platform vs project registry settings

Tutorials Win: Microsoft Windows Forum

- Previous
  - 1
    - Problems debugging MIPSII_FP with CE 6.0 - "Step into" and remote tools are broken F11 (step into function) is broken in MIPSII_FP builds under Wince 6.0. This is reproduced on the NEC Rockhopper Vr5500 standard reference platform as well as on our own BSP. All other run-to-breakpoint operations (i.e. step out of, run to cursor, set a break point and hit 'Run') work as expected. Additionally, we have had no success getting any of the remote tools to connect to a Rockhopper BSP built with MIPSII_FP architecture. F11 and the Remote Tools work as expected with MIPSIV_FP builds (our platform and the Rockhopper). We have not investigated MIPSII (non FP) builds - that work is in progress. It would be valuable if these faults were corrected in any future SP releases. The remote tools are an essential piece of the development suite. -- -Richard Lee eMVP Tag: platform vs project registry settings Tag: 93136
  - 2
    - OHCI / USB Gurus Hi All, I am hoping someone out there can help. I have had a terrible time getting the USB host driver to run on my XSCALE (PXA270) board. I know one of the reasons is because it is running WINCE 4.1, but currently that can't be helped. As it stands, I have the OHCI sample driver that came with the OS compiling, installing, and running. I get interrupts, my IST runs, but I am not talking to any devices. What I experience is a failure on TD, with an error status of 0x5. I believe this means the device is not responding. Since NO devices respond, and I have tried multiple boards to rule out the HC, I have to assume the problem is with my driver or the hardware itself coming from the OHCI controller, to the actual USB port. Our HW guys insist the problem must be in the driver, because when they put a scope in between the USB cable, there is some sort of signal. However because the signal is differential, they can't tell me what it is, if it is TX, RX, or both. What I would like to do, is add some debug statements to my driver, to dump what goes into the transfer output buffer, and what, if anything comes back. This sounds simple enough, but I lack the USB knowledge to really know: 1) What should the output be? I believe I read somewhere when a device is first plugged in, the HCD issues a "poll" and expects "some response". But both of these are rather vague. Is there some document that describes this process in detail? I need to know what the host is expected to send, and what it is expecting to recieve. 2) I'm having a tough time figuring out where in the code I'd trace this information. My thought was I could trace the TX in IssueTransfer (cpipe.cpp), but I am not sure which of the parameters is the actual data. The reported buffer lengths are zero, so is the "poll" a "control" packet? If so, does all the data go in the lpvControlHeader? Again knowing what the data is supposed to be might clue me in. It looks like RX works the same, using the dwFlags parameter when the transfer is issued to indicate the transfer is coming from the device. So maybe I could trap both RX and TX in the same place? 3) If I am getting ANYTHING back from the device will I get an error of 0x5, or does this only occur when there is NO response? Thanks to anyone out there who has the time to answer me. My experiences implementing the USB host controller has felt like a good month of beating my head into a brick wall :) Tag: platform vs project registry settings Tag: 93135
  - 3
    - ANN: Windows CE Live Chat Tomorrow! Just a note that we'll be hosting an online chat tomorrow morning concerning Windows CE 6.0! Members of the development team will be on hand ready to answer your questions, so bring 'em on! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Title: Windows CE Live Chat! November 29, 2006 9:00 - 10:00 A.M. Pacific time Additional Time Zones: http://www.timeanddate.com/worldclock/fixedtime.html?month=11&day=29&year=2006&hour=9&min=0&sec=0&p1=234 Description: Do you have tough technical questions regarding Windows CE 6.0 for which you're seeking answers? Do you want to tap into the deep knowledge of the talented Microsoft Embedded Devices Group members? If so, please join us for a live Windows CE chat and bring on the questions! Windows CE is the operating system that is powering the next generation of 32-bit, small-footprint and mobile devices. This chat will cover the tools and technologies used to develop devices using the Windows CE operating system. To join this chat, please log on via the main MSDN chat page at: http://msdn.microsoft.com/chats/ Chat Transcripts: Missed a recent chat? We welcome you to visit the Transcript Archive. Transcripts are usually posted within two weeks of the live event. http://msdn.microsoft.com/chats/transcripts/mobileembedded/default.aspx ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Sue sloh@microsoft.com (remove "online" from reply-to address) http://blogs.msdn.com/ce_base/ _____________________________________________________________ This posting is provided "AS IS" with no warranties, and confers no rights. _____________________________________________________________ Tag: platform vs project registry settings Tag: 93124
  - 4
    - MI5 Persecution: Capital Radio - Chris Tarrant -=-=-=-=-=-=-=-=-=-=-=-=--=-=-=-=-= -= Capital Radio - Chris Tarrant -= -=-=-=-=-=-=-=-=-=-=-=-=--=-=-=-=-= Capital Radio DJs have been "in on it" from the start. One of the first things I heard in the summer of 1990 was from a Capital DJ who said, "If he listens to Capital then he can't be all bad" (supportive, you see. We're not bastards). Much of what came over the radio in 1990 is now so far away the precise details have been obliterated by time. No diary was kept of the details, and although archives if they exist may give pointers, the ambiguity of what broadcasters said would leave that open to re-interpretation. In spring 1994, Chris Tarrant on his Capital morning show made an aside to someone else in the studio, about a person he didn't identify. He said, "You know this bloke? He says we're trying to kill him. We should be done for attempted manslaughter". That mirrored something I had said a day or two before. What Tarrant said was understood by the staff member in the studio he was saying it to; they said, "Oh no, don't say that" to Tarrant. If any archives exist of the morning show (probably unlikely) then it could be found there; what he said was so out of context that he would be very hard put to find an explanation. A couple of days later, someone at the site where I was working repeated the remark although in a different way; they said there had been people in a computer room when automatic fire extinguishers went off and those people were "thinking of suing for attempted manslaughter". Finally, this isn't confined to the established radio stations. In 1990 after I had listened to a pirate radio station in South London for about half an hour, there was an audible phone call in the background, followed by total silence for a few moments, then shrieks of laughter. "So what are we supposed to say now? Deadly torture? He's going to talk to us now, isn't he?", which meant that they could hear what I would say in my room. 260 -- Posted via a free Usenet account from http://www.teranews.com Tag: platform vs project registry settings Tag: 93118
  - 5
    - CUSTOMIZABLE XP SKIN problems with my .Net CF Application Hello I come to integret the Customizable UI windows XP skin component "located in shell and user interface -> User inteface" under my Windows CE.Net 4.2 image. Whene i lunch my .Net CompactFramwork application i can't color my button whith this line code Button1.backcolor = new system.drowing.color.red !!!!!!!!! is it normal???? and what is the solution to have my button control colored like before? best regard Tag: platform vs project registry settings Tag: 93113
  - 6
    - RTC in WinCE Hi All I am trying to create Soft phone in Wince I am able to compile code of RTC API based and written in Win32 but as its come to COM componenet intialization its crashing .. in the followong code hr = ::CoCreateInstance(CLSID_RTCClient, NULL, CLSCTX_INPROC_SERVER, IID_IRTCClient/* __uuidof(IRTCClient2)*/, reinterpret_cast<void **> (&pCR->m_pClient)); reason is its returning m_pClient as NULL I readed some articles and got to know that we need to load the rtcclient.dll file. so when i trying to load WCHAR File[] = L"C:\\WINCE500\\PBWorkspaces\\PCRing\\RelDir\\Emulator_x86_Release\\rtcclient.dll"; HINSTANCE hInstLib = LoadLibraryW(File); Its returning hInstLib =NULL..! Can anyone tell me what wrong i done in load dll or wht is right way to CoCreateInstance of RTCClient in WINCE... ! Thanks in advance Neha Tag: platform vs project registry settings Tag: 93112
  - 7
    - Ohcd2 lib, usb20/ehci : Unable to sysgen with Intel compiler 2.0 Hi, I am using Intel compiler 2.0 evaluation version for PB 5.0 When I go for sysgen, I am getting error with my BSP USB host lib: "fatal error LNK1103: debugging information corrupt", I got the problem and when I am doing individual sysgen of \WINCE500\public\common\oak\drivers\usb\hcd I am not able to generate sysgen with Intel compiler So I have to compile 1) \WINCE500\public\common\oak\drivers\usb\hcd\ohcd2 2) \WINCE500\public\common\oak\drivers\usb\hcd\usb20\ehci These two lib by with default Microsoft (MS) compiler, and then I can do sysgen of whole \WINCE500\public\common\oak\drivers\usb\hcd\usb20\ehci So I want to avoid to compile these two lib by MS compiler...I want to use Intel compiler only.. Anybody can help me to solve this problem... Thanks Himanshu Gajjar Tag: platform vs project registry settings Tag: 93106
  - 8
    - About WinCE Usb ActiveSynch, What's this meaning? Dear Friend: My Usb ActiveSynch is alaways break when transfer data, and the following information was showed through DNW: Posting WM_NETCONNECT(FALSE) message, ErrorCode = 631(0x277) AUTORAS:: Dialer notifies: [2] [Dialer Terminate] What's its meaning? and How can I sove the stability of ActiveSynch, thank you very much. Best Regards Mike Han Tag: platform vs project registry settings Tag: 93095
  - 9
    - Networked Media Device in Windows CE 6.0 Hi to all I want to use Networked Media Device in Windows CE 6.0. I want to ask you that whether NMD is a part of Windows CE 6.0 or I need to install it seperately. If it is the part of same package what is the exact location of source code in wince600 folder and if it need to be installed seperately which NMD feature pack can I use. If I have to install same NMD feature pack for windows CE 5.0, will I get some feature enhancement in NMD with windows CE 6.0? Thanks in advance Tag: platform vs project registry settings Tag: 93092
  - 10
    - Break Point doesn't Work hi all, I'm debugging a stream driver in PB5.0. I set break point in ***_init and ***_open functions but it just ignored all of the break points and ran through the programs. I'm sure the driver has been loaded already since the debug message has been printed out. By the way, when I set break point for it, it is a pink circle. How to solve the problem? Thanks in advance!! Tag: platform vs project registry settings Tag: 93091
  - 11
    - What is the corresponding function calls for "GetTickCount()" Hi all, I don't know why when I try to enable multi-binFS and XIP, the return value of GetTickCount() is always a constant. Can anyone please tell what is the final OAL function that "GetTickCount()" will call finally? Thanks for the infomation. Regards, Nicholas Tag: platform vs project registry settings Tag: 93084
  - 12
    - where are wombats? Can someone tell me whether Wombats live only in Australia, or also on other continents? Apart from zoos, of course. We all know that Wombats are to be found in Zoos. 260 -- Posted via a free Usenet account from http://www.teranews.com Tag: platform vs project registry settings Tag: 93082
  - 13
    - two instance bluetooth transport I have a board that could be populated with one of two slightly different serial bluetooth modules. They have different baudrate capabilities and some other differences. I have a hardware switch that I can read to determine the populated module. I would like to build just one image to support them both. I think I can do something like: [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Bluetooth\Transports\BuiltIn\1] "Driver"="brf6300.dll" "Flags"=dword:0 "Name"="COM1:" "Baud"=dword:1c200 "ResetDelay"=dword:DAC "Priority256"=dword:78 [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Bluetooth\Transports\BuiltIn\2] "Driver"="brf6300.dll" "Flags"=dword:0 "Name"="COM1:" "Baud"=dword:2580 "ResetDelay"=dword:200 "Priority256"=dword:78 I can detect at run time which module is populated but how do I control which transport to bind too? I would think there is some kind of API call I can make?? Tag: platform vs project registry settings Tag: 93075
  - 14
    - Download to target hang at Vbridge:: NK add MAC... After adding USB host support and device driver, when I tried to download to target the system hang. Here is the bottom of the serial output file: +---------- Initialize ----------+ RCR = 0x[8] TCR = 0x[0] CR0 = 0x[D] CR1 = 0x[8] CR2 = 0x[0] CR3 = 0x[0] ISR = 0x[10000005] IMR = 0x[FF] RDSE = 0x[29710C0] TDSE[0] = 0x[29700C0] TDSE[1] = 0x[29704C0] TDSE[2] = 0x[29708C0] TDSE[3] = 0x[2970CC0] RDCSIZE = [15] TDCSIZE = [15] RDINDX = [1] TXINDX[0] = [0] TXINDX[1] = [0] TXINDX[2] = [0] TXINDX[3] = [0] RDCSR = 0x[3] TDCSR = 0x[1111] +------------------------------------------------------------+ 0x8bf67c0c: x86KitlCreateName: Using Device Name 'CEPC49284' 0x8bf67c0c: OALKitlCreateName: Using Device Name 'CEPC49284' KITL: *** Device Name CEPC49284 *** KITL: DHCP get/renew device IP: 192.168.20.43 VBridge:: built on [Oct 11 2006] time [13:08:57] VBridgeInit()...TX = [16384] bytes -- Rx = [16384] bytes Tx buffer [0xA29745A0] to [0xA29785A0]. Rx buffer [0xA29785C0] to [0xA297C5C0]. VBridge:: NK add MAC: [0-40-63-E5-C0-84] Any inputs would be great. Thanks Tag: platform vs project registry settings Tag: 93070
  - 15
    - STRATA flash and reset interopt problem I am seeing something really strange with the strata flash FMD driver. I just implemented block locking on my bootloader code and parameter blocks. Everything seems to be working except my reset command has now stoped working. The reset command does an internal watchdog reset (PXA255). I use this also to implement the KITL Target "Reset Device" command. This was working before I implemented the "locking" feature and if I "unlock" the blocks the reset majically starts working. I suspect the reset is really being issued, its just when it tries to reboot it can read the flash and locks up. If I power cycle (even with the blocks locked) it reboots fine. If I unlock, then issue the reset it also works. Can anyone explain this? Tag: platform vs project registry settings Tag: 93069
  - 16
    - UNISCRIBE performance Has anyone else experiences a significant (and visible) slow down in text drawing when adding UNISCRIBE (complex scripting) support to CE 5.0 ? I haven't gone looking to see if all text is now drawn with some other blit or line call, but we added SYSGEN_UNISCRIBE to our builds which fixed some hebrew and arabic drawing, but all text objects now render significantly slower to the point that one can see dialogs refresh. Tag: platform vs project registry settings Tag: 93066
  - 17
    - Regarding File System Filter - Calling DeviceIOControl Hello All, I need to intercept any Read/Write operations with RAM, Storage Card and HardDisk(If there is one in PocketPC, i don't really know). So I am trying to use FSDSPY Example code using Visual Studio 2005(Not Platform Builder). Registry Settings Done: =============== HKEY_LOCAL_MACHINE\System\StorageManager\FATFS\Filters\FSDSPY Name Type Value Dll String FSDSPY.dll Order DWORD 0 I have added Log messages to the file under \\Temp Directory while any directory is created in RAM, Storage Card. But Messages gets logged only when there is operation with Storage Card. This is the way I made sure FSDSPY.dll is working fine. Questions: ======= 1. Is there a way to intercept RAM read/Write file operations? 2. By doing the above registry settings, the File System Filter is applicable for all the storage. Is this understanding correct? Now i tried to write an UI Application to Call DeviceIOControl() of FSDSPY example. void GetItWorked() { HANDLE hCommDevice = INVALID_HANDLE_VALUE; HANDLE hCommEvent = INVALID_HANDLE_VALUE; DWORD dwReturn; TCHAR Buf[128]; BOOL DevIORes = FALSE; int error; hCommDevice = CreateFile(_T("DSK1:"), // drive to open GENERIC_READ | GENERIC_WRITE, // no access to the drive FILE_SHARE_READ | FILE_SHARE_WRITE, // share mode NULL, // default security attributes CREATE_ALWAYS, // disposition FILE_ATTRIBUTE_NORMAL, // file attributes NULL); // do not copy file attributes if(hCommDevice == INVALID_HANDLE_VALUE) { error = GetLastError(); wsprintf(Buf , L"Error [%d]",error); MessageBox(NULL , Buf , L"Error" , MB_OK); } else { MessageBox(NULL , L"Success in getting the DSK1 handle!!" , L"Info" , MB_OK); } hCommEvent = CreateEvent(NULL, false, false, NULL); if( hCommEvent ) { //download event object to device driver DevIORes = DeviceIoControl( hCommDevice, 0 , (LPVOID) hCommEvent, 0, NULL, 0, &dwReturn, NULL); if( DevIORes == TRUE ) { MessageBox(NULL , L"Success in Calling DevIOCtrl!!" , L"Info" , MB_OK); } } else { error = GetLastError(); wsprintf(Buf , L"Error [%d]",error); MessageBox(NULL , Buf , L"hCommEvent Error" , MB_OK); } } Questions: ======= 3. To get the Driver handle so as to call DeviceIOControl(), i used L"DSK1", was this right, since DeviceIOControl of FSDSPY is NOT called? Thanks in advance -Srini Tag: platform vs project registry settings Tag: 93065
  - 18
    - Connect to Device... Not Available Using VS 2005, CE 6.0 integrated Platform Builder. I'm trying to connect to my device via Ethernet, but the Tools menu item "Connect to Device..." is grayed out and unavailable. I have followed all of the steps in the article "How to: Connect to Windows CE Device Without ActiveSync" to no avail. Anybody have any suggestions? Tag: platform vs project registry settings Tag: 93062
  - 19
    - Closing down thread after exception Hi, i have a problem. I have 2 threads in my app, the main process app and a background worker. In the background thread i have a top level try catch block. I need to know best way to clean up handles to the background thread if it causes an exception. try{ while (g_fContinue){ WaitForSingleObject(hEvent, TIMEOUT); //some code } return 0; } catch(Exception& e){ e.ErrorMsg(); return 0; } To exit the thread from the main thread i just set the g_fContinue flag and event and then clean up but if it faults on its own where do i clean up. Can i call CloseHandle(hThread) in the catch block? Tag: platform vs project registry settings Tag: 93059
  - 20
    - GIISR, NDIS and E100BEX bad interrupt handling Hi all, E100BEX is a miniport driver given as a sample with PB 5.0. It handles Intel's 825xx Ethernet PCI chips and illustrates a few useful techniques for writing NDIS 5.1 miniport drivers. Unfortunately, there is a problem in the way E100BEX handles the interrupts. This can be seen when E100BEX is used with GIISR.DLL on a shared interrupt level. For instance, a typical Registry entry for this driver is: [HKEY_LOCAL_MACHINE\Drivers\BuiltIn\PCI\Template\E100BEX] ;PCI Bus Enumeration Information "Class"=dword:02 "SubClass"=dword:00 "ProgIF"=dword:0 "VendorID"=multi_sz:"8086","8086","8086" "DeviceID"=multi_sz:"1209","1229","2449" "Dll"="NDIS.dll" "Entry"="NdisPCIBusDeviceInit" "Transceiver"=dword:3 ;Installable ISR Handler Information "IsrDll"="giisr.dll" "IsrHandler"="ISRHandler" "PortIsIO"=dword:0 "PortOffset"=dword:0 "PortSize"=dword:4 "PortMask"=dword:F000 When the 825xx interrupt fires, it is handled by PeRPISR that calls NKCallIntChain for the active level. NKCallIntChain then calls GIISR's ISRHandle, that tests active bits of the ScbStatus register of the controller against PortMask. As the result of the test is positive, ISRHandle returns a valid SysIntr for the interrupt and the matching IST in NDIS is eventually called. The IST in NDIS calls MPIsr in E100BEX, that read 2 controller registers: ScbCommandHigh to check that the interrupt is not masked at the controller level and ScbStatus, indicating what interrupt sources (Rx, Tx, etc.) are currently active. When both the interrupts are unmasked and active sources can be seen, MPIsr writes ScbCommandHigh to mask the controller interrupts and return TRUE to NDIS. NDIS then calls InterruptDone: new interrupts can occur on the same level. When E100BEX is the only possible interrupt source on this level, after having called InterruptDone, NDIS posts a DPC that ends in E100BEX MPHandleInterrupt routine. MPHandleInterrupt reads ScbStatus again and writes it back to clear the bits of the active sources. Then it processes the controller interrupts and finally writes to ScbCommandHigh to enable the controller interrupts again. When another device shares the same interrupt level and is located in the interrupt chain *after* the ISRHandler instance of E100BEX, things usually go bad. As an illustration, imagine this scenario: 1) A 825xx interrupt is processed up to the point where NDIS calls InterruptDone, after MPIsr. The controller interrupt is disabled in ScbCommandHigh but the active interrupt sources are still set in ScbStatus. 2) Right after InterruptDone, an interrupt pending on the other device is processed. NKCallIntChain is called starting with GIISR's ISRHandle for E100BEX. Unfortunately, the ScbStatus bits are still set and the SysIntr for NDIS/E100BEX is improperly returned. 3) MPIsr is called but as the controller interrupt is masked, it returns FALSE. 4) InterruptDone is called and as the interrupt of the other device is still active, we restart to 2): the system is hanged. The problem can easily be fixed by resetting ScbStatus bits in MPIsr instead of MPHandleInterrupt. Remi Tag: platform vs project registry settings Tag: 93057
  - 21
    - AYGShell API Set not included in Windows CE 6 Core License after all ? Hi: The Microsoft Windows Embedded CE 6.0 list of operating system components states that the AYGShell API Set catalog item is included in the Core licence. Ref.: http://www.microsoft.com/windows/embedded/eval/wince/components.mspx However, the Run-time License Assessment Tool defines my OS image as requiring the Professional License when I include this item. Is the documentation wrong ? Thanks in advance ! Mark. Tag: platform vs project registry settings Tag: 93053
  - 22
    - Problem to handle VK_SELECT Hi, I am developing application on windows CE. I have a h/w which has 4 keys I have given functionality on UP(VK_UP), down(VK_DOWN), menu (OEM_SPECIFIC) and select(VK_SELECT) on these keys. Now I want to write a application to demonstrate them. For that I have written small program which has a Dialogue with 3 buttons. and I switch between them using up, down keys. But when focus is on the button I want to use VK_SELECT and select the current button and do some action. But active button does not handle this event. In fact I only get VK_SPACE event on the active button. But I want to write code on VK_SELECT event. Can anyone please tell me how to get VK_SELECT event when focus is on button and that button is your active window. Tag: platform vs project registry settings Tag: 93052
  - 23
    - LAN91C111 on PXA270 I'm porting Windows CE 5.0 MainStone BSP to a board based on PXA270. I'm trying to port the Eboot to this board. The Ethernet Controller is mapped on nCS4 (0x1000_0000). In developement kit MSC1 register value is 0aCCD1 i have not changed it in my board also. But when I try to apply it the driver in the board I am working now it appears to start ok, but it does not communicate well. The driver detects the Ethernet Controllet ok on SMCInit() routine, but It appears to fail on SCMSendFrame() or SMCGetFrame() routines. both chips have the same revision? My board doesn't have an EEPROM and I have wr0te MAC Address by hand in LAN91CInit() like // Gouri mac[0] = 0x0080; mac[1] = 0x263E; mac[2] = 0x5D0A; I am getting the following Debugg messages in the hyper terminal. Ethernet Boot Loader Configuration: 0) IP address: 0.0.0.0 1) Subnet mask: 0.0.0.0 2) Boot delay: 3 seconds 3) DHCP: (Enabled) 4) Reset to factory default configuration 5) Download new image at startup 6) Boot device order: SMSC -> PCMCIA0 -> PCMCIA1 7) Debug serial port: FFUART D) Download image now L) Launch existing flash resident image now Enter your selection: d INFO: Trying to initialize the built-in SMSC NIC... BANKSEL = 3302 MT - 0 = 3332 MT - 1 = 8000 MT - 2 = 8080 MT - 3 = 0 MGMT = d199 REV = 2dba ERDV = 4 LAN91Cxxx: Chip Id 11 Revision 10 TCR = 3332 TCR = 3332 INFO: SMSC LAN91C111 Ethernet controller initialized. INFO: MAC address: 0-E-C-80-7B-71 after that it is proceeding to next.Here it self hanging. Can anybody help me in this regard. Thanks, Gouri Tag: platform vs project registry settings Tag: 93051
  - 24
    - CE 6.0 Plat Builder builds are SLOOOW Anyone else who has used CE 5.0 platform builder noticed that a build now takes almost 3x as long for the same configuration on CE 6.0 (this is a Sysgen on either). Can't quite understand it.... Tag: platform vs project registry settings Tag: 93049
  - 25
    - Windows CE 6.0 calls to .NET CF SerialPort calls Anyone else tried or having issues with SerialPorts under .NET CF 2 (SP1) and CE 6.0? Establishing a manual connection or similar to a hyperterminal client shows comms is ok from the OS side of things, but if I write a .NET CF application (that runs fine under CE 5), opening a SerialPort object causes the program to throw an IOException. I have resorted to using the CE 5.0 com16550.dll in my build image - then it works fine. Tag: platform vs project registry settings Tag: 93047
- Next
  - 1
    - Bootloader - unresolved external Hi Guys I have been making a bootloader (for AT91SAM9261), I have made needed functions (main, startup) and I have a problem with final linking and making eboot.exe file. In the output of build -c there is an error "BUILD: [01:0000000080:ERRORE] Startup.obj : error LNK2001: unresolved external s ymbol StartUp". It does not matter if in my StartUp.s file there is or there is not this label (and "EXTERN Startup"). I can't find out, why it happens. So, could anybody help? Here is a content of my sources file: TARGETNAME=EBOOT TARGETTYPE=PROGRAM RELEASETYPE=PLATFORM _COMMONPUBROOT=$(_PUBLICROOT)\common __PROJROOT = $(_WINCEROOT)\public\AT91SAM9261_MICROTECH_BIN EXEENTRY=StartUp SOURCES=StartUp.s \ main.c \ flash.c \ cdc_enumerate.c \ init_SAM9.c \ xmodem.c TARGETLIBS=$(_COMMONOAKROOT)\lib\$(_CPUDEPPATH)\blcommon.lib \ $(_COMMONOAKROOT)\lib\$(_CPUDEPPATH)\fulllibc.lib WINCETARGETFILES=BootImage StartUp code is without any errors. Tag: platform vs project registry settings Tag: 93037
  - 2
    - ethernet download of image Hi, I'm trying to download my CE image to my target (Kontron ETX-PM board). I selected ethernet as download and transport protocol in the target device connectivity options in platform builder. On the target, I boot from a bootable USB stick with a WIN98 boot disk on it. I fire up loadcepc with following arguments : loadcepc -v eboot.bin output on the display of the target is : ------------------------------------------------------------------------------------------- Warning A20 line already enabled 4 PCI busses (Version 2.10) using configuration mechanism # 1 JUMPtec Version. No HIMEM.SYS required. WARNING : Current drive has not been prepared with JSYSCE! Windows CE may nog run correctly! Total free extended memory = 64448, largest block = 64448 Block allocated at 0x110000 Loading eboot.bin, size = 77667 Image physical start = 0x00130000, size = 84728 Section physical start = 0x00130000, size = 16 Section physical start = 0x00130040, size = 8 Section physical start = 0x00131000, size = 70652 --------------------------------------------------------------------------------------------- then the display goes blank and shows a : Jumping to 0x00138888 At that point, I instruct platform builder to attach to the target. Meanwhile on the debug port : ------------------------------------------------------------------------------------------- Microsoft Windows CE Ethernet Bootloader Common Library Version 1.0 Built May 24 2002 21:38:01 Copyright (c) 2000-2001 Microsoft Corporation Microsoft Windows CE Ethernet Bootloader 3.3 for CE/PC (Aug 23 2006) Boot Args @ 0x28136 PCI Device Configurations (4 PCI bus(es) present)... ======================================================== Bus, Device, Function = 0, 2, 0 Vendor ID, Device ID = 0x8086, 0x3582 Base Class, Subclass = 3, 0 => DISPLAY_CTLR Interrupt = 9 BaseAddress[0] = 0xE8000000 (Memory) BaseAddress[1] = 0xE0000000 (Memory) BaseAddress[2] = 0x1800 (I/O) ======================================================== Bus, Device, Function = 0, 2, 1 Vendor ID, Device ID = 0x8086, 0x3582 Base Class, Subclass = 3, 128 => DISPLAY_CTLR Interrupt = 0 BaseAddress[0] = 0xF0000000 (Memory) BaseAddress[1] = 0xE0080000 (Memory) ======================================================== Bus, Device, Function = 0, 29, 0 Vendor ID, Device ID = 0x8086, 0x24C2 Base Class, Subclass = 12, 3 => SERIAL_BUS_CTLR Interrupt = 9 BaseAddress[4] = 0x1C00 (I/O) ======================================================== Bus, Device, Function = 0, 29, 1 Vendor ID, Device ID = 0x8086, 0x24C4 Base Class, Subclass = 12, 3 => SERIAL_BUS_CTLR Interrupt = 11 BaseAddress[4] = 0x2000 (I/O) ======================================================== Bus, Device, Function = 2, 8, 0 Vendor ID, Device ID = 0x8086, 0x103A Base Class, Subclass = 2, 0 => NETWORK_CTLR Interrupt = 7 BaseAddress[0] = 0xE0201000 (Memory) BaseAddress[1] = 0x4000 (I/O) ======================================================== FindAllPCINetCard: Searching for PCI Ethernet NIC ... FindALLPCINetCard(0): Found Ethernet NIC (IRQ=7, IOBase=0x4000, Type=55). FindPCINetCard:Argument IOBASE=0, IRQ=0,TYPE=0 FindPCINetCard:Found 1 PCI Ethernet NIC ... FindPCINetCard: Found Ethernet NIC (IRQ=7, IOBase=0x4000). Turning on Busmaster, IO, and MEM 17 Check Busmaster, IO, and MEM 17 I8255xInitDMABuffer: DMA address: 0x200000 - size = 0x20000 I8255xInit: Init using i/o address : 0x4000 - stride = 0x1 I8255xInit: dev i/o address : 0x4000 EEPROM I/O Base: 4000 00000000:000000E0:0000004B:0000000C:00000091:00000003, I/O at 4000, IRQ 0. Receiver lock-up workaround activated. I8255x: open() irq 0. I8255x: Done open(), status 2090. I8255xInit: SUCCESS! Returned MAC Address:00:E0:4B:0C:91:03 System ready! Preparing for download... Using device name: CEPC37123 Hit ENTER within 3 seconds to enter static IP address!InitDHCP():: Calling ProcessDHCP() ProcessDHCP()::DHCP_INIT Got Response from DHCP server, IP address: 150.158.192.62 ProcessDHCP()::DHCP IP Address Resolved as 150.158.192.62, netmask: 255.255.248.0 Lease time: 259200 seconds Got Response from DHCP server, IP address: 150.158.192.62 No ARP response in 2 seconds, assuming ownership of 150.158.192.62 +EbootSendBootmeAndWaitForTftp Sent BOOTME to 255.255.255.255 Sent BOOTME to 255.255.255.255 Sent BOOTME to 255.255.255.255 Sent BOOTME to 255.255.255.255 Sent BOOTME to 255.255.255.255 Sent BOOTME to 255.255.255.255 Locked Down Link 1 Src IP 150.158.192.62 Port 0800 Dest IP 150.158.198.129 Port 11AF EthDown::TFTPD_OPEN::boot.bin -EbootSendBootmeAndWaitForTftp TFTP link[0]: State:0, DestAddr.wPort: 0, SrcAddr.wPort: 0 TFTP link[1]: State:3, DestAddr.wPort: 4527, SrcAddr.wPort: 2048 TftpReceiver, port: 0x0000D403, wkp: 0x0000D403 ------------------------------------------------------------------------------------------- At this point, the target reboots and show me my win98 dos prompt again. Platform builder still shows the message 'Waiting for BOOTME from CE device' Any hints are welcome... Tag: platform vs project registry settings Tag: 93031
  - 3
    - Problem accessing a buffer pointer hello all We have a custom built monolithic USB Host controller driver on WINCE 5.0. When we connect a storage class device the mass-storage class driver gets loaded and runs it's initializations. In this process when the partition driver is loaded we happen to get a buffer pointer for a read request on bulk. When we write to this buffer in the HCD we get a data abort exception. We found that 1. the pointer is not NULL 2. MapCallerPtr is called before we get it in the HCD. Is there any pre-processing that we need to do before we access any such pointer. I have already tried LockPages. please advise. Shreepad Tag: platform vs project registry settings Tag: 93029
  - 4
    - Problem accessing a buffer in USB stack hello all We have a custom built monolithic USB Host controller driver on WINCE 5.0. When we connect a storage class device the mass-storage class driver gets loaded and runs it's initializations. In this process when the partition driver is loaded we happen to get a buffer pointer for a read request on bulk. When we write to this buffer in the HCD we get a data abort exception. We found that 1. the pointer is not NULL 2. MapCallerPtr is called before we get it in the HCD. Is there any pre-processing that we need to do before we access any such pointer. I have already tried LockPages. please advise. Shreepad Tag: platform vs project registry settings Tag: 93027
  - 5
    - Serial port modem connection I have a GPRS modem that I want to use for internet connectivity on my CE device. My CE Platform has 3 serial ports - and I have first-third instance of serial port configured in PB. Hardware-wise, the platform's BIOS assigns 3F8 to COM1, 2F8 to COM2 and 2E8 to COM3. CE grabs 3F8 for serial debug and 2F8 becomes the new COM1. I notice CE sets 2E8 to be the new COM3. If I create a direct connection, only COM1 and COM3 are available but if I get the available COM ports programmatically, I get COM1 and COM2. My problem is I cannot get serial comms working with the modem, but it works fine if I set up a direct serial connection between the CE device and a host PC (visible in hyperterminal as the CE device polling "CLIENT CLIENT..."). Creating a modem connection via the CE default "Hayes" modem on COM1 works without any issue but does not work with my modem entry below on COM3 (I get a "Port is not available: another program may be using it" message). I create the additional modem connection in the registry as follows: [HKEY_LOCAL_MACHINE\ExtModems\WaveComm] "Port"="COM3" "DeviceType"=dword:1 "FriendlyName"="WaveComm Modem on COM3" I have tried changing COM3 to COM2 without success. There seems to be something I am missing settings wise or in the registry but after all my help trawling and registry analysis I cannot figure out what (the fact that I can't see the CE registry remotely doesn't help either - see my other post) Any ideas? Tag: platform vs project registry settings Tag: 93023
  - 6
    - Windows CE 6.0 remote tools broken? I'm having lots of problems trying to connect to a CE 6.0 device using the remote tools like registry viewer. The device is connected via Ethernet and debugging via Visual Studio 2005 works fine. I haven't been able to resolve it, after doing/checking the following: - made sure KITL enabled build setting is on and all the KITL settings in the connectivity options are checked. -Tried debug and release builds - I am trying to use KITL Tranpsort as transport and CESH as startup server - I get the error "Unable to load device side components. Please check server configuration settings". These settings worked fine under CE 5.0 platform builder (and still does). - tried running both the CE 5.0 and CE 6.0 versions of the remote tools directly by launching the .exe's without success. - I have tried all other remote connection methods/combos (KITL/CESH/MANUAL) without success. What should I check I should have component-wise in my build to get this working - as far as I can tell, my build has the same components as my CE 5.0 version. Tag: platform vs project registry settings Tag: 93022
  - 7
    - About mediaplayer in CE5.0 Hello guys! When I used mediaplayer to play mp3,I want to use the button to control volume: For example:When I press one button,the volume turn down.And when I press another button ,it turn up. I also want to know:whether I can use a button to open the mediaplayer directly.I didn't find any materials to tell me how to do it ,please give some advices! Thanks in advance. Tag: platform vs project registry settings Tag: 93021
  - 8
    - start os on power on Hi All, Does anyone know how I can store my OS, generated using PB CE 6.0 on my development board and have my OS start up on power on? Thanks, RH Tag: platform vs project registry settings Tag: 93020
  - 9
    - clear Default Credentials Hi, How can I clear the Default Credentials set by the Net logon dialog? I wish to create some sort of log-off button that will enforce re-entering of the User/Pass info. Ohad Tag: platform vs project registry settings Tag: 93016
  - 10
    - Help, why my usb host support usb mouse, but the mouse cursor doesn't be showed? Dear friends: I have a question, I select Usb Host related part, and I can use usb mouse, but I can't see the cursor on wince screen, I think I have must lost some necessary catalog, please help to know what catalog I must add to solve my problem. Best Regards Mike Han Tag: platform vs project registry settings Tag: 93014
  - 11
    - Interpreting ERROR!!! Calling xxx_SetProcPermissions in Wince 6.0 with platman 'cepermon' tool I'm working on an SoC architecture where various drivers and user application code need to share access to the specialized hardware coherently. For example, the state video subsystem must be identically viewed by all clients - display drivers, dshow filters, etc. To implement this, I wrapped the hardware libraries in a device driver, using IOCTLs to marshall bits in from user mode. Works like a champ. However, now when I run the Remote Performance Monitor tool, I get a fairly rich spew of messages out the debug port when using the driver. 137392 PID:4cc0002 TID:5310002 ERROR!!! Calling xxx_SetProcPermissions 137696 PID:4cc0002 TID:5310002 ERROR!!! Calling xxx_SetProcPermissions 138404 PID:4cc0002 TID:5310002 ERROR!!! Calling xxx_SetProcPermissions 138707 PID:4cc0002 TID:5310002 ERROR!!! Calling xxx_SetProcPermissions 139414 PID:4cc0002 TID:5310002 ERROR!!! Calling xxx_SetProcPermissions 139780 PID:4cc0002 TID:5310002 ERROR!!! Calling xxx_SetProcPermissions 140424 PID:4cc0002 TID:5310002 ERROR!!! Calling xxx_SetProcPermissions 140828 PID:4cc0002 TID:5310002 ERROR!!! Calling xxx_SetProcPermissions 141435 PID:4cc0002 TID:5310002 ERROR!!! Calling xxx_SetProcPermissions or roughly every 300 msec while viewing any one of a number of parameters including CE processor Statistics/% processor time This is on a build where only the display driver is accessing the hardware device driver. Altering the build so that the display drier is linked to a KM DLL exporting the APIs directly, the messages go away. Anyone have a clue what the origin/interpretation of this message is? --Richard R. Lee eMVP Tag: platform vs project registry settings Tag: 93013
  - 12
    - Difference between Nk.nb0 & nk.bin Hi all I am new to the platform builder. When i do Sysgen it will create both Nk.nb0 and Nk.bin. I am always using Nk.nb0 as OS image file. My question is : What is the difference between Nk.nb0 and Nk.bin. Thank you V. Vijaya Mohan Software Engineer Carmanpark.co.ltd Tag: platform vs project registry settings Tag: 93004
  - 13
    - Developing NDIS drive for Windows Mobile 5.0 Hi, I want to develop a intermediate NDIS driver for a WM 5.0 IntelPXA270 based phone . Actually it is a variation of the passthru driver (a miniport driver at one end and a protocol driver at the other end). Based on what I can understand so far, I need to use platform builder for Windows CE 5 to develop the driver for the targeted platform after creating a OS design using the Intel PXA27X BSP and then export that as a CAB file which can be installed on a WM 5.0 device. Is my understanding correct? Thanks in advance. ravi Tag: platform vs project registry settings Tag: 93003
  - 14
    - Platform Builder 5.0 and Windows Vista Hi, This week I tried Vista. It seams that I can't make Platform Builder 5.0 works under Windows Vista. The program starts but when I try to build it hangs (not responding). Anyone was able to make it work on Vista? Tag: platform vs project registry settings Tag: 92996
  - 15
    - design templates in WinCE 6.00 Hi all, Anybody knows how can I make a template similar that custom device template that appears when you create a new Platform Builder project ?? The templates in XML seem that have been removed. Any ideas? Thanks Tag: platform vs project registry settings Tag: 92990
  - 16
    - FormatMessage() failed + LocalFree() problem Hi all, when i launch this piece of code (WinCE6 version) : if ( DeviceIoControl (hServices,ui32Function,pvParamIn,ui32InBufferSize, pvParamOut,ui32OutBufferSize,&ui32BytesReturned, NULL) == FALSE) { LPVOID lpMsgBuf; FormatMessage(FORMAT_MESSAGE_ALLOCATE_BUFFER | FORMAT_MESSAGE_FROM_SYSTEM | FORMAT_MESSAGE_IGNORE_INSERTS, NULL, GetLastError(), 0, // Default language (LPTSTR) &lpMsgBuf, 0, NULL); LocalFree (lpMsgBuf); ui32RetVal = 0xFFFF; } then, i have got an error at the line LocalFree(), and a break point at : Coredll: DEBUGCHK failed in file C:\ymzki\private\winceos\COREOS\core\lmem\.\rheap.cpp at line 1344 Olivier Tag: platform vs project registry settings Tag: 92986
  - 17
    - How to add splash screen Hi, I want to add splash screen in my( x86 based) winCE 5.0 device . My requirement is just to add still image in splash screen while booting . please tell me the procedure to add the splash screen . Thanks in Advance. Amit Tag: platform vs project registry settings Tag: 92985
  - 18
    - Modifying Code in BaseClasses of Directx Hi All, I am using Win CE 5.0. I have modified code in "WinCE\500PUBLIC\DIRECTX\SDK\SAMPLES\DSHOW\BASECLASSES". I had done Build and Sysgen for that project alone. It is generating a strmbase.lib file. Later I am building Run-time Image and download the code to the Target Device, I cannot see any effect of changed code. But in PB help it is written that the Code can be modified. Can anyone help me regarding this issue. Is there any other specific way that needs to be done to see the effect of changed code. Thanks in Advance, Sarath Chandra. B Tag: platform vs project registry settings Tag: 92982
  - 19
    - Multiple display modes in WinCE Hi, I have added support for two display modes in display driver (VGAFlat) for emulator in WinCE5.0. My intention was to change the display mode from smaller resolution to higer resolution dynamically (with out restart). I have tried with ChangeDisplaySettingsEx but it returned 0 (fail). Can any one throw some light on this? Is there any way I can change the Display mode in the Emulator dynamically. Thanks in advance. SriV Tag: platform vs project registry settings Tag: 92981
  - 20
    - Autobuilds in WinCE 6.00 Hi All, Anybody has any experience in how to do automatic builds using WinCE 6.0? What scripts or configuration files are you using to do that? Thanks! Tag: platform vs project registry settings Tag: 92977
  - 21
    - C.I.D. Is it possible to change the C.I.D. (that is the the Card IDentification of an SD card) wrote by the manufacturer? Mhaxx Tag: platform vs project registry settings Tag: 92974
  - 22
    - Is there any develpment kit for mainstone III Hi all, Is there any develpment kit for mainstone III? i have upgraded mainstone II BSP to mainstone III.Till now i was using intel pxa270 processor development kit. Whether i can use the same develpment kit? rgds princy Tag: platform vs project registry settings Tag: 92970
  - 23
    - Bluetooth - virtual Serial Port Hello, since a few days I'm struggling with the following problem: I'm using the PB 5.0 (XScale platform) sample "comtest" to create virtual Bluetooth COM ports and connect to another BT enabled PC. As long as I'm using client connections (Outgoing), everything works fine. However when I'm using the CE device as server (Incoming), the other PC cannot establish a connection (can't even see it). From the local CE view, everything looks working pretty well, i.e. the virtual COM port is registered successfully, the COM-port can be openend successfully but I'm waiting endless for an incoming connection. Furthermore, I can't see the "Serial" profile on the other PC, only a "Personal Ad-hoc Service" and a "Audio" profile. Establishing a connecting to these other profiles is no problem. Is there a need or way to make this serial profile visible first? Is there a PC-tool which can be used to establish a serial connection direct to a specific BT-ID? Maybe everything works o.k. but it is not visible due to some reason? Thank you very much, Robert Tag: platform vs project registry settings Tag: 92968
  - 24
    - lvds Hi all My target work fine with a VGA output , but instead i want to use the LVDS. But nothing on screen when CE boots. Bios and dos is ok (i mean the screen displays the prompt) any idea. regards Tag: platform vs project registry settings Tag: 92967
  - 25
    - mis match time stamp problem while building Hi, I tried to make the run time image(project is builded some time back) and I got the error makeimg: run command: romimage E:\WINCE500\PBWorkspaces\intel\RelDir\Emulator_x86_Debug\ce.bib Error: Mismatched time stamp on .rel file for module celog.dll requesting kernel fixup. Valid .rel file is required for kernel fixups. Windows CE ROM Image Builder v4.0.120 Copyright (c) Microsoft Corporation I searched in the gruops and got one solution as rebuild the platform with sysgen and enable the option clean before build. I did but got strange errors in header files ppkfuncs.h Those are not errors and the code is perfect. I tried in another way: removed the all projcets from work space and sysgen with clean before building option enabled. Still got errors is some other header file OAL-intr.h My platform is itself not working. I did many projects in that one. How can I solve this problem? my mail id is embeddedkumar@gmail.com . Rgds, kumar. Tag: platform vs project registry settings Tag: 92959

what is the order of parsing platform.reg and project.reg

Am I correct in assuming if I have the same registry setting specified in
both, the platform setting takes precedence?

Top

Re: platform vs project registry settings by Bruce

Bruce
Tue Nov 28 14:54:21 CST 2006

That is correct, look at the output of makeimg, you will find fmerge calls
for the reg files. The order is specified there. You can also look at
reginit.ini, which has all of the registry settings in the order that they
will be applied.

--
Bruce Eitman (eMVP)
Senior Engineer
beitman AT applieddata DOT net

Applied Data Systems
www.applieddata.net
An ISO 9001:2000 Registered Company
Microsoft WEP Gold-level Member

"skindiver" <xd@ttt.com> wrote in message
news:%23RKEYCyEHHA.3608@TK2MSFTNGP02.phx.gbl...
> what is the order of parsing platform.reg and project.reg
>
> Am I correct in assuming if I have the same registry setting specified in
> both, the platform setting takes precedence?
>
>
>

Top