Can I use PB to build the btscosnd driver and download it onto my SPV C600

Tutorials Win: Microsoft Windows Forum

- Previous
  - 1
    - KITL not Working Hai Greats, HW : AMD DBAu1200 (MIPS Platform) SW : Windows CE 5.0. Problem: Windows CE Image built with KITL support and Target Control (shell.exe). Image is downloaded to the target through Platform builder with Ethernet transport enabled in the connectivity options. After download, while booting, the device is not getting connected with the Platform builder that is KITL Operating in Active mode. And the PB is waiting to connect with KITL Transport, but it is not occuring. So, what could be the problem. Yours, Arun. Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88994
  - 2
    - SCardGetStatusChange Problem Hi everyone, I am having problem with function I cannot get to work properly when no card are inserted into my reader. The first call with SCARD_STATE_UNAWARE return immediately with dwEventState equal to 0x000222. Then I copy this value into CurrentState recall SCardGetStatusChange. Return without blocking again but this time with dwEventState equal to 0x000012. If I repeat the process without inserting a card it will switch of status between 0x000222 and 0x000012 back and forth. If I insert a card in the reader it will return me that a card is present and the next call to SCardGetStatusChange will block until I remove the card which is correct... Do you have any idea what it could be? Regards, Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88992
  - 3
    - How to use one Analog-to-Digital Converter between Two drivers? I am developing battery driver using Windows CE 5.0 and SHARP's ARM9 microprocessor LH7A404. The touch panel driver has already used the Analog-to-Digital Converter of LH7A404, and I don't want to add one more Analog-to-Digital device, so the LH7A404's Analog-to-Digital Converter was used by two driver at the same time. It is really a nightmare. The two driver might use the Analog-to-Digital Converter at the same time and two drivers get the wrong result! So I try to make a globe variable. When the touch panel want to use the Analog-to-Digital Converter, set the variable to "0", and set it to "1" when finish. The battery driver should read the varible before using the Analog-to-Digital Converter. Read "1" means it can use. So where should I put the globle varible or is there a better solution? Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88991
  - 4
    - READ_PORT_BUFFER_UCHAR usage... Hi all, I want to use this function instead of ReadFile in my application because of performance considerations. The problem is that this function doesn't update the port address. I tried to get 16 bytes from the COM2 port. The first 4 bytes i get are true but then it repeats the fifth byte. How can i get around this issue? Do you know of any function other than ReadFile to read from the port? Or can anyone show me how can i use this function to read 16 bytes from the port? Thanks for any help.. Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88985
  - 5
    - Help needed in Installing the WinCE 5.0 driver on CEPC using .cab files for some device Query A: ======== I have successfully installed the driver on CEPC. I have copied driver .dll files in Program files and in windows directory, the required registry keys for loading the driver were also created in CEPC. Now when i connect the Nokia handset with CEPC then it displays a dialog box prompting a user to enter the name of the appropriate USB device driver DLL. When i give the driver name then it tries to find the driver from the host i.e. "J:\WINCE500\PBWorkspaces\cepc_x86\RelDir\CEPC_x86_Debug". It is not trying to find from CEPC. I think as i have already installed the driver then: 1. Why it is not trying to search appropriate registry entries from CEPC 2. Why it is not trying to search appropriate driver from CEPC for this device 3. Why it is showing dialogue box to enter the name of the driver from the host system. Note: First i booted CEPC using the run time image created by Platform builder present on the host system and later i attach the Nokia handset to load the driver for modem device. Query B: ======= I have created the cab file for installing the driver on CEPC using inf file. Now in run time image i provided support for cab installer. I am able to install it from the cab file when i do double click on cab file and after the installation of the driver cab file is deleted automatically. >From platfrom builder 5.0 help i find the following: (Snip) The Wceload tool (Wceload.exe) runs on your target device. You use this tool to install or remove the cab file from a location that you specify. If you do not specify a location, the cab file will be installed in or removed from the default location. The default location is the Program Files directory on your target device. wceload Specifies how it removes the cab file after installation. Value Description 0 Does not remove the cab file. 1 Removes the cab file. This is the default value. 2 Treats the file as chuck blocks of data, and dynamically deletes them. ........ (Snip end) Now please suggest how can i use this wceload.exe tool. When i do double click on this tool it says "Please specify a cab file or double-tap file to install the application" Please suggest whether it is used from command prompt? Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88979
  - 6
    - Help required with PlatBuilder 5.0 on PXA255 Hi ! Others have had this problem before and have posted it in some newsgroups , but there has been no solution yet. I'm building a 5.0 BSP for a platform using the PXA255. The bootloader runs fine and everything is working fine until I try to run the kernel. The processor gets stuck when starting the MMU. I've checked my test code, I've checked my Config.bib .... no visible mistake. Currently I don't have a JTAG debugger (will hopefully have one next week), so I'm stumbling 'round in the darkness a bit, but I have working Test code (kind of complex LED blinker) in two versions (physical and virtual addressing) which works fine before MMU switch, but not afterwards. I tried the same thing with SA1110 (after hacking some makefiles to remove thumb support) and got stuck with the same problem. I know this problem exists with others and if there is anyone out there who discovered the same problem and has a remidy, I would be very thankful for help. Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88977
  - 7
    - Passthru loading problem in CE 5.0 Hi, I am porting IM driver passthru in CE 5.0. I have successfully build the pasthru and loaded in K-Jam(Win CE 5.0). But after installation of passthru and soft reset there will be two instances of WiFi adapter. One is TNETWLN1 and other is PASS\TNETWLN1. This happens everytime. After second reboot instance TNETWLN1 goes away. I want to know does anyone ever encounter same behavior. Are there any other things that has to be done in passthru to get rid of this problem? Thanks Rajat Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88976
  - 8
    - Volume Key and Mobile OS default volume setting bar Dear All, I have a button(key) driver including a Volume Up/Down key controlling. I change the gain value directly by writing register value of audio codec while the volume is pressed. Although I can change the volume in this way, the scrolling bar of OS Desktop volume setting did not act to corresponding volume position. How can I make the volume scrolling icon move when I press the volume key. call waveOutMessage( )?? Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88974
  - 9
    - Re: (Help)(How to identity WinCE Nand storage as Usb Disk) "MikeHan" <hanzn@126.com> ¼¶¼g©ó¶l¥ó·s»D:... > Dear Nicolas & Friends: > > Thank you very much for your reply. I'm very sorry I havn't > descipe this question clear, please see the following: > > --------------------------- > | | > | | > | | > | Resident Flash | > | | > | | > | | > | | > | =================| > | OS | > | | > | =================| > | Loader | > ================== > > Nand Flash > > Now our wince BB board has a large nandflash(2G), but the OS is only > 200M. > > We have make the resident flash as a visiable storage, but I want to > make it as Usb Mass Storage disk when it connecting with PC. > According to the usb driver of Wince, I must operate the resident flash > with the following mode: > > Store_init > Store_Close > DeviceIOControl( Read, write....). > > I don't know how to operate this resident flash and make it as a usb > device on PC. I 'm familar with Usb driver, but I'm not familar with > storage device. > > Please help me thank you very much. > > Best Regards > Mike han > > > > ----- Original Message ----- > From: "Jacky Ko" <JackyKo@discussions.microsoft.com> > Newsgroups: microsoft.public.tw.windowsce > Sent: Friday, August 25, 2006 12:43 AM > Subject: RE: (help)(???WinCE?Nand??????Usb?) > > >> ???????Nand flash???,??block driver???????? >> ??USB???IO???NAND flash????? >> -- >> Jacky Ko >> Microsoft MVP for Windows Embedded >> www.advantech.com >> Advantech Co., Ltd >> >> > > > > Best Regards > Mike Han > > > "Nicolas BESSON" <n_besson@adeneo.adetel_group.com> > ???????:u4smqJ3xGHA.356@TK2MSFTNGP02.phx.gbl... >> Hi Mike, >> >> I'm not sure to understand what you really want to do with this extra >> nand flash area. >> If you want to make it visible under Windows CE as a storage area, you >> have to develop a block device driver. The first step for that kind of >> driver is to implement an FMD to manage the access to the nand flash >> ship. This FMD is used by the FAL to give access to the content of a >> storage area. >> Registry settings are need for your driver to be available by the storage >> manager. >> >> Take a look to that page for detailed steps : >> http://msdn.microsoft.com/library/default.asp?url=/library/en-us/wceddk40/html/cxhowHowToDevelopFlashMediaDriverFMD.asp >> >> >> BR >> >> -- >> ----------------------------------------- >> To reply to me, remove the underscores (_) from my email address (and >> please indicate which newsgroup and message). >> >> Nicolas BESSON >> ADENEO (ADESET) >> Windows Embedded Consultant >> >> MikeHan a écrit : >>> Dear Friends: >>> >>> My WinCE BB has 2G nand flash, but the Code&Data is only 20M, so >>> I have confige the residual space as a storage disk. >>> How can I make this space as Usb Mass Storage disk, I analysis >>> WinCE Usb driver code, and now when device attached to the PC, Usb >>> driver received "Attach" message , for this message, Usb driver need >>> initialize Store(Call Store_Init), but it's fail. >>> >>> Please help me, my good friend, and I believe following the >>> increasing of nand flash, this need will be more and more earnest. >>> >>> Best Regards >>> Mike Han >>> >>> Best Regards >>> Mike Han >> >> -- >> ----------------------------------------- >> To reply to me, remove the underscores (_) from my email address (and >> please indicate which newsgroup and message). >> >> Nicolas BESSON >> ADENEO (ADESET) >> Windows Embedded Consultant > > Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88970
  - 10
    - AYGShell Does anyone know if AYGShell API set depends on Standard shell? I add AYGShell API to my headless OS. It builds successfully but would not run. I wonder it really need a shell or something else to make it work. Thanks. Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88965
  - 11
    - How to use assembly language for ARM? Hi All, From previous postings is looks like Windows CE for ARM processors does not support in-line assemby and that the __asm command is not available. Is there another way to use assembly language in my code for ARM? Any comments or sample source code would be greatly appreciated. Thanks, Richard Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88962
  - 12
    - USB communications fail after RF radition testing We are currently testing a Windows CE 5 based system which uses a USB Host for comms to our custom data collection peripherals. During our RF radiation testing for European CE mark compliance we found that the USB comms would fail and not reconnect. We found that this can be replicated by shorting the data + & - lines on the usb cable with long nose pliers to simulate data scrambling by the RF interferance. This causes the device to lose its enumeration and communications. If you try this whilst connected to an XP based desktop the USB device is lost and then reconnected after the interference stops. On Windows CE the USB does not reconnect. After testing on 2 different CE computers we found that on one removing and reinserting the USB device reestablished the enumeration whereas the other must be rebooted. You can use a memory stick for this simulation. To pass the CE mark test the system must self recover from the RF interferance in the same manner as the XP desktop does. Has anyone experienced this on Windows CE, and if so what settings in the Platform need to be added to ensure that the USB Host comms self repair. Thanks Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88961
  - 13
    - Debug output message Hi: Due to the Serial Debug output commport will be used on the Application, but the ethernet was connected that moment, at lease had loop-back connection. How can I programmatic switch the Debug output message from serial commport to ethernet port, just like KITL switch from serial to VIMINI? Thanks Lu Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88960
  - 14
    - PCMCIA 4.2 to 5.0 Hi I am migrating from Windows CE 4.2 to 5.0. I am having some issues with the PCMCIA driver, I am aware from the help and earlier posts that the pcmcia driver model has changed, due to time constraints I would like to move the pcmcia driver from 4.2 to 5.0 without moving to the bus agnostic driver. cardserv.lib does not exist anymore, so what I have done is copied it from 4.2, my pcmcia driver builds in 5.0 and the pcmcia cards that I have tested ciscioaironet350 for example work, the only problem that I am having is that CF memory cards used with a pcmcia adapter are not recognised anymore. Firstly is what I have done above correct and secondly any ideas why the compact flash card is not recognised. Regards Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88953
  - 15
    - Filter driver Hi, I just built an emulator and added msfilter and waveui. I can see ACM1: comes up but how can I activate this filter? In the wave ui, there seems to be a filter selection UI but that UI doesn't bring up. Many thanks in advance, Jay. Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88952
  - 16
    - NDIS driver MiniportSend doubt Hi. I am trying to write an NDIS driver. I have followed the NDIS sample from %_WINCEROOT%\Public\Common\Oak\Drivers\Netcard\NE2000. I manage to receive packets in MiniportSend, but I only receive a packet with one buffer, no matter the size of the data I am sending (I am sending an UDP packet). The packet received contains the source ip address and destination ip address (and a few more things), but I can't find the data I am sending, the length of the buffer is always 0x2a. Is this normal, is the data stored somewhere else? Here is the data I am receiving. 0003EF80 FF FF FF FF FF FF 00 00 0003EF88 AC 10 5A 97 08 06 00 01 0003EF90 08 00 06 04 00 01 00 00 0003EF98 AC 10 5A 97 AC 10 5A 97 0003EFA0 00 00 00 00 00 00 AC 10 0003EFA8 65 2C Source IP â?? AC 10 5A 97 Destination IP - AC 10 65 2C Thanks in advanced. Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88950
  - 17
    - Active sync over Serial Hi, What are the steps needed for active sync over serial in Windows Mobile. Active sync over IR is working fine in Windows Mobile. (In windows mobile, active sync application has the option to connect over IR). In windows CE, first we will make a new connection, using Dial up and Networking from Control panel, over the specified serial port and will make that connection as default. Do we have anything similar in Windows Mobile. Thanks in advance, San Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88943
  - 18
    - UART issue Hi, I have a hardware which has 5 UARTs and one of them is used for slow IR. In windows CE, all the UARTs are working. But when I tried in Windows Mobile with the same hardware, one UART is not working. While debugging I have seen that driver is writing the data to the FIFO but data is coming to the hyper terminal. What could be the issue. Is ther any limitation or known issue with the number of UARTs in Windows Mobile. Let me know your comments. Thanks in Advance, San Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88942
  - 19
    - USB 2.0 hub doesn't work on WinCE 5.0 Hi, I am new to WinCE and have trouble to make USB 2.0 hub working. My platform is Geode NX, SiS 741/946. Working USB devices : keyboard, mouse, 2.0 USB diskonkey. 1.1 hub and devices below it. Non-working USB devices : USB 2.0 hub (self-powered and bus-powered) What I found until now is, it takes several seconds in ExternalHub::GetStatusChangeBitmap. And dwBytesTransferred is 0. Where should I begin debugging? Thanks in advance. Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88939
  - 20
    - missing 91c111 interrupts Hello, I have a CE 4.2 SH3 platform with IRQ0 set as a rising-edge triggered interrupt that is connected to the INT0 pin on a SMSC91C111 ethernet chip. Under high traffic conditions the chip is resetting. I searched this newsgroups and read the postings regarding this issue on this chip and I plan to implement the fix that involves checking the status of the interrupt from the OAL prior to re-enabling the interrupt and setting the IST event so that a "missed" rising edge will be serviced anyway. I was thinking this must be done in OEMInterruptEnable(). What API(s) exist to find out what event handle NDIS has set up to service the IST so that I can set the event myself when this condition occurs? Any advice is appreciated. Cheers, Ken Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88938
  - 21
    - Could not play MP3 radio stream with WinCE 5.0 media player When I try to open a MP3 radio stream in Windows CE Media Player, I receive this error message: "The server received invalid data from the client on the control connection. ( 0xc00d0032 ). I searched the internet for this error message. According this site: "http://www.narrowstep.com/playerhelp/index.html?wmp_error_0xc00d0032.htm" it means that I should open a specific UDP port on my firewall, but I do not use any firewall in my WinCE os. In fact, I am able to play MP3 radio streams from my XP PC on the same network. I am using Windows CE 5.0. My OSDesign contains all available audio/video codecs and all available Media features from the catalog, including "WMA and MP3 streaming". These are the MP3 radiostreams I use for testing: - http://81.173.3.132:80/ - http://shoutcast.omroep.nl:8022/ Does anybody know what is wrong here? Debugmessages from quartzlib: 1030609 PID:22c70872 TID:42cd0182 CHttpStream::CreateInstance(): Entering. 1030609 PID:22c70872 TID:42cd0182 CHttpStream::GrokStreamName(): Entering. 1030609 PID:22c70872 TID:42cd0182 CHttpStream::GrokStreamName(): Leaving. 1030609 PID:22c70872 TID:42cd0182 CMediaStreamBase::CMediaStreamBase: Entering. 1030610 PID:22c70872 TID:42cd0182 CMediaStreamBase@00070970::ctor: entry, pMonitor=0006FF54 1030610 PID:22c70872 TID:42cd0182 CMediaStreamBase@00070970::GetBandwidthInfo could not find ManualBandwidth. 1030610 PID:22c70872 TID:42cd0182 CPacketPairHistory@00070DF8::Initialize could not find previous IP address. 1030611 PID:22c70872 TID:42cd0182 CMediaStreamBase@00070970::ctor: exit 1030611 PID:22c70872 TID:42cd0182 CMediaStreamBase::CMediaStreamBase: Leaving. 1030611 PID:22c70872 TID:42cd0182 CHttpStream::CHttpStream(): Entering. 1030611 PID:22c70872 TID:42cd0182 CHttpStream::CHttpStream()@00070970 ctor entry. 1030612 PID:22c70872 TID:42cd0182 CHttpStream::CHttpStream()@00070970: m_fFauxOpen = FALSE 1030612 PID:22c70872 TID:42cd0182 CHttpStream::CHttpStream()@00070970: m_fReconnect = FALSE 1030612 PID:22c70872 TID:42cd0182 CHttpStream::_init_post(): Entering. 1030612 PID:22c70872 TID:42cd0182 CHttpStream::_init_post(): Leaving. 1030612 PID:22c70872 TID:42cd0182 CHttpStream::_per_connection_init(): Entering. 1030612 PID:22c70872 TID:42cd0182 CHttpStream::_per_connection_init()@00070970: m_fFauxOpen = FALSE 1030612 PID:22c70872 TID:42cd0182 CHttpStream::_init_post(): Entering. 1030612 PID:22c70872 TID:42cd0182 CHttpStream::_init_post(): Leaving. 1030613 PID:22c70872 TID:42cd0182 CHttpStream::_per_connection_init()@00070970: m_fReconnect = FALSE 1030613 PID:22c70872 TID:42cd0182 CHttpStream::_per_connection_init(): Leaving. 1030613 PID:22c70872 TID:42cd0182 CHttpStream::Configure(): Entering. 1030614 PID:22c70872 TID:42cd0182 CHttpStream::Configure(): Leaving. 1030614 PID:22c70872 TID:42cd0182 CHttpStream::CHttpStream()@00070970::ctor: exit 1030615 PID:22c70872 TID:42cd0182 CHttpStream::CHttpStream(): Leaving. 1030617 PID:22c70872 TID:42cd0182 CHttpStream::CreateInstance(): Leaving. 1030617 PID:22c70872 TID:42cd0182 CBwController::ComputeDataRates(): Reduce thresh 1200, Increase thresh 2400 1030617 PID:22c70872 TID:42cd0182 CHttpStream::InternalQueryInterface(): Entering. 1030617 PID:22c70872 TID:42cd0182 CHttpStream::InternalQueryInterface(): Leaving. 1030617 PID:22c70872 TID:42cd0182 CHttpStream::Open(): Entering. 1030618 PID:22c70872 TID:42cd0182 CHttpStream::Open()@00070970:http://81.173.3.132:80/ 1030619 PID:22c70872 TID:42cd0182 CHttpStream::GrokStreamName(): Entering. 1030619 PID:22c70872 TID:42cd0182 CHttpStream::GrokStreamName(): Leaving. 1030620 PID:22c70872 TID:42cd0182 CHttpStream::GetProxyInfo(): Entering. 1030621 PID:22c70872 TID:42cd0182 0x82be0800: IE 5.5 GetConnectedState failed! 1030621 PID:22c70872 TID:42cd0182 0x82be0800: Proxy-settings for host 81.173.3.132:80 = DIRECT 1030621 PID:22c70872 TID:42cd0182 CHttpStream::GetProxyInfo(): Leaving. 1030621 PID:22c70872 TID:42cd0182 CHttpStream::Open()@00070970: Posting locating server message to monitor 1030621 PID:22c70872 TID:42cd0182 CHttpStream::Open(): Leaving. 1030623 PID:22c70872 TID:c32f7832 CHttpStream::CatchUnprocessedMessage(): Entering. 1030623 PID:22c70872 TID:c32f7832 CHttpStream::ContinueOpen(): Entering. 1030623 PID:22c70872 TID:c32f7832 CHttpStream::ContinueOpen()@00070970::about to request connection 1030885 PID:22c70872 TID:c32f7832 CHttpStream::ContinueOpen()@00070970: Posting connecting to server message to monitor 1030885 PID:22c70872 TID:c32f7832 CHttpStream::ContinueOpen(): Leaving. 1030885 PID:22c70872 TID:c32f7832 CHttpStream::CatchUnprocessedMessage(): Leaving. 1030890 PID:22c70872 TID:c32f7832 CHttpStream::CatchUnprocessedMessage(): Entering. 1030890 PID:22c70872 TID:c32f7832 CHttpStream::CatchUnprocessedMessage()@00070970: rcvd FD_CONNECT state = 2 1030890 PID:22c70872 TID:c32f7832 CHttpStream::OnConnectEvent(): Entering. 1030890 PID:22c70872 TID:c32f7832 CHttpStream::SendGetRequest(): Entering. 1030890 PID:22c70872 TID:c32f7832 CHttpStream::SetStreamPos(): Entering. 1030890 PID:22c70872 TID:c32f7832 CHttpStream::SetStreamPos(): Leaving. 1030891 PID:22c70872 TID:c32f7832 CHttpStream::AppendAuthenticationHeaders(): Entering. 1030891 PID:22c70872 TID:c32f7832 CHttpStream::AppendAuthenticationHeaders(): Leaving. 1030891 PID:22c70872 TID:c32f7832 CHttpStream::SendControlMessage(): Entering. 1030891 PID:22c70872 TID:c32f7832 CHttpStream::SendControlMessage():@00070970::sending msg: GET / HTTP/1.0 Accept: */* User-Agent: NSPlayer/8.0.0.0 Host: 81.173.3.132:80 Pragma: no-cache,rate=1.000000,stream-time=0,stream-offset=0:0,request-context=1,max-duration=0 Supported: com.mic 1030891 PID:22c70872 TID:c32f7832 CHttpStream::SendControlMessage(): Leaving. 1030892 PID:22c70872 TID:c32f7832 CHttpStream::SendGetRequest(): Leaving. 1030892 PID:22c70872 TID:c32f7832 CHttpStream::OnConnectEvent(): Leaving. 1030892 PID:22c70872 TID:c32f7832 CHttpStream::CatchUnprocessedMessage(): Leaving. 1031233 PID:22c70872 TID:e3318d86 CHttpStream::HandleReadSocket(): Entering. 1031233 PID:22c70872 TID:e3318d86 CHttpStream::ReceiveControlMessage(): Entering. 1031233 PID:22c70872 TID:e3318d86 CHttpStream::ReceiveControlBytes(): Entering. 1031233 PID:22c70872 TID:e3318d86 CHttpStream::ReceiveControlBytes(): Leaving. 1031233 PID:22c70872 TID:e3318d86 CHttpStream::ReceiveGetResponse(): Entering. 1031233 PID:22c70872 TID:e3318d86 CHttpStream::ReceiveControlBytes(): Entering. 1031233 PID:22c70872 TID:e3318d86 CHttpStream::ReceiveControlBytes(): Leaving. 1031234 PID:22c70872 TID:e3318d86 CHttpStream::ReceiveGetResponse(): Leaving. 1031234 PID:22c70872 TID:e3318d86 CHttpStream::ReceiveControlMessage(): Leaving. 1031234 PID:22c70872 TID:e3318d86 CHttpStream::HandleReadSocket(): Leaving. 1031234 PID:22c70872 TID:e3318d86 CHttpStream::HandleReadSocket(): Entering. 1031234 PID:22c70872 TID:e3318d86 CHttpStream::ReceiveControlMessage(): Entering. 1031234 PID:22c70872 TID:e3318d86 CHttpStream::ReceiveGetResponse(): Entering. 1031234 PID:22c70872 TID:e3318d86 CHttpStream::ReceiveControlBytes(): Entering. 1031235 PID:22c70872 TID:e3318d86 CHttpStream::ReceiveControlBytes(): Leaving. 1031235 PID:22c70872 TID:e3318d86 CHttpStream::OnGetResponse(): Entering. 1031235 PID:22c70872 TID:e3318d86 CHttpStream::OnGetResponse(): Leaving. 1031235 PID:22c70872 TID:e3318d86 CHttpStream::ReceiveGetResponse(): Leaving. 1031235 PID:22c70872 TID:e3318d86 CHttpStream::ReceiveControlMessage(): Leaving. 1031235 PID:22c70872 TID:e3318d86 CHttpStream::ReallyShutdown(): Entering. 1031235 PID:22c70872 TID:e3318d86 CHttpStream::ReallyShutdown()@00070970: entering with hr = 0xc00d0032 1031236 PID:22c70872 TID:e3318d86 CHttpStream::ReallyShutdown()@00070970: Posting Open message to monitor hr = 0xc00d0032, dwUserContext = 1 1031236 PID:22c70872 TID:e3318d86 CHttpStream::_per_connection_init(): Entering. 1031236 PID:22c70872 TID:e3318d86 CHttpStream::_per_connection_init()@00070970: m_fFauxOpen = FALSE 1031236 PID:22c70872 TID:e3318d86 CHttpStream::_init_post(): Entering. 1031236 PID:22c70872 TID:e3318d86 CHttpStream::_init_post(): Leaving. 1031236 PID:22c70872 TID:e3318d86 CHttpStream::_per_connection_init()@00070970: m_fReconnect = FALSE 1031236 PID:22c70872 TID:e3318d86 CHttpStream::_per_connection_init(): Leaving. 1031236 PID:22c70872 TID:e3318d86 CHttpStream::_cleanup(): Entering. 1031236 PID:22c70872 TID:e3318d86 CHttpStream::ResetHeaderAssembler(): Entering. 1031236 PID:22c70872 TID:e3318d86 CHttpStream::ResetHeaderAssembler(): Leaving. 1031237 PID:22c70872 TID:e3318d86 CHttpStream::CleanupDatagramQueue(): Entering. 1031237 PID:22c70872 TID:e3318d86 CHttpStream::CleanupDatagramQueue()@00070970: Cleanup 1031237 PID:22c70872 TID:e3318d86 CHttpStream::DequeueDatagram(): Entering. 1031237 PID:22c70872 TID:e3318d86 CHttpStream::DequeueDatagram(): Leaving. 1031237 PID:22c70872 TID:e3318d86 CHttpStream::CleanupDatagramQueue(): Leaving. 1031237 PID:22c70872 TID:e3318d86 CHttpStream::_cleanup(): Leaving. 1031237 PID:22c70872 TID:42cd0182 CNSSource::Failure(0XC00D0032) 1031238 PID:22c70872 TID:42cd0182 CHttpStream::Close(): Entering. 1031238 PID:22c70872 TID:42cd0182 CHttpStream::Close()@00070970: Entering 1031243 PID:22c70872 TID:42cd0182 CHttpStream::Close()@00070970: returning NS_E_INVALID_REQUEST m_State = 1 1031243 PID:22c70872 TID:42cd0182 CHttpStream::Close(): Leaving. 1031243 PID:22c70872 TID:42cd0182 CHttpStream::~CHttpStream(): Entering. 1031243 PID:22c70872 TID:42cd0182 CHttpStream::~CHttpStream()@00070970::dtor: entry 1031243 PID:22c70872 TID:42cd0182 CHttpStream::ReallyShutdown(): Entering. 1031243 PID:22c70872 TID:42cd0182 CHttpStream::ReallyShutdown()@00070970: entering with hr = 0xc00d002a 1031244 PID:22c70872 TID:42cd0182 CHttpStream::ReallyShutdown()@00070970: m_State is READY, hr = 0xc00d002a, dwUserContext = 1 1031244 PID:22c70872 TID:42cd0182 CHttpStream::ReallyShutdown(): Leaving. 1031244 PID:22c70872 TID:42cd0182 CHttpStream::~CHttpStream(): Leaving. 1031244 PID:22c70872 TID:42cd0182 CMediaStreamBase@00070970::dtor: entry 1031237 PID:22c70872 TID:e3318d86 CHttpStream::ReallyShutdown(): Leaving. 1031244 PID:22c70872 TID:e3318d86 CHttpStream::HandleReadSocket(): Leaving. 1031246 PID:22c70872 TID:42cd0182 CMediaStreamBase@00070970::dtor: this is not the message pump thread 1031246 PID:22c70872 TID:42cd0182 CMediaStreamBase@00070970::dtor: exit Nick Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88937
  - 22
    - (Help)(How to identity WinCE Nand storage as Usb Disk) Dear Friends: My WinCE BB has 2G nand flash, but the Code&Data is only 20M, so I have confige the residual space as a storage disk. How can I make this space as Usb Mass Storage disk, I analysis WinCE Usb driver code, and now when device attached to the PC, Usb driver received "Attach" message , for this message, Usb driver need initialize Store(Call Store_Init), but it's fail. Please help me, my good friend, and I believe following the increasing of nand flash, this need will be more and more earnest. Best Regards Mike Han Best Regards Mike Han Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88930
  - 23
    - RAS Server User Credentials Hiho! I'm writing an administration tool for the WinCE-RAS-Server. The RasIOControl-function provides setting and removing user-credentials. Is it possible to read those information? I just want to get a list of the allowed usernames. I don't mind the passwords. Has anybody an idea how to do that? I already thought about the CredRead-function but I didn't find information what to enter for the target-string. Thank for your help! Regards, DennisB Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88929
  - 24
    - why I can't install program on device by activesync? I want to install some program on pocket pc by activesync. but there exists some problem. One is that when I excute Add/Remove Programs in ActiveSync tools, this program is waiting for ever. The other is that this program can excute, but when installing program,it would show" The mobile device is no longer connected. please connect the device and run Application Manager again. On device, It shows that there is a problem on rapiclnt.exe, please report these to microsoft. Form debug info , The rapiclnt.exe has aborted. who can help me? Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88928
  - 25
    - Serial driver- 16 byte FIFO usage! Hi all, I am working on serial communication and my problem is that the CPU usage is about 90% during serial communication. For this reason, i want to improve performance by using the 16 byte FIFO of 16C84(or whatever the integrated circuit used for serial communication). How can i efficiently use this FIFO in program? I mean do you know of a way to get 16 bytes in FIFO in 1 step rather than in 16 steps? Any help is greatly appreciated... Thanks... Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88925
- Next
  - 1
    - sdmmc porting problem report Hi, all I've got problems with porting the sdmmc 1.x driver from WCE 4.2 to WCE (windows mobile) 5.0. There is just little time given to me. Plz, help me. Is it possible to port the sdmmc to WCE 5.x in a short time? The below is the problem list. [Problem List] 1. At first, I got some problems when I ported it at Debug mode. One of them was my device was halted and it didn't work again. But after building by releas mode, it seemed to work fine... maybe not I think now. --> anyone knows why? 2. Finally I found that a card was detected and I was able to see the folder, "Storage Card". But I found out that the driver reported an error (ERROR_WRITE_PROTECT) due to the SD hardware protection, but the OS didn't show up any message. The driver calls SetLastError(ERROR_WRITE_PROTECT) but no answer.. I guess it seems not to notice other errors as well. --> plz, help me.. it's driving me crazy. Is it related to the problem number 3 below? 3. GetStorageID error I've seen several lists with the problem but little bit different except the list below. Plz, answer how to solve it. --> jojje! Have you found the answer. ------------------------------------------------------------------------------ ------------------------ Hi, I've seen discussions about GetStorageID here before, but not exactly this error maybe. In the SDMemory driver (in file sdmemmain.cpp, function GetStorageID) the following check of buffer space fails: if( cBytes < (sizeof(*psid)+SD_SIZEOF_STORAGE_ID) ) GetStorageID return ERROR_INVALID_PARAMETER. cBytes is determined by COREOS\STORAGE\STOREMGR\store.cpp and is set to sizeof (STORAGE_IDENTIFICATION) (=16 bytes). SD_SIZEOF_STORAGE_ID is 12 and sizeof(*psid) is 16, so this check will fail. What should I do? I'm using CE 5.0 on a Samsung s3c2410 platform. Thanks, Jojje ------------------------------------------------------------------------------ ----------------------------------------------- Thank you! Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88922
  - 2
    - Take long time to detect and recognize USB storage device I believe this issue has been raised quite a few times. We have been dismissing it as a problem associated with USB storage device's controller and/or firmware. Recently, one of our customer raised this issue again. As the result, I spent some time to investigate and done some testing. I found that "Hive-based" registry support component is causing the delay in detecting and recogniztion USB storage device. When I built a WinCE 5.0 image WITHOUT "Hive-based" registry support, the system can detect and recognize USB flash storage device almost instantly. When I built a WinCE 5.0 image WITH "Hive-based" registry support, it takes the system more than 90 seconds to detect and recognize the very same USB flash storage device. I verified the above behavior on two separate x86 based system with different CPU. The above behavior is consistence on both system. 1. eBox-II using ICOP_Vortex86 BSP 2. Via Eden system using ViaCN BSP I use "Internet Appliance" template with the default components to build the image with the following components added. - ATAPI Block driver - FAT file system - USB Storage Class driver - Hive-based registry (excluded in some of the builts) ---------------------------------------------------------------------------------------------------------------------- I am hoping that some of you out there experienced similar problem, found a solution and willing to share with everyone here. Best Regards, Samuel Phung ICOP Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88917
  - 3
    - Format a partition I am trying to make a program to format a drive or partition. But the call to FormatPartition() is always failed. Can someone take a look at my code following and tell me what I did wrong? What I did here is to find a partition matching "szDrive" and then format it. Thanks. void FormatDisk(TCHAR* szDrive) { STOREINFO si; si.cbSize = sizeof(STOREINFO); HANDLE hss = FindFirstStore(&si); if(hss == INVALID_HANDLE_VALUE) { printf("FindFirstStore failed.\n"); return; } do { wprintf(L"%s, %s, %s.\n", si.szDeviceName, si.szStoreName, si.sdi.szProfile); HANDLE hStore = OpenStore(si.szDeviceName); if(hStore != INVALID_HANDLE_VALUE) { PARTINFO pi; pi.cbSize = sizeof(PARTINFO); HANDLE hsp = FindFirstPartition(hStore, &pi); if(hsp != INVALID_HANDLE_VALUE) { do { wprintf(L"%s, %s.\n", pi.szPartitionName, pi.szVolumeName); HANDLE hPar = OpenPartition(hStore, pi.szPartitionName); if(hPar != INVALID_HANDLE_VALUE) { if(_wcsicmp(szDrive, pi.szVolumeName) == 0) { wprintf(L"DismountPartition: %d.\n", DismountPartition(hPar)); //Always return false wprintf(L"FormatPartition: %d.\n", FormatPartition(hPar)); wprintf(L"MountPartion: %d.\n", MountPartition(hPar)); } CloseHandle(hPar); } } while(FindNextPartition(hsp, &pi)); FindClosePartition(hsp); } } CloseHandle(hStore); wprintf(L"-----------------------------\n"); } while(FindNextStore(hss, &si)); FindCloseStore(hss); } Best regards, Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88916
  - 4
    - DirectDraw CETK Failures Hi, I am porting the existing MQ1188 CE4.2 display to CE5.0. It is DDraw based and I had to remove some stuff from it because the DirectDraw in CE5.0 does not support some functions/struct/etc. anymore. Anyway, the driver is operable for general use but it fails CETK DDraw test. Here is one of the outputs of a subtest that fails: 14324475: BEGIN TEST: "Blt" 14324497: Video driver in use is DDI.DLL 14324510: Using NORMAL Cooperative Level 14324530: Creating Global DirectDraw Singleton 14324573: Testing Source Surface : Primary with 0 backbuffers - (Unspecified Pixel Format) 14324609: Creating Global Primary DirectDrawSurface Singleton 14324630: Creating DirectDrawSurface Singleton 14324647: Creating and attaching a clipper 14324665: Testing Source Surface : Primary 14324691: Surface Unsupported 14324704: Surface Unsupported 14324717: Surface Unsupported 14324730: Testing Destination Surface : Offscreen surface in video memory - (Unspecified Pixel Format) 14324766: Got OOM error creating surface (DDERR_OUTOFMEMORY) 14324788: Done Destination 14324801: Testing Destination Surface : Offscreen surface in system memory - (Unspecified Pixel Format) 14324836: Overlay not supported ... Skipping 14324856: Done Destination 14324868: Testing Destination == Source 14324900: Test will copy from (top,left,bottom, right) (33,7,113,67) 14324926: To (top,left,bottom, right) (26,0,106,60) 14324949: Data Abort: Thread=87bc1400 Proc=88027c20 'tux.exe' 14324967: AKY=00000401 PC=00f8bb70(ddrawtk.dll+0x0002bb70) RA=00183dee(tux.exe+0x00173dee) BVA=16183dee FSR=00000007 14325015: END TEST: "Blt" I am wondering what causes the test to fail. Any suggestions are greatly appreciated. Thanks in advance. PK Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88910
  - 5
    - Install 5's QFEs or not? Are the QFEs necessary? Is installing them preferred? It seems significant changes have been made. If somebody is supplying me code, should I expect it to work properly with all QFEs installed, or none installed? -- #include <standard.disclaimer> _ Kevin D Quitt USA 91387-4454 96.37% of all statistics are made up Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88904
  - 6
    - About USB KITL function in EBOOT I am trying to develop usb_rdnis_kitl instead of Ethernet_kitl in EBOOT.I want to use usb interrupt mode to realize.But even to now i can not receive the interrupt.I want to identify whether i am right.Can i use usb interrupt mode in eboot? Thanks Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88898
  - 7
    - Does DirectShow support VBR in Windows CE 5.0? Hi, I used DirectShow to write a MP3 player. I found it is OK for playing CBR mp3 files. For some VRB mp3 files, we met some strange problems. For example: Music time length is not correct. Does DirectShow of Windows CE support all VBR mp3 files ? Thanks. Yu. Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88890
  - 8
    - Help needed in creating installation utility for Installing the WinCE 5.0 driver on CEPC using .cab files for some device I am using WinCE 5.0 and I have one system CEPC that has pentium II. I have created some modem device driver on windows ce 5.0. I want to create some installation utility to install the wince driver on CEPC using .cab files. I have created .cab file using .inf file and CabWizard utility. Now I have Installed ActiveSync 4.2 in my system as i find that CEAppMgr.exe" is a component of ActiveSync, specifically the agent which handles the transfer of CAB files onto the device. It has created the following registry entries in the host system. HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\App Paths\CEAPPMGR.EXE. I have also created .ini file that describes which .cab files correspond to which platform Now still i am not getting how to use CEAppMgr and my .cab files to install the driver on CEPC for some handset. I find one setup.exe file that facilitates in installing the driver and uses the .ini file as a command line argument. Reference: http://www.pocketpcdn.com/articles/creatingsetup.html When i execute this I am getting the message "Application Manage can run only when a mobile device is connected" Although i have booted the CEPC using run time image created on my host system and also attached the nokia handset to install the driver, then why i am getting the dialogue "Application Manage can run only when a mobile device is connected" Please suggest me..... Thanx for your suggestions in advance Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88888
  - 9
    - FAILED TO LAUNCH WINCE IMAGE PROPERLY Hello Everybody, I am using Platform builder 5.0 to create a wince image for a device based on intel PXA255 architecture. I already built images for this target and managed to load it, program it into flash and run it. The problem is that the other day I added support for .NET CF2 and since then I cannot boot the device properly. I have retruned back to my first image (that used to work) but I observe the same behavior. I join to this post some debbuging messages if it can help.. The strange thing is the following : when the system is booting, and I am using the debbuger, after the system is started I can run programms from platform builder like repllog or ip config, I can watch the running processes and threads too, but since I get this "4294838867 PID:634a25da TID:33e38f2 0x83378c28: LanaUp: (NB) pLana 378C00 (1) up Addr E71DFEA9 Mask FFFF Bcast FFFFFEA9" debug line I cannot communicate with the target anymore... If anyone could help.. Debbuging messages : 4294806832 PID:c31886c2 TID:3074b46 0x8306c400: [TIMESVC DST] System Started... 4294806860 PID:c31886c2 TID:3074b46 0x8306c400: [NOTIFY] CeRunAppAtEvent - clearing system event registration for \\.\Notifications\NamedEvents\DSTTzChange 4294806862 PID:c31886c2 TID:3074b46 0x8306c400: [NOTIFY] CeRunAppAtEvent - clearing system event registration for \\.\Notifications\NamedEvents\DSTTimeChange 4294806864 PID:c31886c2 TID:3074b46 0x8306c400: [NOTIFY] RemoveAppRunAtTime::Starting Database Sweep... 4294806882 PID:c31886c2 TID:3074b46 0x8306c400: [NOTIFY] SetUserNotification (or replacing 00000000) 4294806882 PID:c31886c2 TID:3074b46 0x8306c400: [NOTIFY] SetUserNotification::Registring system watch: event 12 app \\.\Notifications\NamedEvents\DSTTzChange args AppRunAfterTzChange 4294806892 PID:c31886c2 TID:3074b46 0x8306c400: [NOTIFY] SetUserNotification (or replacing 00000000) 4294806893 PID:c31886c2 TID:3074b46 0x8306c400: [NOTIFY] SetUserNotification::Registring system watch: event 1 app \\.\Notifications\NamedEvents\DSTTimeChange args AppRunAfterTimeChange 4294806911 PID:c31886c2 TID:3074b46 0x8306c400: [NOTIFY] RemoveAppRunAtTime::Starting Database Sweep... 4294806912 PID:c31886c2 TID:3074b46 0x8306c400: [NOTIFY] SetUserNotification (or replacing 00000000) 4294806919 PID:c31886c2 TID:3074b46 0x8306c400: [NOTIFY] SetUserNotification::Setting event semaphore 4294806919 PID:c31886c2 TID:3074b46 0x8306c400: [NOTIFY] ProcessDatabase::started at local time 08/23/2006 09:20:50 4294807086 PID:c31886c2 TID:c309d152 0x830b29b0: HTTPD: Initializing log files 4294807106 PID:c31886c2 TID:c309d152 0x830b29b0: >>> Loading module secur32.dll at address 0x03920000-0x03929000 (RW data at 0x01F98000-0x01F9852C) 4294807118 PID:c31886c2 TID:c309d152 0x830b29b0: SECUR32: Loading package DLL: 'schannel.dll'. 4294807120 PID:c31886c2 TID:c309d152 0x830b29b0: >>> Loading module crypt32.dll at address 0x03180000-0x031FE000 (RW data at 0x01F03000-0x01F04031) 4294807123 PID:c31886c2 TID:c309d152 0x830b29b0: >>> Loading module schannel.dll at address 0x038E0000-0x0391E000 (RW data at 0x01F95000-0x01F96294) 4294807376 PID:c31886c2 TID:c309d152 0x830b29b0: SECUR32: Loading package DLL: 'ntlmssp.dll'. 4294807377 PID:c31886c2 TID:c309d152 0x830b29b0: SECUR32: Loading package DLL: 'kerberos.dll'. 4294807377 PID:c31886c2 TID:c309d152 0x830b29b0: SECUR32: Loading package DLL: 'spnego.dll'. 4294807379 PID:c31886c2 TID:c309d152 0x830b29b0: >>> Loading module spnego.dll at address 0x036F0000-0x03708000 (RW data at 0x01F65000-0x01F65EF0) 4294807441 PID:c31886c2 TID:c309d152 0x830b29b0: SECUR32: Package [1] loaded -- 'Microsoft Unified Security Protocol Provider' 4294807444 PID:c31886c2 TID:c309d152 0x830b29b0: SECUR32: Package [2] loaded -- 'Microsoft TLS 1.0' 4294807447 PID:c31886c2 TID:c309d152 0x830b29b0: SECUR32: Package [3] loaded -- 'Microsoft SSL 3.0' 4294807450 PID:c31886c2 TID:c309d152 0x830b29b0: SECUR32: Package [4] loaded -- 'Microsoft SSL 2.0' 4294807453 PID:c31886c2 TID:c309d152 0x830b29b0: SECUR32: Package [5] loaded -- 'NTLM' 4294807456 PID:c31886c2 TID:c309d152 0x830b29b0: SECUR32: Package [6] loaded -- 'Kerberos' 4294807459 PID:c31886c2 TID:c309d152 0x830b29b0: SECUR32: Package [7] loaded -- 'Negotiate' 4294807459 PID:c31886c2 TID:c309d152 0x830b29b0: SECUR32: Locating package 'NTLM' ... 4294807460 PID:c31886c2 TID:c309d152 0x830b29b0: found (0x0004F3F0). 4294807480 PID:634a25da TID:33e38f2 0x83378c28: VMini:: Detected DHCP [DISCOVER] 4294809921 PID:634a25da TID:33e38f2 0x83378c28: VMini:: Detected DHCP [DISCOVER] 4294814855 PID:634a25da TID:33e38f2 0x83378c28: VMini:: Detected DHCP [DISCOVER] 4294822857 PID:634a25da TID:33e38f2 0x83378c28: GetDhcpLease(VMINI1): failed badly! 4294823223 PID:634a25da TID:33e38f2 0x83378c28: VMini:: Detected DHCP [DISCOVER] 4294824231 PID:634a25da TID:33e38f2 0x83378c28: VMini:: Detected DHCP [DISCOVER] 4294826925 PID:634a25da TID:33e38f2 0x83378c28: VMini:: Detected DHCP [DISCOVER] 4294830933 PID:634a25da TID:33e38f2 0x83378c28: VMini:: Detected DHCP [DISCOVER] 4294838867 PID:634a25da TID:33e38f2 0x83378c28: LanaUp: (NB) pLana 378C00 (1) up Addr E71DFEA9 Mask FFFF Bcast FFFFFEA9 I also have these messages : !AFD: Unable to load library 'irdastk.dll' 4294791596 PID:634a25da TID:63487f5e 0x834a44e4: !AFD: Unable to load library 'btd.dll' 4294791597 PID:634a25da TID:63487f5e 0x834a44e4: !AFD: Unable to GetProcAddress of ReadyToGo in 'Netbios' 4294791598 PID:634a25da TID:63487f5e 0x834a44e4: !AFD: Unable to GetProcAddress of ReadyToGo in 'Redir' 4294791598 PID:634a25da TID:63487f5e 0x834a44e4: !AFD: Unable to GetProcAddress of ReadyToGo in 'Dhcp' 4294791614 PID:634a25da TID:63487f5e 0x834a44e4: !AFD: Unable to load library 'IPNat.dll' 4294791614 PID:634a25da TID:63487f5e 0x834a44e4: !AFD: Unable to GetProcAddress of ReadyToGo in 'Ws2Instl' or FSD_MountDisk: mounting volumes for hDsk=000BAC70 4294792375 PID:234a14ee TID:34872f6 0x834a1000: FATFS!OpenVolume: access time updates disabled 4294792375 PID:234a14ee TID:34872f6 0x834a1000: FATFS!OpenVolume: event logging enabled 4294792375 PID:234a14ee TID:34872f6 0x834a1000: FATFS!OpenVolume: automatic scanning disabled 4294792375 PID:234a14ee TID:34872f6 0x834a1000: FATFS!OpenVolume: write verify disabled 4294792375 PID:234a14ee TID:34872f6 0x834a1000: FATFS!OpenVolume: extra FAT on format disabled 4294792375 PID:234a14ee TID:34872f6 0x834a1000: FATFS!OpenVolume: force write through enabled 4294792378 PID:234a14ee TID:34872f6 0x834a1000: FATFS!OpenVolume: Codepage = 1 4294792380 PID:234a14ee TID:34872f6 0x834a1000: FATFS!OpenVolume: Number of path cache entries = 50 4294792382 PID:234a14ee TID:34872f6 0x834a1000: FATFS!InitVolume: driver reports fewer sectors than BPB! (12347 vs. 12851) Best regards Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88886
  - 10
    - HCD default IST priority? Hi all, I am examining a usb host driver in CE5. There is a place that the program does qurey for IST priority. ******************************************************** RegQueryValueEx( hActiveKey, TEXT("Priority256"), NULL, &valType, (PUCCHAR)&priority, &valLength ) ******************************************************** here hActiveKey point to HLM\Drivers\Active\27, and has the content ******************************************************** [HKEY_LOCAL_MACHINE\Drivers\Active\27] "Hnd"=dword:000569e0 "Name"="HCD3:" "Key"="Drivers\\BuiltIn\\HCD_FSH1" "BusParent"=dword:00030da0 "InterfaceType"=dword:00000000 "BusName"="BuiltInPhase1_0_23_0" ******************************************************** As can be seen, no "Priority256" is in it. But the RegQueryValueEx get a value 0x65(101) to priority, how this value is retrieved, is it the default value for HCD type driver? Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88884
  - 11
    - Virtual keyboard in WinCE based devices Our project has a touch display which has a GUI. Our problem is whenever any edit box is opened for editing character 3 is cont. sent to the edit box has an input. Even normally on the WinCE desktop if we 1. click RUN in the start menu or 2. rename a file etc... for all these functions char 3 will be cont fed to the editable box thanks n advance mkm Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88878
  - 12
    - USB Communication Device Class(CDC) Hello Everybody, I have device which can communicate wth with USB Communication device class only, I check on MSDN RNDIS driver has support of CDC so I have include it with my OS image and connection is working fine. but I dont know how to communicate from application layer, I want to send some row string data to my connected USB device. Can anybody give me the idea about communicating with RNDIS layer over Communication device class. Thanks HimaNshu Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88877
  - 13
    - unresolved external symbols __CxxFrameHandler, _Xlen, _Xran (C++ std linking errors) I went through the trouble of figuring out a C++ linking error. It seemed like a good newsgroup post so I'm passing along the information. Problem: I kept getting these errors when linking an application that used std::basic_string<TCHAR> -------------------------------------------------------------------------------------------------------- error LNK2019: unresolved external symbol "void __cdecl std::_ Xran(void)" (?_Xran@std@@YAXXZ) referenced in function "public: int __cdecl std::basic_string<unsigned short,struct std::char_traits<unsigned short>,class std::allocator<unsigned short> >::compare(unsigne d int,unsigned int,unsigned short const *,unsigned int)const " (?compare@?$basic_string@GU?$char_trait s@G@std@@V?$allocator@G@2@@std@@QBAHIIPBGI@Z) error LNK2001: unresolved external symbol __CxxFrameHandler error LNK2019: unresolved external symbol "void __cdecl std::_ Xlen(void)" (?_Xlen@std@@YAXXZ) referenced in function "private: bool __cdecl std::basic_string<unsign ed short,struct std::char_traits<unsigned short>,class std::allocator<unsigned short> >::_Grow(unsigne d int,bool)" (?_Grow@?$basic_string@GU?$char_traits@G@std@@V?$allocator@G@2@@std@@AAA_NI_N@Z) -------------------------------------------------------------------------------------------------------- I had used this small test program in other projects so I was confused as to why the program wouldn't link now The .lib needed for std C++ is coredll.lib which was correctly linked in the SOURCES file as TARGETLIBS=$(_COMMONSDKROOT)\lib\$(_CPUINDPATH)\coredll.lib Solution: The Catalog Item "C++ Runtime Support for Exception Handling and Runtime Type Information" (SYSGEN_CPP_EH_AND_RTTI) was not included in the OS Design. -J Tom Moon Qualnetics A related post is here: http://groups.google.com/group/microsoft.public.windowsce.platbuilder/browse_frm/thread/92f5434888983835/9075e78435632041?lnk=gst&q=_XRan+link&rnum=1#9075e78435632041 Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88875
  - 14
    - WebServer using SSL Hi, What component I need to add to my platform to allow SSL/TLS connection to my web server, telnet server, etc.? Please notice that my device is a headless device connected on the network. I tried to use the ENROLL.EXE sample but it seams that it can't be used on a headless device correctly, am I right? Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88869
  - 15
    - SMSC end of my rope Hi All, I have been stuggling off and on for better than a month with the SMSC LAN91C111 and Windows CE 4.1 running on an XSCALE board. The design was based on the MAINSTONE, and I have had lots and lots of problems. A number of them were simply inexperience on my part. Others were bugs in the MAINSTONE reference and the driver code from SMSC. I would never have made it this far without the help I received from this news group. Everyone here is great. I wish I could say the same for the support I have received from SMSC. Even with all the work I have done, I am still very disappointed with my ENET implementation. Currently, I am using the ENET driver version 2.0 in combination with the LAN91C111 10/100 ENET part on a PXA270 XSCALE based board. At first glance, when Windows CE 4.1 boots, the Ethernet appears to be working. I get a DHCP address, I can ping the address, and the responses are consistently in the 2ms range. I can also browse the internet successfully. I have an application that periodically sends small TCP packets to a server for processing, and this works too. Using simple PING sessions, I have successfully communicated with the unit over a 48 hour period. However, everything I have described up until this point is very "light" traffic. If I try to FTP files, use MS ActiveSync over ENET, or run an Ethernet debugger, very quickly I begin to see RX Overruns. After a few more seconds and some mini-port resets, my Ethernet connection is locked up and I must disconnect and reconnect the media to restore the connection. My debug or FTP or whatever session is ruined until I reboot the platform, but I can restore the ability to respond to PINGs. I see a number of these same kind of reports scattered on the web, specific to the SMSC part/driver paired up with the XSCALE processor. The reported cause is "missed" interrupts, stemming from the part being level sensitive, and the PXA270 being an edge triggered device. The way software flows is like this: 1) The OEMInterrupt handler will get called in the kernel. This function is responsible for returning the SYSINTR value that in turn triggers the Interrupt handler in the SMSC driver. At this time, additional interrupts from this GPIO source are disabled. 2) Once triggered, the SMSC Interrupt Handler essentially "polls" the chip and tries very hard not to exit until it has serviced all requests. Once the chip reports no more interrupts, OEMInterruptDone gets called down in the kernel. 3) In OEMInterruptDone, the GPIO which monitors the SMSC interrupt gets re-enabled. The obvious spot for an interrupt to get missed is between the time when the driver last checks the SMSC chip for interrupts, and control gets back to the kernel and OEMInterruptDone is called. What seemed like the most straight forward solution was to simply re-enable the GPIO interrupt, then do a level check before exiting. If the level indicated an interrupt, but the edge detect bit was not set, then I knew I had missed the edge, and I simply needed to return the SYSINTR value and the process would start all over again. This is the technique we used on our old SMSC part, the SMC9000 chip, and it served us well. However when the problem still persisted, I assumed this technique was not going to cut it for the new 100MB part. So I got with our hardware engineer, and we AND'ed the SMSC interrupt in our CPLD with the 50Mhz CPLD clock. The thought now was if we missed an edge so what. I reconfigured the GPIO to trip on a rising or falling edge and thought there was no way now the issue would persist. Yet it did. At that point I did some more digging through the news groups. Someone directed me to an interesting thread written by a knowledgeable source that claimed sometimes the NDIS layer did not always call EnableInterruptHandler using the call back address provided by the NDIS_MINIPORT_CHARACTERISTICS structure. The suggested fix was to NULL out this parm in the structure, and manually invoke this function at the end of the HandleInterruptHandler function. I did this but did not see any improvement. Is there anyone out there who can tell me they use this part with the XSCALE and have satisfactory results? I'm not looking for throughput, just stability. I am beginning to doubt whether this is possible without a serious rewrite of the SMSC supplied driver. If anyone could share any experiences on this subject, even if it is to suggest another ENET part altogether, I'd appreciate any and all feedback. Thanks in advance to everyone who takes the time to respond! Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88866
  - 16
    - Bluetooth / Serial how it works? Hi all I have a bluetooth device connected to my ADS's UART port. I just know how to make it work but don't understand why and how it work. My step is as follow: 1. connect the Bluetooth component to the UART port 2. run the program BTCP 3. go to control panel, scan device~ I don't understand what BTCP actually do? Why if i skip that step, then wince will consider no bluetooth device connected? Also how those BT component communicate with my bluetooth chip? Via serial manager? Thanks very much for explain. Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88863
  - 17
    - Preferred method to get interrupts Hello All, What is the preferred method to get interrupts in WM 5.0? From what I have seen, there are two possibilities. 1. Use CardRequestIRQ and CardRequestConfiguration to register the ISR. 2. Register an event using InterruptInitialize, then start an IST which blocks on the event using WaitForSingleObject? What are the differences between the two? Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88862
  - 18
    - Optimizing a USB modem driver Hello all, I am working on a USB modem driver for a windows mobile 5.0 platform. I am looking for hints to improve the throughput. One of the suggestions in the documentation for IssueBulkTransfer is :- "To maximize speed, USB host client drivers should fill pBuffer and use asynchronous mode" . I assume it was meant to be "client drivers should fill PhysAddr"? Any other suggestions to improve the throughput will be appreciated. Thanks Sumit Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88861
  - 19
    - [OT] Using VS 2005 for CE application Development If this is not the correct group to be asking this question I would appreciate a pointer to the correct one. I am looking to purchasing Visual Studio 2005. At this time I use eVC for application development on a custom platform for a client. Our future direction for this product requires adding some additional features that the client would like developed in VS 2005. My question is: does the Standard version of VS 2005 support development of applications using the .NET compact framework for custom platforms? With eVC we use the SDK generated with PB, I am asuming VS 2005 can also use this SDK. I would like to use the standard version since it is quite a bit less expensive; however it is not clear from any details I can find whether it supports this development. We will be using CE 5 for the future development too. Many thanks, Sid. Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88859
  - 20
    - !if 0 I have the following code in one of the sources file, what on earth does the !if 0 refer to, especially the one surrounding $(_COMMONOAKROOT)\lib\$(_CPUINDPATH)\xsc1_ser16550.lib. I can't for the life in me remember. !if 0 Copyright (c) Microsoft Corporation. All rights reserved. !endif !if 0 Use of this source code is subject to the terms of the Microsoft end-user license agreement (EULA) under which you licensed this SOFTWARE PRODUCT. If you did not accept the terms of the EULA, you are not authorized to use this source code. For a copy of the EULA, please see the LICENSE.RTF on your install media. !endif SOURCELIBS= \ $(_COMMONOAKROOT)\lib\$(_CPUINDPATH)\com_mdd2.lib \ $(_COMMONOAKROOT)\lib\$(_CPUINDPATH)\ser_card2.lib \ $(_COMMONOAKROOT)\lib\$(_CPUINDPATH)\ser16550.lib \ !if 0 $(_COMMONOAKROOT)\lib\$(_CPUINDPATH)\xsc1_ser16550.lib !else $(_TARGETPLATROOT)\lib\$(_CPUINDPATH)\xsc1_ser16550.lib !endif Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88850
  - 21
    - [Q] Serial Port - Overrun error Hello everyone. I had an error during serial communication. My Device spec. is below.(We are developing a PDA platform) CPU : PXA270 OS : Windows CE 5.0 BSP : Mainstone III Test program environment: PC : data sender Target Device(Our platform) : data receiver Receiver Port : FFUART, STUART, and additional Dual UART(We added a DUART chip(have rx/tx/rts/cts/16 bytes fifo, no modem control lines)) baud rate : 9600, 38400, 57600, 115200 Flow control : None or Hardware(RTS/CTS) When I send packet data(1KB) from PC to Target Device continuosly, SERIAL_LSR_OE is occurred in "BYTE CPdd16550::GetLineStatus()" in pdd16550.cpp At any baud rate, any serial port, Overrun is occurred. Where should I look up? What should I test? Please, help me!!! Thanks. Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88848
  - 22
    - How to resolve "Failed to co-create service host!" error in PB Hi, When I try to connect to the Emulator via "Target | Attach Device" menu in PB 5.0, it says: (CoreCon) 17:45:09 08/22/2006: Failed to co-create service host! (CoreCon) 17:45:09 08/22/2006: Transport service failed to connect (CoreCon) 17:45:09 08/22/2006 : Warning: One or more services failed to connect. Make sure that the service is properly configured. What can I do? Thanks in advance. Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88847
  - 23
    - Problem while Installing the WinCE 5.0 driver on CEPC using .cab files I am using WinCE 5.0 and I have one system CEPC that has pentium II. I have created some modem device driver on windows ce 5.0. I want to create some installation utility to install the wince driver on CEPC using .cab files. So first i created .inf files as mentioned in the help documentation of WinCE platform builder 5.0 and then i am trying to create .cab file using this inf file. While creating cab file i am getting the error "Error: Section [DestinationDirs] has no data". Please suggest me regarding the reason of getting this error?? Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88846
  - 24
    - what does the function "BthAGNetworkAnswerCall" do? when the event that the peer hand-free device's button is pushed appears,this function is called.But i don't really what it does for i can not get source code of this function.i need your help. thanks in advance -- dean chen Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88845
  - 25
    - Bluetooth components Hi I am having problem to run my bluetooth devices via com1. I have success run my BT device using H4. But when I change to BCSP, then devices cannot run at all. Want to ask. 1. What components I need for CSP Bluetooth chips? Is it Bluetooth Stack with Integrated CSR Chipset Driver only or Bluetooth Stack with Integrated CSR Chipset Driver + Bluetooth Stack with Univeral Loadable Driver? 2. Do I need to change or add any registry? I have make sure the baud rate and com port same as I set in my devices Thanks very much for any help~~~ h Tag: Can I use PB to build the btscosnd driver and download it onto my SPV C600 Tag: 88844

Hi,

I'm trying to build the btscosnd driver, I built it using VS2005, but
can seem
to get the SPV to load it at boot-up. I think this is the case because
although I put the dll in \windows directory and appropriate entries in
the
registry HKLM\Drivers\Builtin\BTScoSnd etc I get no entry in
HKLM\Drivers\Active to say that the driver has been loaded.

I'd like to use PB to this work, but I wasn't certain I could use PB if
I was not downloading the complete kernel to the device (in this case
my SPV)

Any advice ?

Cheers

Paul Grant

Top