0000, 0000 0000) BOOT-ROM FLASH (nCS0) DCD EXPBD_CPLD_BASE_C_VIRTUAL, EXPBD_CPLD_BASE_PHYSICAL, 1 ; (9C30 0000, 0800 0000) Neponset's CPLD Registers (nCS2) DCD BCR_BASE_C_VIRTUAL, BCR_BASE_PHYSICAL, 1 ; (9C40 0000, 0A00 0000) BCR (nCS2') DCD EXPBD_SA1111_BASE_C_VIRTUAL, EXPBD_SA1111_BASE_PHYSICAL, 1 ; (9C50 0000, 1000 0000) SA1111 on Neponset (nCS4) DCD EXPBD_FLASH_BASE_C_VIRTUAL, EXPBD_FLASH_BASE_PHYSICAL, 32 ; (9C60 0000, 0400 0000) eXpansion Flash ROM (nCS1) DCD SMC_ETHERNET_IO_BASE_C_VIRTUAL, SMC_ETHERNET_IO_BASE_PHYSICAL, 1 ; (9F60 0000, 0C00 0000) Ethernet - I/O Space (nCS3) DCD SMC_ETHERNET_ATTRIB_BASE_C_VIRTUAL, SMC_ETHERNET_ATTRIB_BASE_PHYSICAL, 1 ; (9F70 0000, 0E00 0000) Ethernet - Attrib Space (nCS3) config.bib NK 98380000 01F80000 RAMIMAGE RAM 800B8000 03C00000 RAM Fred Tag: thread creation exception Tag: 53658
  - 7
    - ATADisk Problem Hi, Please see the debug output from the ATAIssueIdentify() routine of the ATAdisk driver. Do you think this is a Virtual memory mapping problem or hardware problem ? Thanks in advance. Basu. ATADISK: pATAReg = 0x1201f0 ATADISK: pATARegAlt = 0x1303f6. v_MemGran = 1 ATDISK:ATAIssueIdentify reading data 9 0 9 0 9 0 9 0 e9 7f f9 ff f9 ff 0 0 ................ 0 0 0 0 e0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 e0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 f0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 f0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 e0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 e0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 f0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 f0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 e0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 e0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 f0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 e0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 e0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 e0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 f0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 e0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 e0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 e0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 f0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 e0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 e0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 e0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 f0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 e0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 e0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 e0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 f0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 e0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 e0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 e0 ff f0 ff f0 ff f0 ff f0 ff 0 0 ................ 0 0 0 0 f0 ff f0 ff f0 ff f0 ff 0 0 0 0 ................ ATDISK: Identify Data - not MFM encoded Number of Cylinders: 9 Number of heads: 9 Unformatted bytes per track: 32745 Unformatted bytes per sector: 65529 Sectors per track: 65529 Serial number: .................... Buffer type reserved Buffer size in sectors: 65520 Number of Ecc bytes or r/w long: 65520 Firmware revision: ........ Model number: ........................................ Read/Write multiple not implemented Can not perform double word IO LBA mode NOT supported DMA NOT supported PIO cycle timing mode: ff DMA cycle timing mode: ff Current size fields MAY be valid Current number of cylinders: 65520 Current number of heads: 0 Current number of sectors/track: 0 Current sector capacity: -1048576 Sectors per interrupt with r/w multiple: 240 Multi sector setting valid Total user addressable sectors: -983056 Single word dma modes supported: f0 Single word transfer mode active: ff Multi word dma modes supported: 0 Multi word transfer mode active: 0 ATDISK:ATAIssueIdentify done ATADISK:InitDisk - Getting C:H:S from registry ATADISK:GetGeometry - RegQueryValueEx(Cylinders) returned 2 ATADISK:InitDisk - C:H:S = 9:9:65529 ATADISK:UseCHSMode - RegQueryValueEx(CHSMode) returned 2 ATADISK: DSK_Open(0x30dd0) Not loading FSD since StorageManager is active ATADISK: InitFSD succeeded ATADISK: DSK_Close ------------------------------------------------ Tag: thread creation exception Tag: 53656
  - 8
    - Invalid System Service I created a tiny kernel OS image for the CE 4.20 emulator. This all works fine in release and debug builds. Then I added TCP/IP 4 from the catalog. When I create a release build everything works fine. But when I create a debug build, and try to "Download/Intialize" from Platform builder, I get a "First chance exception in NK.EXE. (0xC000001C: Invalid System Service)" dialog. I made sure "Enable Full Kernel Mode", "Enable Images Larger than 32MB" and "Enable Kernel Debugger" are all selected. "Enable CE Target Control Support", "Enable EBoot Space in Memory" and "Enable KITL" are also selected. What am I doing wrong? Kernel debugger is waiting to connect with target. 0 PID:0 TID:0 RTC - Status Reg B - 0x02 0 PID:0 TID:0 X86Init done, OEMAddressTable = 8026a648. Welcome to the Windows CE Shell. Type ? for help. Kernel debugger failed to connect with target (KDBG open stream failed). Debugger could not initialize connection. Kernel debugger is waiting to connect with target. 0 PID:0 TID:0 CEPC Firmware Init 0 PID:0 TID:0 RTC - Status Reg B - 0x02 0 PID:0 TID:0 PCIBIOS:: BIOS Address static map to addr=a00e0000 0 PID:0 TID:0 GetPicRoutingIrqTable: Start 0 PID:0 TID:0 search_pci_bios start 0 PID:0 TID:0 search_pci_bios end fails 0 PID:0 TID:0 GetPicRoutingIrqTable: FAILS!!! 0 PID:0 TID:0 Firmware Init Done. 0 PID:0 TID:0 Looking for rom chain 0 PID:0 TID:0 Rom chain NOT found 0 PID:0 TID:0 Booting Windows CE version 4.20 for (x86) 0 PID:0 TID:0 &pTOC = 80245a78, pTOC = 804a071c, pTOC->ulRamFree = 80511000, MemForPT = 00004000 0 PID:0 TID:0 Old or invalid version stamp in kernel structures - starting clean! 0 PID:0 TID:0 Configuring: Primary pages: 15078, Secondary pages: 0, Filesystem pages = 7539 0 PID:0 TID:0 Booting kernel with clean memory configuration: 0 PID:0 TID:0 Memory Sections: 0 PID:0 TID:0 [0] : start: 80516000, extension: 00004000, length: 03ae6000 0 PID:0 TID:0 X86Init done, OEMAddressTable = 802ab7b8. 0 PID:0 TID:0 Windows CE KernelInit 4294767306 PID:3fff002 TID:3fff1da Updated eptr->e32_vsize to = 00080000 4294767316 PID:3fff002 TID:3fff1da Scheduling the first thread. 4294767316 PID:3fff002 TID:3fff1da 0x83fff030: KernelInit2: pCurThread=83fff030 hCurThread=03fff1da hCurProc=03fff002, KernelInit = 8028be3e 4294767336 PID:3fff002 TID:3fff1da 0x83fff030: Updated eptr->e32_vsize to = 00010000 4294767356 PID:3fff002 TID:3fff1da 0x83fff030: >>> Loading module NK.EXE at address 0x80240000-0x802C0000 (RW data at 0x804D3000-0x8050648B) Kernel debugger connected (KDBG stream opened). Kernel Version 1169 Checked loaded at 0x80240000, data relocated at 0x804d3000 Debugger connection established (Target CPU is X86). Loaded symbols for 'C:\WINCE420\PUBLIC\GCUSTOM\RELDIR\EMULATOR_X86DEBUG\NK.EXE' Loaded symbols for 'C:\WINCE420\PUBLIC\GCUSTOM\RELDIR\EMULATOR_X86DEBUG\KD.DLL' Finished re-loading kernel modules. Loaded symbols for 'C:\WINCE420\PUBLIC\GCUSTOM\RELDIR\EMULATOR_X86DEBUG\COREDLL.DLL' Loaded symbols for 'C:\WINCE420\PUBLIC\GCUSTOM\RELDIR\EMULATOR_X86DEBUG\FILESYS.EXE' Loaded symbols for 'C:\WINCE420\PUBLIC\GCUSTOM\RELDIR\EMULATOR_X86DEBUG\FSDMGR.DLL' Loaded symbols for 'C:\WINCE420\PUBLIC\GCUSTOM\RELDIR\EMULATOR_X86DEBUG\RELFSD.DLL' 4294767406 PID:3fff002 TID:3fff1da 0x83fff030: first = 01fb0000, last = 02000000, SharedDllBase = 03d10000 4294767436 PID:3fff002 TID:3fff1da 0x83fff030: >>> Loading module coredll.dll at address 0x03FB0000-0x03FF5000 (RW data at 0x01FFF000-0x01FFF7B0) 4294767466 PID:3fff002 TID:3fff1da 0x83fff030: Did not find emulation code for x86... using floating point hardware. 4294767556 PID:a3feff4a TID:a3feff1a 0x83fefd70: >>> Loading module filesys.exe at address 0x04010000-0x0404E000 4294767606 PID:a3feff4a TID:a3feff1a 0x83fefd70: FileSystem Starting - starting with clean file system 4294767706 PID:a3feff4a TID:a3feff1a 0x83fefd70: >>> Loading module fsdmgr.dll at address 0x03F60000-0x03F77000 (RW data at 0x01FF7000-0x01FF7760) 4294767756 PID:a3feff4a TID:a3feff1a 0x83fefd70: >>> Loading module relfsd.dll at address 0x03F90000-0x03F99000 (RW data at 0x01FFB000-0x01FFBABC) 4294767806 PID:a3feff4a TID:a3feff1a 0x83fefd70: FSREG: Logging in default user. 4294767806 PID:a3feff4a TID:a3feff1a 0x83fefd70: SetCurrentUser: Logging out (nobody), logging in default 4294767806 PID:a3feff4a TID:a3feff1a 0x83fefd70: FS: Using default path "\profiles\" 4294767816 PID:a3feff4a TID:a3feff1a 0x83fefd70: SetCurrentUser: User hives not supported -- using same registry for all users 4294767816 PID:a3feff4a TID:a3feff1a 0x83fefd70: FS: Using default path "Windows\" 4294767866 PID:a3feff4a TID:a3feff1a 0x83fefd70: FS: Using default path "Windows\" 4294767946 PID:a3feff4a TID:43fd1fd2 0x83ff2db8: Mounted ReleaseFSD volume '\Release' 4294767996 PID:a3feff4a TID:a3feff1a 0x83fefd70: Filesystem initialized! 4294767996 PID:3fff002 TID:e3ff2f92 0x83fef800: InitializeJit 4294767996 PID:3fff002 TID:e3ff2f92 0x83fef800: InitMUI: DISABLED (-2145012568) 4294768246 PID:e3fefbb2 TID:e3fcbc32 0x83ff2db8: >>> Loading module toolhelp.dll at address 0x03F80000-0x03F84000 (RW data at 0x01FF9000-0x01FF9054) Loaded symbols for 'C:\WINCE420\PUBLIC\GCUSTOM\RELDIR\EMULATOR_X86DEBUG\TOOLHELP.DLL' 4294768256 PID:e3fefbb2 TID:e3fcbc32 0x83ff2db8: >>> Loading module shell.exe at address 0x06010000-0x06023000 Loaded symbols for 'C:\WINCE420\PUBLIC\GCUSTOM\RELDIR\EMULATOR_X86DEBUG\SHELL.EXE' 4294768366 PID:83fd1fd2 TID:83fcb93a 0x83fcba88: >>> Loading module device.exe at address 0x08010000-0x0801C000 Loaded symbols for 'C:\WINCE420\PUBLIC\GCUSTOM\RELDIR\EMULATOR_X86DEBUG\DEVICE.EXE' 4294768556 PID:83fcba5a TID:83fefd32 0x83fef800: >>> Loading module ceemulsrv.exe at address 0x0A010000-0x0A014000 Loaded 'C:\WINCE420\PUBLIC\GCUSTOM\RELDIR\EMULATOR_X86DEBUG\CEEMULSRV.EXE', no matching symbolic information found. 4294768576 PID:a3feff4a TID:83fefd32 0x83fef800: ObjectCall: Failed(1): 16 4294768576 PID:a3feff4a TID:83fefd32 0x83fef800: Exception ffffffff Thread=83fef800 Proc=a3feff4a 'filesys.exe' 4294768576 PID:a3feff4a TID:83fefd32 0x83fef800: AKY=00000013 PC=8029c33a ESP=0a11d5c0 EA=00000000 Debugger disconnected successfully. Tag: thread creation exception Tag: 53654
  - 9
    - Why does SC_GetTickCount call CGSTCE instead of just returning CurMSec? Can anybody tell me why SC_GetTickCount would call CPUGetSysTimerCountElaspsed instead of simply returning CurMSec? On our XScale platform, we are experiencing a hard to repro problem where one of a handful of drivers stops responding for about 20 minutes. We've observed that at times GetTickCount momentarily jumps ahead by approximately 1165210, which is the number of milliseconds to rollover a 32 bit counter running at 3.686 MHz. The theory is that when the "victim" driver calls Sleep or WaitForSingleObject, the scheduler gets this erroneous value from GetTickCount and schedules the thread to wake up 20 minutes later than intended. So, I'm scrutinizing SC_GetTickCount. Thanks Tag: thread creation exception Tag: 53652
  - 10
    - Ne2000-compatible dri Hi, I am developing BSP for MIPS based platform. I need to enable CETK which in turn demands a fully functional Ethernet port. For this purpose I need to bring up my on-board Ethernet port which is neither PCI based nor ISA based. It is mapped through IO controller. I added Ne2000-compatible driver from drivers->Networking->LAN devices from Catalog and set the environment variable 'BSP_ICS' in my platform settings. Since the registry entries corresponding to this driver have been added in platform.reg, I expected the driver to be loaded at boot-up. But I am not able to see any debug string on console which were given in Ne2000Initialize() function of the driver nor am I able to see the corresponding dll loaded among system modules loaded. There are couple of doubts I have: 1.. Is there something else to be done which I am missing? Some registry entries or environment variables? 2.. Since this Ne2000-compatible is PCI based and my Ethernet port is not a PCI-based one, is it that it does not load the driver at all because of this reason? Tag: thread creation exception Tag: 53645
  - 11
    - Ethernet download of large nk.bin fails at same location Hi I am attempting to download a 23M RAM debug image to my PXA255 based board with 32M RAM onboard over ethernet. After about 16.1M, it fails repeatedly at same location each time. I use routines used in the XScale BSP EbootInitEtherTransport, and EbootEtherReadData, but my bootloader code is otherwise modified from XSC1BD. My download fails after 16.1M and with error message from the PB the Download failed, probably due to my device stopping to repond. I am connected with a HW debugger and when hitting break after download failed, I see that it is somewhere in the ne2000 routines, but the stack pointer and cpsr looks OK, so the system looks like it has entered an infinite loop or something. When trying to download other images, they pass if they are smaller release images, but the big debug images all fail, each at its own dedicated location. I know since I am using a "personal" bootloader, it may be a longshot, but have anybody seen similar issues? My boot.bib and config.bib MEMORY sections looks as follows when downloading nk to RAM , maybe the error lies in here. Note that the bootloader is using physical space, while the image is using virtual adressing mode. boot.bib MEMORY EBOOT 00001000 0007E000 RAMIMAGE RAM 04204000 00110000 RAM TRANSTABL 04000000 00004000 RESERVED STACK 04004000 001FC000 RESERVED IRQSTACK 04200000 00004000 RESERVED config.bib ; Name|Virtual/Cached |Size| Region Type MEMORY NK 84314000 0173C000 RAMIMAGE RAM 85A50000 005B0000 RAM EBOOT 80000000 00080000 RESERVED Regards, Inger Tag: thread creation exception Tag: 53641
  - 12
    - Secure Digital (SD) cards Hi As far as I understand wince.net 4.2 doesn't have drivers for Secure Digital (SD) cards, so we have to get a driver from the manufacturer or attempt to write our own. Good news is that Windows CE 5.0 includes an SD Memory client driver, which enables a Windows CE-based device to access an SD Memory card. Would be most grateful if someone would confirm this. Best Regards. Tag: thread creation exception Tag: 53638
  - 13
    - Regional setting with Korean fonts I posted this question yesterday and I am still struggling it. Can anyone help me please? I really need this done. I want to add Korean in the regional settings. So I went to PlatformBuilder->Project->settings->locale, add Korean, then add font GL_CE and Subset 1_30 under catalog International to my project. After I build the OS and start the device, in the Regional Setting, I still see square under Korean. I did the same thing for Chinese. Everthing is ok. I tried everthing that I can think about. Can anyone give me any information, please? Is Korean fonts supported at all? Thanks in advance Chen Tag: thread creation exception Tag: 53637
  - 14
    - USB drivers problem PB 4.2 Hello experts, here is a comparison of two cases which we currently have. Common part - targeted hardware VIA Ededn board (x86) with soldered in usb controller. Tried it with desktop OS as a test - both usb ports work. A) original (no QFEs) install of Platform Builder 4.1. Create simple platform (like enterprise web pad) x86 based BSP provided with PB and add the required parts to support usb storage device. Build and test - all works well. We use PB 4.1 normally and it behaves so on other platforms too. B) original (no QFEs) install of Platform Builder 4.2. This thing again looks difefernt so I had to learn where the old parts went. Create simple platform (like above) x86 based BSP provided with PB and add the required parts to support usb storage device. Build and test - usb doesn't work. It looks like in 4.2 usb driver isn't get loaded, though it is present in /Drivers/usb registry, but not in Drivers/Active branch. Hardware setting are common for both cases. We use loadcepc for 4.1 which came with PB 4.1 and loadcepc for 4.2 which came with 4.2. So it looks to me that something did change between 4.1 and 4.2 in usb drivers ( btw, this is an example why we don't migrate - too many efforts just to restore existing functionality)... Any ideas where to look for ? Or some kind of fix ? Anyone else did see such behaviour ? Sincerely Sergei Tag: thread creation exception Tag: 53627
  - 15
    - Task Manager wince.net 4.2 Hi We have had an app writer in who develops for pocket pc devices and was quite disappointed that our device didn't have a task manager. Is there a task manager or equivalent in windows ce .net 4.2, that allows us to see apps runing and killing hung apps like in PPC2003. Regards Tag: thread creation exception Tag: 53626
  - 16
    - Mouse problem with Headless Device Hello everybody. I've a problem with Platform Builder v4.2 I've made a project under windows C.E 4.0, that worked correctly. Now, I've upgraded to Windows C.E 4.2, and something happened... the mouse doesn't work anymore. In my project, I've writtent my own shell. In 4.0, this shell was able to receive WM_MOUSEMOVE, WM_L(R)BUTTONUP(DOWN) events. Since I'm under v4.2, this doesn't work anymore. My platform is a headless device, with every features needed (minimal GDI configuration, minimal Event notifications, etc...). In order to add the mouse, I had to manually add the SYSGEN_CURSOR variable to my platform. Then, it added the mouse in Features\Shell and user interface\User interface\Mouse. But, I already have a folder named "shell and user interface" under this root : Features\Custom device [headless device]\Shell and user interface. (here I have "Graphics windowing and events, with minimal GDI configuration, minimal GWES configuration, minimal input configuration, minimal notifications configuration, minimal window manager configuration). The main window of my shell does not receive WM_MOUSEMOVE event. I can't get cursor position with GetCursorPos(&mousePoint); . I've also noticed that in my Release Directory, I cannot found a file "kbdmouse.dll". WM_KEYDOWN and WM_KEYUP events are not received. Can anyone help me to correctly build the mouse/keyboard feature in a headless device in order to read my cursor position? Thanks in advance. Tag: thread creation exception Tag: 53625
  - 17
    - COREDLL.DLL ERROR Hi, I am working on a sandgate platform with xscale pxa255. When I use KITL(VMINI) or activesync(usb client) to transfer a big file(1M),a memory error in coredll.dll will happen. But while I use it to tansfer a small file(30k),it will work well. I want to know this is the divice driver error or system error? Any idea will be welcome. Thanks. Fred Tag: thread creation exception Tag: 53623
  - 18
    - DEBUGCHK error in smartcard when I load smartcard driver and initialize driver,the following error occurs "0x8bc15430: SCard: DEBUGCHK failed in file d:\mckendric\private\winceos\drivers\smartcrd\scard\reader.cpp at line 485 " Could anyone who hold full kernel source codes tell me the situation at line 485 in reader.c. Thx! Tag: thread creation exception Tag: 53622
  - 19
    - How to output Hive format by regcomp.exe? How to output Hive format by regcomp.exe? Hi All: I just want to upgrade RAM-based registry to Hive-based. Therefore, I follow steps as below: 1. set BSP_ENABLE_FSREGHIVE=1 2. set IMGREGHIVE=1 3. set SYSGEN_FSREGHIVE=1 in cesysten.bat 4. set SYSGEN_FSREGRAM= in cesysten.bat 5. add the key in platform.reg ; HIVE BOOT SECTION [HKEY_LOCAL_MACHINE\init\BootVars] "SYSTEMHIVE"="Documents and Settings\\system.hv" "PROFILEDIR"="Documents and Settings" "Start DevMgr"=dword:1 "DefaultUser"="User" ; END HIVE BOOT SECTION Finally, I find regcomp can't transfer reginit.ini to hive format. -----output msg-------- E:\wince\release>regcomp reginit.ini . regcomp: Got LOCALE=0409, using CodePage=1252 regcomp: Overwriting existing value [HKEY_LOCAL_MACHINE\System\StorageManager\ TFS] "Flags" in system registry regcomp: Overwriting existing value [HKEY_LOCAL_MACHINE\System\StorageManager] PNPUnloadDelay" in system registry regcomp: Overwriting existing value [HKEY_LOCAL_MACHINE\System\StorageManager] PNPUnloadDelay" in system registry regcomp: InitRegistry Finished (462 lines). regcomp: Writing registry in fdf format regcomp: Done. ---------------------- The help of regcomp.exe says "determined from flags", what flag is it? How to output Hive format? Output type will be determined from flags in the source file. FDF Output: default.fdf Hive Output: default.hv, boot.hv, user.hv Tag: thread creation exception Tag: 53618
  - 20
    - Problem with taskbar ontop setting Hi, i am working with Windows CE .Net 4.2. i want to disable OnTop property of the taskbar. i have following entries in our platform.reg [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Shell\AutoHide] "Default"=dword:0 [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Shell\OnTop] "Default"=dword:0 but after cold start, the taskbar is still on top even if registry value is 0. if i do it manually from Taskbar Settings dialog it works properly. is this a bug or is there a different way to do this? i found an old newsgroup link suggesting that it was a bug in 3.0. is it fixed in 4.2? http://groups.google.com/groups?q=ontop+taskbar+windows+ce+.net&hl=en&lr=&ie=UTF-8&selm=%23Si%24IHiZBHA.988%40tkmsftngp03&rnum=1 Thanks, Siddhesh Tag: thread creation exception Tag: 53616
  - 21
    - 18BPP Hello, We are trying to port WinCE onto an ARM board. Our LCD is capable of 18BPP whereas WinCE supports only 8,16,24 or 32BPP. How do we change the WinCE display driver to get 18BPP working? Thanks Regards Vidya Tag: thread creation exception Tag: 53614
  - 22
    - 18bpp Hello, We are trying to port WinCE onto an ARM board. Our LCD is capable of 18BPP whereas WinCE supports only 8,16,24 or 32BPP. How do we change the WinCE display driver to get 18BPP working? Thanks Regards Vidya Tag: thread creation exception Tag: 53613
  - 23
    - 18BPP color depth Hello, We are trying to port WinCE onto an ARM board. Our LCD is capable of 18BPP whereas WinCE supports only 8,16,24 or 32BPP. How do we change the WinCE display driver to get 18BPP working? Thanks Regards Vidya Tag: thread creation exception Tag: 53612
  - 24
    - How to insert/delete/modify the help link in the main help? Hi, In PCC, click [start][Help], many help links are shown. How to insert/delete/modify the help link in the main help? Thanks. Yu Tag: thread creation exception Tag: 53611
  - 25
    - how can I register a device in my driver?how can i use ActivateDev how can I register a device in my driver?how can i use ActivateDeviceE?Thank for help! Tag: thread creation exception Tag: 53610

hi all,

i have observed that whenever there is a thread creation in an application or through dll initialization [IST], an exception occurs, an soon after that it dettaches it!

DEBUG MESSAGE:
----------------------
ISThread created with handle: 0x87f99fc2

WAV: DLL_THREAD_ATTACH
Exception 002 Thread=87f83400 Proc=87f9ccb2
AKY=00000009 PC=8083b854 RA=8083b700 BVA=080a074e
Process 'device.exe'

Unhandled exception c0000005:
Terminating thread 87f83400
!!!! Work around Security violation (call forward), pth = 87f83400, proc = 'device.exe' !!!!

WAV: DLL_THREAD_DETACH

help me
regards
neo

Top