nb0 creationing

Tutorials Win: Microsoft Windows Forum

- Previous
  - 1
    - CEUpdateCheck I was fooling around and launched this tool from VS2K5. My system has CE 3.0, 4.1, 5.0, and 6.0 installed. It showed that some of the QFEs were/are broken or not installed. I have "fixed" some of the QFE installations by reinstalling the updates in an attempt to make the tool happy. CE 3.0 and 4.1 are now good-to-go, but for some reason the tool keeps telling me my 5.0 QFE updates are broken, no matter what updates I reinstall. FWIW, all of the QFE updates were installed previously, so I am not sure what caused the tool to think they were broken and/or not installed. Can this tool be trusted, or should I just install the updates and ignore what it is telling me? Thanks. Tag: nb0 creationing Tag: 113988
  - 2
    - Active Sunc large amount Data Transfer Hi, I am using wince 5.0 with PXA270. The target device and host PC (Windows XP) are connected with Active Sync 4.5 over USB. I tried copy file of 30MB size from Host PC to target device. Active Sync connection is breaking after it transfers 15MB data. I tried number of times but results are same. I updated all 2007 QFEs, is that got messed up ? Is avtive sync is not capable of transfering large amount of data ? Please any hints or suggestions or anyone tried before this. Thanks Tag: nb0 creationing Tag: 113985
  - 3
    - NAND flash 256MB (K9F5608UOD) driver? Hi, Professional Buddies, Platform CE 6.0 I use IXP 435 CPU, and it connects a 256MB NAND flash at expansion bus (CS3). Is there a nand flash driver inside the PB 6.0? I don't know how to do it. Could you give me a advise please ? Tag: nb0 creationing Tag: 113982
  - 4
    - regd. Windows Mobile SDK Hi, I understand SDKs are specific and generated based to any hardware platform and we have the Windows Mobile Professional 6.0 and Standard 6.0 SDKs for Pocket PC Phones and smartphones I would like to understand on what hardware platforms are these SDKs are generated. Is it based on a generic design template such as Handheld devies??? Suppose I have a handset hardware platform, is it guarnteed that application created out of Microsoft Mobile SDKs going on work on them as it is.. Is there any specific standardistion to bench mark any hardware platform for mobile devies as PocketPC or Smartphones, etc. Thanks, Tag: nb0 creationing Tag: 113980
  - 5
    - SDRAM Modification can any one give me the list of files to be modified if i replace the SDRAM with higher capacity. Tag: nb0 creationing Tag: 113978
  - 6
    - Causes for unusual RAS State Transition Platform: Windows CE 5.0, ARMV4I I have a wireless interface stack that works well on other platforms but on this one particular platform we are seeing RAS drop the connection as soon as RAS reports state RASCS_Authenticated. We typically see a RAS state transition to RASCS_Connected from RASCS_Authenticated, instead we get RASCS_Disconnected. I have the serial driver instrumented so know that there is not a COM event being reported with EV_RLSD, EV_RING, EV_ERR, or EV_POWER. I have not been able to get the SAMPLE TSPI to work, nor get a replacement UNIMODEM to install. I have been able to replace ASYNCMAC with my own so know for certain that the line is being torn down due to some code forcing a state transition to LINECALLSTATE_IDLE. Since the device is a commercial device I cannot change or instrument the OS, nor is there any debug serial output. Any thoughts as to reasons that RAS would behave like this? Tag: nb0 creationing Tag: 113975
  - 7
    - VirtuaAllocCopyEx not mapping as UnCached Hi, I am running windows ce 6.0 on an ARM11 target with an armv4 compiler. I have the following scenario. I have a structure named queue and I am allocating it on kernel side and trying to map it to user side using VirtualAllocCopyEx. On a nutshell this is what I am doing inside Map(). queueAddrUM = VirtualAllocCopyEx(GetCurrentProcess(),(HANDLE)ui32ProcessID,queueAddrKM,ui32Size, PAGE_READWRITE | PAGE_NOCACHE); Which means that in queueAddrUM I have the base address for the allocated queue whose kernel address is queueAddrKM). Now I try to update a member of the queue by doing: queueAddrUM->info = some->info and at random times queueAddrUM->info does not get updated instead it keeps the previous values, i.e the value of queueAddrKM->info. It's as though the assignment statement did not exist or it wasn't really mapped(Note: sometimes it works). Any ideas what might be wrong here? P.S queueAddrUM is of type queue and VirtualAllocCopyEx is being called from kernel mode. Please do not be confused by the simplicity of my example, I just tried to keep the problem simple, the types are correct and function calls seem to be placed in context. Thank you very much for the help. Tag: nb0 creationing Tag: 113953
  - 8
    - asynchronous access Like ceallocasynchronousbuffer api description, this api must be used by synchronous access. what does it mean by synchronous access or asynchronous acess? Tag: nb0 creationing Tag: 113952
  - 9
    - GPE 1bpp probelm? hi all, am using GPE in WINCE42.NET with the SMDK2410 BSP which have the LCD controll onchip. The driver can work well under 8bpp, 16bpp, but now when porting for the 1bpp monochrome. The display driver have problem? 1. On the desktop the icon cannt display, but the wince logo BMP display normal. 2. There is no hardware curor, and the cusor donot display. when change the Blt virtual function to the emulagte implement, there is still the problem. SCODE S3C2410DISP::BltPrepare(GPEBltParms *blitParameters) { blitParameters->pBlt = EmulatedBlt; return S_OK; } SCODE S3C2410DISP::BltComplete(GPEBltParms *blitParameters) { return S_OK; } SCODE S3C2440DISP::SetPalette(const PALETTEENTRY *source, USHORT firstEntry, USHORT numEntries) { return S_OK; } who can give some advise on the 1bpp with no hardware Blt and cursor accelator GPE derived driver. Tag: nb0 creationing Tag: 113950
  - 10
    - user mode driver restriction from ce 6.0. Some kernel APIs are not available from user mode driver of ce 6.0. What APIs are restricted for um driver? And some of kernel APIs are available by support of reflector. But it is also restricted by registry setting of the driver from fully accessing kernel api. what's the registry settings? I'm surveying the user mode driver's restriction on ce 6. Plz explain it as detail as possible. Tag: nb0 creationing Tag: 113949
  - 11
    - Excessive Frame Drops in pimg application during video capture on I am working on ARMV4I device with WM6 OS using pimg application. My stream interface camera driver followes 3 pin architecture and use "client limited" model drived from MSFT provided NULLCAM driver. For around 4 mins of wmv video capture i am getting around 30KB video seems to have only 9-10 frames. I am passing RGB data on both Preview and capture pin. Capture resolution is QCIF(176x144). Is there any way, by which i can tell Video Capture filter to not drop even a single frames anyhow ? Because of frames drops of video capture filter, we are getting very bad quality and performance. Is there any way we can overcome this problem? Thanks ab Tag: nb0 creationing Tag: 113947
  - 12
    - MFC application development and debugging Hi, I want to use MFC as the development method of my application. After a research, I learned that I have to make a new SDK project and use this new SDK as the target platform of an MFC project in VS2005. Everything is fine until here. Now, I want to debug the OS and the application at the same time, as I used to do with Windows CE 4.2. Also, I want to use KITL over ethernet connection to do the debugging. I use 2 instances of VS. I download the OS image with one of the VS instances, the system boots and I see the desktop. Then what should I do to download the application on this system and debug through the ethernet connection? Is there a method to build and include the application code in the image as a subproject and debug like an api application? I couldn't find a step-by-step explanation and I really do not want to use ActiveSync connection. Thanks in advance, selin_at_heitec Tag: nb0 creationing Tag: 113941
  - 13
    - Can we config WinCE more than one device ? Hi We can set WinCE to a USB serial or RNDIS or mass storage device , can we set it more than one device ? Thank for your teaching . Tag: nb0 creationing Tag: 113940
  - 14
    - Getting an image into flash without PB(5) Hi, is there a way to get nk.bin/nb0 into flash without PB? e.g. - 1) stand alone tool with ethernet connection or so? - 2) prepare it to some kind of file that can be flashed with a standard flashtool -- Maarten Tag: nb0 creationing Tag: 113939
  - 15
    - USB function client driver question Hi I've known that we can change usb function client class type as serial or mass storage or RNDIS . [HKEY_LOCAL_MACHINE\Drivers\USB\FunctionDrivers] "DefaultClientDriver"="Serial_Class" or "DefaultClientDriver"="RNDIS" or "DefaultClientDriver"="Mass_Storage_Class" [HKEY_LOCAL_MACHINE\Drivers\USB\FunctionDrivers\Mass_Storage_Class] "Dll"="usbmsfn.dll" I have some question that if we do not add "Dll" key and bundle the driver, can this function driver work ? If there is no usb function client driver running, can Microsoft Activesync work ? Thank for your teaching. Tag: nb0 creationing Tag: 113937
  - 16
    - Internet explorer problem (how to release memory) Dear All, When I use Internet explorer in windows CE5.0 , it seems work ,but I found system getting slow when I open several website pages , finillay , IE almost take all memory in system , and make me surprise memory will not release even I close IE as well, does my system have some problem ? how to solve it ? thank you very much! I am sure I had search this question for a while in this group but can not get result I want , so I post here hope you can help ! thank you very much ! Best Regards, Calvin Liu Tag: nb0 creationing Tag: 113936
  - 17
    - =?KOI8-R?Q?=2D=8D_=8D_=8D_KERELA_couples_Enjoying_SEX_at_NET_CAFE?= Hi....Friends, watch and enjoy SECRET WEB-CAMS at LADIES HOSTELS and INTERNET CAFE SEX SCANDALS VIDEOS... http://www.hollywoodpopstars.blogspot.com http://www.googlemobilesphones.blogspot.com Tag: nb0 creationing Tag: 113935
  - 18
    - ======> Secret Video CLIPS <========= Hi....Friends, watch and enjoy SECRET WEB-CAMS at LADIES HOSTELS and INTERNET CAFE SEX SCANDALS VIDEOS... http://www.hollywoodpopstars.blogspot.com http://www.googlemobilesphones.blogspot.com Tag: nb0 creationing Tag: 113934
  - 19
    - Windows CE Config.bib Hi Folks, I am here to clarify a few questions that I have regarding config.bib and OEMAddressTable in Windows CE. I have been working on application software for a few years but only recently transitioned to do some work on the BSP layer. The following are my questions. I kindly apologize if you think the question is too trivial or basic for this newsgroup, 1. From the documentation on MSDN I can gather that Windows CE has a OEMAddressTable which specifies virtual to physical address mapping. Virtual memory mapping range is from 0x80000000 to 0x9FFFFFFF. A second virtual address range from 0xA0000000 to 0xBFFFFFFF is automatically mapped for each entry in the OEMAddressTable. My question here is in Windows CE we have a 4 Gb virtual address space with kernel VA space on the top 2 Gb and application space in the bottom 2 Gb. In this table we only specify a physical address mapping for the cached and non-cached parts of the VA for the kernel? How does this mapping map back for PA space for the application's VA? 2. The Config.bib file specifies a mapping between memory region and type (RAMIMAGE, RAM etc). My first question here is is this VA or PA that is specified here? Second, there is also an option to specify NANDIMAGE? So is NANDIMAGE for allowing XIP execution form Nand Flash? Also if some one can give some explanation as to how the OEMAddressTable ties to Config.bib will be very helpful. - Kuete Yves Tag: nb0 creationing Tag: 113933
  - 20
    - Double databank entries in "Categories Database" and "DB_notify_events" If I use the ROM-only file system after every restart i get double entries in the databanks "Categories Database" and "DB_notify_events" (and only in these!). If I use the RAM and ROM file system I get these double entries only after a reboot via SetSystemPowerState. I have the system already stepped through with the debugger from SetSystemPowerState to KernelIoControl(IOCTL_HAL_REBOOT...), however, i could find no database access. The double db entries are presumably generated during the system start. But where? How can I find the bug? Some more infos: OS: Windows CE 6.0 R2 with all updates CEPC: eBox-4300 MSJK SPARK BSP: ICOP_eBox4300_60DS Hive-based Registry Internal Solid State Disk mounted as root directory Before using a new run time image i cleared the disk with DELTREE. A file system replication filter was not integrated yet (I don't know how). SYSGEN_AS_BASE=1 SYSGEN_AS_FILE=1 SYSGEN_AS_MAIL=1 SYSGEN_AS_PIM=1 SYSGEN_ATADISK=1 SYSGEN_ATAPI=1 SYSGEN_FATFS=1 SYSGEN_FSDBASE=1 SYSGEN_FSREGHIVE=1 SYSGEN_FSROMONLY=1 or SYSGEN_FSRAMROM=1 (see above) PRJ_ENABLE_FSREGHIVE=1 PRJ_ENABLE_FSMOUNTASROOT=1 PRJ_BOOTDEVICE_ATAPI=1 Tag: nb0 creationing Tag: 113932
  - 21
    - Touch Screen Problem I am working on SMDK2410. I am having problem in touch driver. problem 1: on my device DOTNETCF managed application is running.if i press button on the software and move the finger in LCD, button leave event is still not raised. problem 2: in my software i have three button in the same line, if i pressed first and last button same time then it will raise the event of second button.can we set that if two button are pressed same time then windows will reject the command. can any one help me in these matter. Tag: nb0 creationing Tag: 113929
  - 22
    - WINCE5 Ram image runs fine, Flash image crashes Hi, I have an image that runs perfectly well in RAM (loaded by PB5). If I turn on IMGFLASH to make it a flash image and load it into flash, the same image crashes just after OEMInit, saying repeatedly: Data Abort: Thread=8bfd70cc Proc=882264b0 'filesys.exe' AKY=00000003 PC=80076184(NK.EXE+0x00036184) RA=00000001(???+0x00000001) BVA=ffff ffff FSR=00000007 anyone having sugestions to debug this? -- Maarten Tag: nb0 creationing Tag: 113922
  - 23
    - Ethernet debugging Hi, I am working with WINCE 5.0 on Freescale's imx31 board. I have got problem with ethernet. * With KITL/Ethernet , both debugging and normal TCP/IP works fine * Without KITL the Ethernet driver Ping itself fails. i tried with ipconfig on target which returned "No IPv4 adapter found" I think ethernet is not configured properly, can any one please help how to resolve this problem. Regards Santhosh Tag: nb0 creationing Tag: 113915
  - 24
    - Dr Watson influence on real-time behavior We have several applications running under Windows CE 5.0 on a PXA270 processor. From time to time one of our drivers is generating interrupts every 2.5 milliseconds which are handled by an IST with priority 20 (highest of all our applications/drivers). The IST reads data from a FIFO buffer filled by the driver. Normally the IST is scheduled within 50 microseconds but occasionally it takes about 15 ms before it's scheduled to handle the interrupt. This results in data loss when reading the FIFO buffer. The problem occurs occasionally by running the same stress test script when the application is started. By adding CeLog data messages in our application and analyzing the CeLog files with Kernel Tracker, we discovered that the latency occurs right after one of the threads in our application throws a c++ exception. The intended exception is caught and handled by our application correctly. We have Dr Watson enabled in our OS design and decided to remove it to see if it has any influence. Intensive testing after removing Dr Watson proved us that the problem no longer occurs. We suspect that Dr Watson is watching the thread that throws the exception and logs it; if Dr Watson's buffer is full it is flushed to the dump file. Sometimes this happens during the period where our driver is generating interrupts that need to be handled within a short time and influences the real-time behavior. This is just a suspicion since we cannot track the Dr Watson activities. Can someone confirm that adding Dr Watson to the design indeed influences the real-time behavior? Are there ways to overcome this and still have Dr Watson in the design? Thanks In Advance, Bonne Zwaga Tag: nb0 creationing Tag: 113914
  - 25
    - Confused between SROM and SDRAM In oemaddrtab_cfg.inc file DCD 0x8A000000, 0x28000000, 32 ; 32 MB SROM(SRAM/ROM) BANK 5 DCD 0x8C000000, 0x30000000, 24 ; 32 MB DRAM BANK 6 this SROM is part of physical SDRAM mounted on board or it will part of S3C2410 processor only. Tag: nb0 creationing Tag: 113912
- Next
  - 1
    - SDK compilation problem for winnetwk.h Hi, I want to use MFC to develop my application, therefore I followed the guidelines in MS virtual labs class for Writing MFC/Native applications. I prepared my own SK based on the BSP I use, installed it and started the simple smart device MFC project. However, the MFC application gives the following error when I try to compile it: 1>D:\Program Files\Windows CE Tools\wce600\Heitec_MFC_SDK\include\ARMV4I\shlobj.h(120) : fatal error C1083: Cannot open include file: 'winnetwk.h': No such file or directory When I build the SDK again, I receive the following error and winnetwk is not among the added files: Warning: You have one or more CPU families to be included in the SDK that have missing or out-of-date headers and libraries. Make sure to build the following configurations: iMX31_Phytec_Binary ARMV4I Debug I cloned the sample project of the BSP provider to develop this SDK and the OS design is successfully built without the SDK. How can I resolve this problem? I don't know what this missing file does, or why the system needs it. And I don't want to add more catalog features to my platform. BR, Selin_at_heitec Tag: nb0 creationing Tag: 113911
  - 2
    - OPENING FOR WINDOWS DEVICE DRIVER IN CHENNAI Hi, Greetings from Scillatec. Scillatec Solutions Pvt Ltd is a HR Consultancy Company based at Chennai. Scillatec is a leading management, systems and technology consulting firm. With Chennai as its base we target Clients both at National Level and International Level; we have a team of skilled people, whose skills extend from the initial generation of ideas, insights, solutions and new technology, all the way through to detailed implementation. We recruit across various industry segments both IT and Non IT. Our Client is looking for =93Windows device drivers=94 programming Professionals for their office in Chennai. Skill sets: Windows device drivers Positions: SE/SSE/TL Experience: 3 to 7 yrs Job Location: Chennai Interested Candidates can send your updated Resume to pradeepa@scillatec.com mentioning the below: =95 Your Current CTC =95 Your Expected CTC =95 Notice Period Thanks & Regards, Pradeepa.M HR Executive Scillatec Solutions Pvt Ltd Ph: 044- 42121608 www.scillatec.com Tag: nb0 creationing Tag: 113910
  - 3
    - How to define USB device interfaces and endpoints Hi Do you know how to define USB device interfaces and endpoints in Windows CE , I would like to let PC catch more than one USB device , can we do that ? How can I read data from USB Host or send data to it ? Is there any api or driver IO control for use ? Thank for your teaching. Tag: nb0 creationing Tag: 113908
  - 4
    - Question regarding Windows CE USB interfaces Hi Please excuse my ignorance , i am extremely new to wince driver development. Actually i have a windows CE 5.0 device which presently behaves as a display device when connected on usb.It has a single interface for vendor class. now i want to add 1 audio control and streaming audio interfaces to it so that the windows host pc may recognise this as an audio device also. I wanted to know if it is possible to have multiple interfaces in wince because i read in msdn (http://msdn.microsoft.com/en-us/library/ms894093.aspx) that "The USB function controller drivers support single configurations and single interfaces". Moreover audio streaming requires an alternate interface of zero bandwidth , does windows CE support alternate interfaces. Thanks in advance!! Paramita Tag: nb0 creationing Tag: 113907
  - 5
    - Windows CE USB Hi Please excuse my ignorance , i am extremely new to wince driver development. Actually i have a windows CE 5.0 device which presently behaves as a display device when connected on usb.It has a single interface for vendor class. now i want to add 1 audio control and streaming audio interfaces to it so that the windows host pc may recognise this as an audio device also. I wanted to know if it is possible to have multiple interfaces in wince because i read in msdn (http://msdn.microsoft.com/en-us/library/ms894093.aspx) that "The USB function controller drivers support single configurations and single interfaces". Moreover audio streaming requires an alternate interface of zero bandwidth , does windows CE support alternate interfaces. Thanks in advance!! Paramita Tag: nb0 creationing Tag: 113906
  - 6
    - Booting WinCE 6.0 on ARM9 based target board Hi, I am having trouble trying to boot our ARM 9 based target boards on CE 6.0. I have been able to successfully boot the board under CE 5.0, but after porting the BSP to 6.0, I can not get anything up. I get " NK Kernel: DEBUGCHK failed in file C:\ymzki\private\winceos \COREOS\nk\kernel\nknormal\..\schedule.c at line 376". followed by DEBUG_BREAK @8838835c Ignored. on pressing the 'F5' (run) key, the same messages follow. Does anybody have any ideas where to go from here? Some logs follow. Thanks In Advance, VIJAY R PB Debugger The Kernel Debugger is waiting to connect with target. 4294767296 PID:0 TID:0 Setting up softlog at 0x89ffc000 for 0x800 entries 4294767296 PID:0 TID:0 Booting Windows CE version 6.00 for (ARM) 4294767296 PID:0 TID:0 &pTOC = 8976ac1c, pTOC = 8971d48c, pTOC- >ulRamFree = 8976f000, MemForPT = 00001000 4294767296 PID:0 TID:0 Old or invalid version stamp in kernel structures - starting clean! 4294767296 PID:0 TID:0 Configuring: Primary pages: 2185, Secondary pages: 0, Filesystem pages = 1092 4294767296 PID:0 TID:0 Booting kernel with clean memory configuration: 4294767296 PID:0 TID:0 Memory Sections: 4294767296 PID:0 TID:0 [0] : start: 89771000, extension: 00002000, length: 00889000 4294767296 PID:0 TID:0 NKStartup done, starting up kernel. 4294767297 PID:0 TID:0 Windows CE KernelInit 4294767302 PID:400002 TID:2 Reserve VM for kernel XIP DLls, first = c0010000, last = c0db0000 4294767305 PID:400002 TID:2 g_pprcNK == 0x89768aa0 4294767305 PID:400002 TID:410002 Updated eptr->e32_vsize to = 00012000 4294767306 PID:400002 TID:410002 Initializing Memory Mapped File Support 4294767306 PID:400002 TID:410002 Scheduling the first thread. 4294767306 PID:400002 TID:410002 Detecting VFP... 4294767307 PID:400002 TID:410002 VFP Not Found! 4294767307 PID:400002 TID:410002 LoaderInit: Initialing loader 4294767309 PID:400002 TID:410002 Updated eptr->e32_vsize to = 00012000 4294767310 PID:400002 TID:410002 Updated eptr->e32_vsize to = 000a2000 4294767311 PID:400002 TID:410002 Updated eptr->e32_vsize to = 0001a000 4294767397 PID:400002 TID:410002 Heap Statistics at 0xC019FAC0 4294767403 PID:400002 TID:410002 PGPOOL: Reserved 768 pages for Loader pool 4294767404 PID:400002 TID:410002 PGPOOL: Reserved 256 pages for File pool 4294767414 PID:400002 TID:410002 Exception 'Data Abort' (4): Thread- Id=00410002(pth=89ffb024), Proc-Id=00400002(pprc=89768aa0) 'NK.EXE', VM-active=00400002(pprc=89768aa0) 'NK.EXE' 4294767414 PID:400002 TID:410002 PC=883b1d7c(kernel.dll+0x00083d7c) RA=883b1cf4(kernel.dll+0x00083cf4) SP=d001f74c, BVA=00000041 4294767415 PID:400002 TID:410002 CHECKTAKECRITSEC: Violation of critical section ordering, holding CS 8976a5c0 (1) while taking CS 8976a620 (10) 4294767415 PID:400002 TID:410002 NK Kernel: DEBUGCHK failed in file C: \ymzki\private\winceos\COREOS\nk\kernel\nknormal\..\schedule.c at line 376 4294767416 PID:400002 TID:410002 DEBUG_BREAK @8838835c Ignored. 4294767417 PID:400002 TID:410002 RtlDispatchException: returning failure. Flags=0 4294767417 PID:400002 TID:410002 NK Kernel: DEBUGCHK failed in file C: \ymzki\private\winceos\COREOS\nk\kernel\nknormal\..\exdsptch.c at line 333 4294767417 PID:400002 TID:410002 DEBUG_BREAK @883491fc Ignored. 4294767418 PID:400002 TID:410002 Unhandled exception c0000005: 4294767419 PID:400002 TID:410002 Terminating thread 89ffb024 4294767419 PID:400002 TID:410002 Secondary thread in proc 00400002 faulted, Exception code = c0000005, Exception Address = 883b1d7c! 4294767419 PID:400002 TID:410002 Terminating Thread 00410002 4294767420 PID:400002 TID:410002 CHECKTAKECRITSEC: Violation of critical section ordering, holding CS 8976a5c0 (1) while taking CS 89768b94 (13) 4294767420 PID:400002 TID:410002 NK Kernel: DEBUGCHK failed in file C: \ymzki\private\winceos\COREOS\nk\kernel\nknormal\..\schedule.c at line 376 4294767420 PID:400002 TID:410002 DEBUG_BREAK @8838835c Ignored. Tag: nb0 creationing Tag: 113905
  - 7
    - IRQ_OSMR0 PXA270, mainstoneII All, I see this statement and it is stating (first one isn't really needed). // Setup static interrupt mappings (first one isn't really needed) OALIntrStaticTranslate(SYSINTR_RESCHED, IRQ_OSMR0); OALIntrStaticTranslate(SYSINTR_RTC_ALARM, IRQ_RTCALARM); 1. I'm not taking my system to idle or powerdown mode. Why do we need IRQ_OSMR0? Can I disable that interrupt ? Thanks, Rishi Tag: nb0 creationing Tag: 113904
  - 8
    - 80070490 in korean windows mobile OS hello. all~ I found 'support code 80070490 ' on activesync. I got the korean windows mobile OS handset. And using mail and contact information to activesync with PC. Once I change locale setting from Korean to English, activesync has ERROR 80070490. I found several model of Korean windows mobile OS. Is it windows mobile bug? Tag: nb0 creationing Tag: 113902
  - 9
    - Question about unused address space PXA270, Mainstone II It is a mistake in our code. We dont have FPGA at all and this statement has been residing in the code for long. DCD 0x90B00000, 0x08000000, 1 ; MAINSTONEII: nCS2 (lower half): Board registers (FPGA). Also, in our interrupt init functions we have statments like, BOOL BSPIntrInit() { g_pBLRegs = (volatile MAINSTONEII_BLR_REGS *) OALPAtoVA(MAINSTONEII_BASE_REG_PA_FPGA, FALSE); // Mask and clear all FPGA interrupts. // g_pBLRegs->int_msk_en = 0; g_pBLRegs->int_set_clr = 0; } Also accesses to MAINSTONEII_BASE_REG_PA_FPGA are happening in InitDebugSerial(), OEMWriteDebugLED(). I'm not sure what damage this could cause ? Will this cause sudden system hang as we are facing one such issue and literally clueless ? any help guys. -Rishi Tag: nb0 creationing Tag: 113900
  - 10
    - Questions regarding x86 Hi there. I am leading an effort to develop a kind of navigational application. I started about a week ago with no knowlege what so ever about WinCE development. The device we are using is a small touch screen x86 PC. (iEi Afolux AFL-07a ) I have managed to use platform builder to create the WinCE platform and it works great. My second step is to create an environment for the developers to do their thing in. That is, generate the SDK with the emulator. Unfortunately I have found out that x86 does not support emulation. Now my question is... what is the best way to proceed? Should I ditch x86 and build another WinCE platform on the ARMv4 and develop my applications(.NET CF) for that? The other thing I noticed is that if I start a new Windows Ce 5.0 Device application I can actually run the application in Windows XP. I can even use the debugger found in Microsoft .NET Framework SDK v2.0 to debug the application. What I would like to have is that when I press F5 in VS2005 it just runs the executable instead of trying to fire up an emulator. Is this at all possible? I tried setting the debug action to "Start external program" with the debug executable as the program but it does not work. It wants to launch an emulator. Any help or advice would be greatly apreciated. I just want to know what is the best coarse of action for me to take right now. Kind regards, Werner Tag: nb0 creationing Tag: 113889
  - 11
    - Navready 2009 + Activesync over RNDIS Hi all, I want to know if Activesync connectivity is possible over RNDIS on WindowsCE 5.0, with PND profile in WindowsCE 5.0? If so any registry settings need to be changed? Thanks in Advance! Tag: nb0 creationing Tag: 113888
  - 12
    - Booting from USB Win CE 6.0 on ICOP VSX-6154 Was this post ever resolved? http://www.microsoft.com/communities/newsgroups/en-us/default.aspx?&query=VSX-6154&lang=en&cr=US&guid=&sloc=en-us&dg=microsoft.public.windowsce.platbuilder&p=1&tid=d599b9ac-bc95-44bb-aff0-50a51bf07423&mid=d599b9ac-bc95-44bb-aff0-50a51bf07423 I am having the same issue. I am able to get the demo CE 6.0 image to run on the board but have not been able to get any of our own images to load and run on the board. We just get a blank screen. Tag: nb0 creationing Tag: 113880
  - 13
    - Problem Adding .net compact framework 2 and 3.5 to wince 4.20 Help please!! I am trying to add .net compact framework 2.0 and also 3.5 to wince420 platform. The QFEs are up to date as of feb08. None of the files for 2.0 or 3.5 appear in the build, only those for compact framework 1.0. If I take out compact framework 1.0 they still dont appear and I have no compact framework at all. ceconfig.h only has the define for V1 and this I presume is why the 2.0 and 3.5 files are not being included. Clean builds don't help. In desperattion I have just tried a clean build of a new platform, without the compact framework box ticked and then added 2.0 and 3.5 to platfrom. No compact framework. As far as I can tell - whatever is supposed to tell sysgen to put the appropriate hash defines in ceconfig.h is NOT doing it and I can't tell why. HELP! (For info - in the build window - SYSGEN_DOTNETV2 etc etc are defined as set=1. so why does ceconfig.h not have the appropriate defines?) Thanks Coppo Tag: nb0 creationing Tag: 113871
  - 14
    - difference between the internal filesystems hi? PB provides two types of internal filesystem, ram only and 'ram & rom filesystem'. From pb document, I read article about them. But I couldn't understand the difference between them practically. Practically, what is the difference using them? Tag: nb0 creationing Tag: 113870
  - 15
    - Why GetSystemPowerStatusEx always return false I wrote my own backlight driver, the driver will call GetSystemPowerStatusEx to determine the power source is AC or Battery. I have added SYSGEN_PM and SYSGEN_BATTERY in my image (i.e. the catalog->Core OS->Core OS sevice->Battery Driver/Power Management(Full) are selected, I have not written my own battery driver). But GetSystemPowerStatusEx or GetSystemPowerStatusEx2 always return false in my backlight driver. Do I must write my own battery driver to provide BatteryDrvrGetStatus() to make GetSystemPowerStatusEx return TRUE, or just the MS public battery driver I included is enough? If it is because I did not written my own driver, why the POWER applet in Control Panel can show "Charging, Backup Batteries"? I think the POWER applet in control also use GetSystemPowerStatusEx to get power status. Thanks for any help. Tag: nb0 creationing Tag: 113866
  - 16
    - Nk.bin and Kiosk display problem Visual Studio 2005 and PB R2 using Platform: VIA MARK CEPC:X86 Display Driver: VIA Prosavage Display Driver I will predicate equiment Vega86 Embedded. I can to constitute but when I put the Compact Flash it doesN't LCD screen the vision. Ä°t was to be light then to go out. If I put on the normal monitor I can take CE's screen but the writes are not see. What can I do this problem? Thank you... Tag: nb0 creationing Tag: 113864
  - 17
    - LOOP in migrating Wce500 BSP to Wce600 Hi: we are migrating our bsp from Wce500 to Wce600. when build pass comipler and link(no error message), build enter into a forever loop and outpout the following message: ===> BUILD: [00:0000004309:PROGC ] Building LINK Pass in C:\WINCE600\PLATFORM\wce600_nxc2600\SRC\BOOTLOADER\ directory. BUILD: [01:0000004322:PROGC ] Linking C:\WINCE600\platform\wce600_nxc2600\target\MIPSII\retail\BOOT.exe BUILD: [01:0000004340:WARNN ] fulllibc.lib(atox.obj) : warning LNK4099: PDB 'ccrtconv.pdb' was not found with 'C:\WINCE600\public\common\oak\lib\MIPSII\retail\fulllibc.lib' or at 'C:\WINCE600\platform\wce600_nxc2600\target\MIPSII\retail\ccrtconv.pdb'; linking object as if no debug info BUILD: [01:0000004341:WARNN ] fulllibc.lib(xtoa.obj) : warning LNK4099: PDB 'ccrtconv.pdb' was not found with 'C:\WINCE600\public\common\oak\lib\MIPSII\retail\fulllibc.lib' or at 'C:\WINCE600\platform\wce600_nxc2600\target\MIPSII\retail\ccrtconv.pdb'; linking object as if no debug info BUILD: [01:0000004342:WARNN ] fulllibc.lib(delete.obj) : warning LNK4099: PDB 'ccrtheap.pdb' was not found with 'C:\WINCE600\public\common\oak\lib\MIPSII\retail\fulllibc.lib' or at 'C:\WINCE600\platform\wce600_nxc2600\target\MIPSII\retail\ccrtheap.pdb'; linking object as if no debug info BUILD: [01:0000004343:WARNN ] fulllibc.lib(handler.obj) : warning LNK4099: PDB 'ccrtheap.pdb' was not found with 'C:\WINCE600\public\common\oak\lib\MIPSII\retail\fulllibc.lib' or at 'C:\WINCE600\platform\wce600_nxc2600\target\MIPSII\retail\ccrtheap.pdb'; linking object as if no debug info BUILD: [01:0000004344:WARNN ] fulllibc.lib(malloc.obj) : warning LNK4099: PDB 'ccrtheap.pdb' was not found with 'C:\WINCE600\public\common\oak\lib\MIPSII\retail\fulllibc.lib' or at 'C:\WINCE600\platform\wce600_nxc2600\target\MIPSII\retail\ccrtheap.pdb'; linking object as if no debug info BUILD: [01:0000004345:WARNN ] fulllibc.lib(new_mode.obj) : warning LNK4099: PDB 'ccrtheap.pdb' was not found with 'C:\WINCE600\public\common\oak\lib\MIPSII\retail\fulllibc.lib' or at 'C:\WINCE600\platform\wce600_nxc2600\target\MIPSII\retail\ccrtheap.pdb'; linking object as if no debug info BUILD: [01:0000004346:WARNN ] fulllibc.lib(new.obj) : warning LNK4099: PDB 'ccrtheap.pdb' was not found with 'C:\WINCE600\public\common\oak\lib\MIPSII\retail\fulllibc.lib' or at 'C:\WINCE600\platform\wce600_nxc2600\target\MIPSII\retail\ccrtheap.pdb'; linking object as if no debug info BUILD: [01:0000004347:WARNN ] fulllibc.lib(lldiv.obj) : warning LNK4099: PDB 'ccrthelp.pdb' was not found with 'C:\WINCE600\public\common\oak\lib\MIPSII\retail\fulllibc.lib' or at 'C:\WINCE600\platform\wce600_nxc2600\target\MIPSII\retail\ccrthelp.pdb'; linking object as if no debug info BUILD: [01:0000004348:WARNN ] fulllibc.lib(diverr.obj) : warning LNK4099: PDB 'ccrthelp.pdb' was not found with 'C:\WINCE600\public\common\oak\lib\MIPSII\retail\fulllibc.lib' or at 'C:\WINCE600\platform\wce600_nxc2600\target\MIPSII\retail\ccrthelp.pdb'; linking object as if no debug info BUILD: [01:0000004349:WARNN ] fulllibc.lib(encptr.obj) : warning LNK4099: PDB 'ccrtmisc.pdb' was not found with 'C:\WINCE600\public\common\oak\lib\MIPSII\retail\fulllibc.lib' or at 'C:\WINCE600\platform\wce600_nxc2600\target\MIPSII\retail\ccrtmisc.pdb'; linking object as if no debug info BUILD: [01:0000004350:WARNN ] fulllibc.lib(invarg.obj) : warning LNK4099: PDB 'ccrtmisc.pdb' was not found with 'C:\WINCE600\public\common\oak\lib\MIPSII\retail\fulllibc.lib' or at 'C:\WINCE600\platform\wce600_nxc2600\target\MIPSII\retail\ccrtmisc.pdb'; linking object as if no debug info BUILD: [01:0000004351:WARNN ] fulllibc.lib(purevirt.obj) : warning LNK4099: PDB 'ccrtmisc.pdb' was not found with 'C:\WINCE600\public\common\oak\lib\MIPSII\retail\fulllibc.lib' or at 'C:\WINCE600\platform\wce600_nxc2600\target\MIPSII\retail\ccrtmisc.pdb'; linking object as if no debug info BUILD: [01:0000004352:WARNN ] fulllibc.lib(strncpy.obj) : warning LNK4099: PDB 'ccrtstrg.pdb' was not found with 'C:\WINCE600\public\common\oak\lib\MIPSII\retail\fulllibc.lib' or at 'C:\WINCE600\platform\wce600_nxc2600\target\MIPSII\retail\ccrtstrg.pdb'; linking object as if no debug info ===> why??????? i install PB5 and PB6 together on myPC if this caused the above loop ??? hope to get your response. Thanks & BR vincent Tag: nb0 creationing Tag: 113863
  - 18
    - USB RNDIS KITL failed for interrupt mode Hi, Now I am developing the USB RNDIS KITL and the polling mode for KITL can work properly. But when I turn to KITL interrupt mode, the NK booting process will hang while loading the relfsd.dll. And aslo KITL repeatedly prints out the debug message: KITLSend(0): Timed out waiting for ack (AckExpected: 50, TxSeq: 66) Can anyone tell me what is the root reason for this problem? Thank you! B.R Tengyeyan Tag: nb0 creationing Tag: 113861
  - 19
    - flash mdd and pdd model in R2 Hi All, My query is releated to Windows CE 6 R2. In FAL-FMD model, I created 3 partitions (PART_BOOTSECTION, PART_BINFS and PART_DOS32 in the bootloader itself) in NAND flash using BOOTPART.lib which created MBR in a format recognized by MSPART which when the device boots up, recognizes the partition table and loads appropriate file system drivers. In R2's mdd-pdd model flash driver architecture, MSPART.dll is replaced by FLASHPART.dll which makes use of a different MBR format, different from the format understandable by MSPART. I noticed that FLASHPART was not able to detect the partition table (MBR) created by BOOTPART as it is not recognized by FLASHPART anymore (Ref.: "Flash mdd and pdd driver architecture" from windows CE documentation). Following are the relevant questions: 1) Is there a module like BOOTPART that create partitions (at the bootloader level itself) and MBR which will be recognized by FLASHPART? 2) Is there any significant advantage (or added features) in moving to mdd-pdd model whilst FAL-FMD model itself works without any issues in R2? 3) Where can i get the source code for flashmdd.dll and flashpart.dll? (there is no option to install shared source code from R2 release DVD) Thanks in Advance. Regards, Devanathan.B Tag: nb0 creationing Tag: 113860
  - 20
    - HOT NEWS FROM MICROSOFT....... YES ITS REALLY HEART BREAKING NEWS FOR EVERYONE http://polticsinfs.blogspot.com/ Tag: nb0 creationing Tag: 113851
  - 21
    - WNetEnumResource API failed with error of 6118 HI, 1) Can we configure the Windows CE device for DOMAIN? 2) As device(connected to router) is not on any domain (ipconfig /all showing Domain Name: ... blank) , can we pass some domain name in lpRemoteName parameter for network resorce function WNetEnumResource . 3) If then pass the domain name like above it gives 6118 eror of servers not found 4) As we have network provider-> Domains-> servers (PC) -> in networks .. what it will be in case of Windows CE. 5) Target is to enumerate the network resource using WinCE Tag: nb0 creationing Tag: 113849
  - 22
    - about cirrus maverickcrunch coprocessor Hi, All Cirrus only provides float function like sin(...) which use its maverickcrunch coprocessor. But the coprocessor doesn't work on normal float multiply. Does BP50 compiler support the coprocessor. Please let me know if anyone have any idea how to do it, thanks Cheng Shi Emtronix Tag: nb0 creationing Tag: 113846
  - 23
    - Want to increase RAM to 512MB We have a custom board...on that board currently we two 128MB of RAM now we want to increase it to 512MB each. so i want to know where i have to change in the code. Tag: nb0 creationing Tag: 113841
  - 24
    - PXA270 SSP DMA problem Hi, I am setting up intel pxa270 ssp port to transmit data and receive data in DMA mode. I am using 8 byte per burst, and the TFT=4, RFT=8, idth of on-chip peripheral=8, i found the first burst does not generate DMA request, which causing loss of 8 byte data on every transfer. Do any one face this problem as well? How to overcome? Thanks, James -- Message posted via PocketPCJunkies.com http://www.pocketpcjunkies.com/Uwe/Forums.aspx/wince-pb/200807/1 Tag: nb0 creationing Tag: 113840
  - 25
    - USB example with isochronous transfers Hi, I was wondering if anybody knew of any example USB device and/or host drivers in CE 5.0 or 6 that use isochronous transfers. I would like to transfer some audio from a CE5.0 device to a CE5.0 host. The other transfer types are all exemplified well with the included public code and I have these working fine for video/control data. However, I'm having difficulties in finding examples of isochronous transfers or any documentation on the subject of their implementation. Any recommended books, websites, or example code on the subject would be helpful. Thanks, Jon Tag: nb0 creationing Tag: 113832

As I known, any config.bib settings like following would produce nb0 file.
ROMOFFSET=FFFFF000
ROMSTART = 00000000
ROMWIDTH = 32
ROMSIZE = 00001000
but there was no produced nb0 but bin file only exist.
Is there any other more setting?

Top

Re: nb0 creationing by Bruce

Bruce
Tue Jul 08 07:09:48 PDT 2008

Did you copy the config.bib to your _FLATRELEASEDIR?

Your ROMSIZE is very small, but that won't keep it from creating many nk.nb*
files.

--
Bruce Eitman (eMVP)
Senior Engineer
Bruce.Eitman AT EuroTech DOT com
My BLOG http://geekswithblogs.net/bruceeitman

EuroTech Inc.
www.EuroTech.com

"daniel" <daniel@discussions.microsoft.com> wrote in message
news:31B87F5E-D9C4-4027-9034-801F2C90E174@microsoft.com...
> As I known, any config.bib settings like following would produce nb0 file.
> ROMOFFSET=FFFFF000
> ROMSTART = 00000000
> ROMWIDTH = 32
> ROMSIZE = 00001000
> but there was no produced nb0 but bin file only exist.
> Is there any other more setting?

Top

Re: nb0 creationing by Silver

Silver
Tue Jul 08 10:36:12 PDT 2008

do the settings happen to be wrapped in IF IMGFLASH or similar?

Top

Re: nb0 creationing by Bruce

Bruce
Tue Jul 08 10:50:15 PDT 2008

Good question Geoff.

The OP should check the ce.bib file to see if the changes are in it.

--
Bruce Eitman (eMVP)
Senior Engineer
Bruce.Eitman AT EuroTech DOT com
My BLOG http://geekswithblogs.net/bruceeitman

EuroTech Inc.
www.EuroTech.com

"Silver" <moc.liamtoh@gnirrevliseht> wrote in message
news:eUJfqES4IHA.1420@TK2MSFTNGP06.phx.gbl...
> do the settings happen to be wrapped in IF IMGFLASH or similar?

Top