Wince 4.2 to 5.0 Migration issue

Tutorials Win: Microsoft Windows Forum

- Previous
  - 1
    - Hive based registry hangs in retail build Hi, have PXA255 platform derived from Lubbock. Using WInCE 5.0. I have setup my hive registry to be on NOR Flash. Everything works fine in a debug build, hives are mounted on flash and booting time is aorund 20 seconds. With a release build its taking long time to boot around 5 minutes. Any help is appreciated, thanks Anand Tag: Wince 4.2 to 5.0 Migration issue Tag: 84956
  - 2
    - Hard drive does not init Hi, I'm trying to add a HDD to a CEPC image. I've followed all the step-by-step instructions and scoured the documentation for anything I might have missed, to no avail. My bios detects the hard drive correctly, but in the kernel debugger, when CE tries to initialize the drive, it complains that "device busy" and then "failed to initialize device." My working hypothesis is that CE can't deal with the ide controller, which is an intel 82801DB (deviceId 0x24CB). I haven't been able to find CE drivers for the Intel chipset on our SBC. Intel cryptically says "PIO" on their driver matrix for this chipset, but changing the transfer mode hasn't made any difference. If anyone has some insight into this problem, I would greatly appreciate the help. Here's the debug log: >>> Loading module atapi.dll at address 0x03CE0000-0x03D06000 (RW data at 0x01FD7000-0x01FD7608) ATAPI DLL_PROCESS_ATTACH ATAPI:PCIConfig!DeviceConfig+(0) ATAPI:PCIConfig!ConfigRsrc+(Bus 0, Device 31, Function 1) ATAPI:PCIConfig!ConfigRsrc: BAR(0/31/1): Offset 0x10, Type I/O, Size 0x8 ATAPI:PCIConfig!ConfigRsrc: BAR(0/31/1): Offset 0x14, Type I/O, Size 0x4 ATAPI:PCIConfig!ConfigRsrc: BAR(0/31/1): Offset 0x18, Type I/O, Size 0x8 ATAPI:PCIConfig!ConfigRsrc: BAR(0/31/1): Offset 0x1c, Type I/O, Size 0x4 ATAPI:PCIConfig!ConfigRsrc: BAR(0/31/1): Offset 0x20, Type I/O, Size 0x10 ATAPI:PCIConfig!ConfigRsrc: BAR(0/31/1): Offset 0x24, Type Memory, Size 0x400 ATAPI:PCIConfig!ConfigRsrc- Warning: No Match template is found for following PCI Device ------------------------------------------------------------------------------- Bus/Device/Function = 0/31/3, Unknown Device Type VendorID = 0x8086, DeviceID = 0x24C3, Command = 0x0001, Status = 0x0280 RevisionID = 0x02, ProgIf = 0x00, SubClass = 0x05, BaseClass = 0x0C CacheLineSize = 0x00, LatencyTimer = 0x00, HeaderType = 0x00, BIST = 0x00 BaseAddresses: 0x00000000 0x00000000 0x00000000 0x00000000 0x00000501 0x00000000 CIS = 0x00000000, SubVendorID = 0x8086, SubSystemID = 0x24C2 ROMBaseAddress = 0x00000000 InterruptLine = 0x0A, InterruptPin = 0x02, MinGrant = 0x00, MaxLatency = 0x00 ------------------------------------------------------------------------------- PCIBUS!PCICfgCheckBARs: WARNING: No matching registry key was found for placed device 0/31/3. PCIBUS!PCICfgCheckBARs: Problems can result if the device is being used while configuring PCIbus. PCIBUS!PCICfgAllocMemSpace: Failed to place Device resource: Bus 0, Device 0, Function 0 ATAPI:PCIConfig!DeviceConfig+(1) PCIBUS!PCICfgAllocIoSpace: Failed to place Bridge resource: Bus 0, Device 30, Function 0 PCIBUS!PCICfgAllocIoSpace: Failed to place Device resource: Bus 0, Device 31, Function 3 ATAPI:PCIConfig!DeviceConfig+(1) ATAPI:PCIConfig!DeviceConfig+(1) ATAPI:PCIConfig!DeviceConfig+(1) ATAPI:PCIConfig!DeviceConfig+(1) ATAPI:PCIConfig!DeviceConfig+(1) ATAPI DLL_PROCESS_DETACH <<< Unloading module atapi.dll at address 0x03CE0000-0x03D06000 (RW data at 0x01FD7000-0x01FD7608) EPC_X86_DEBUG\ATAPI.DLL' >>> Loading module atapi.dll at address 0x03CE0000-0x03D06000 (RW data at 0x01FD7000-0x01FD7608) C_X86_DEBUG\ATAPI.DLL' ATAPI DLL_PROCESS_ATTACH ATAPI:PCIConfig!DeviceConfig+(2) ATAPI:PCIConfig!ConfigSize+(Bus 0, Device 31, Function 1) ATAPI:PCIConfig!ConfigSize- ATAPI DLL_PROCESS_DETACH <<< Unloading module atapi.dll at address 0x03CE0000-0x03D06000 (RW data at 0x01FD7000-0x01FD7608) EPC_X86_DEBUG\ATAPI.DLL' >>> Loading module atapi.dll at address 0x03CE0000-0x03D06000 (RW data at 0x01FD7000-0x01FD7608) C_X86_DEBUG\ATAPI.DLL' ATAPI DLL_PROCESS_ATTACH ATAPI:PCIConfig!DeviceConfig+(3) ATAPI DLL_PROCESS_DETACH <<< Unloading module atapi.dll at address 0x03CE0000-0x03D06000 (RW data at 0x01FD7000-0x01FD7608) EPC_X86_DEBUG\ATAPI.DLL' DEVICE!RegReadActivationValues RegQueryValueEx(Drivers\BuiltIn\PCI\Instance\ALI14531\BusPrefix) returned 2 >>> Loading module atapi.dll at address 0x03CE0000-0x03D06000 (RW data at 0x01FD7000-0x01FD7608) C_X86_DEBUG\ATAPI.DLL' ATAPI DLL_PROCESS_ATTACH Atapi!DumpRegKey> Drivers\Active\4294967293 Hnd = 00051600 Name = IDE1: Key = Drivers\BuiltIn\PCI\Instance\ALI14531 BusParent = 0004C540 InterfaceType = 00000005 BusName = PCI_0_31_1 Atapi!DumpRegKey> Drivers\BuiltIn\PCI\Instance\ALI14531 IoLen : 8 4 8 4 10 IoBase : a030 a040 a038 a044 a020 MemLen = 00000400 MemBase = 80000000 FunctionNumber = 00000001 DeviceNumber = 0000001F BusNumber = 00000000 InterfaceType = 00000005 SubSystemID = 000024C2 SubVendorID = 00008086 RevisionID = 00000002 DeviceID = 000024CB VendorID = 00008086 ProgIF = 0000008A RegisterStride = 00000001 StatusPollCyclePause = 00000005 StatusPollsPerCycle = 00000020 StatusPollCycles = 00000100 SoftResetTimeout = 00000003 DMAAlignment = 00000004 SysIntr = 00000000 Irq = 0000000E Legacy = 00000001 ConfigEntry = GenericConfig SubClass = 00000001 Class = 00000001 Order = 00000002 Dll = atapi.dll Prefix = IDE IClass : {CDDC3621-3512-4b3f-BB6F-B4DD5E061795} SpawnFunction = CreatePCIHDCD InstanceIndex = 00000001 Atapi!IDE_Init> Start of IDE/ATA device enumeration Atapi!IDE_Init> Enumerated IDE/ATA device Drivers\BuiltIn\PCI\Instance\ALI14531\Device3 Atapi!IDE_Init> Enumerated IDE/ATA device Drivers\BuiltIn\PCI\Instance\ALI14531\Device2 Atapi!IDE_Init> Enumerated IDE/ATA device Drivers\BuiltIn\PCI\Instance\ALI14531\Device1 Atapi!IDE_Init> Enumerated IDE/ATA device Drivers\BuiltIn\PCI\Instance\ALI14531\Device0 Atapi!IDE_Init> End of IDE/ATA device enumeration Atapi!IDE_Init> Activating IDE/ATA device Drivers\BuiltIn\PCI\Instance\ALI14531\Device0 DEVICE!RegReadActivationValues RegQueryValueEx(Drivers\BuiltIn\PCI\Instance\ALI14531\Device0\BusPrefix) returned 2 Atapi!DumpRegKey> Drivers\Active\4294967294 Hnd = 00051EF0 Name = DSK1: Key = Drivers\BuiltIn\PCI\Instance\ALI14531\Device0 Atapi!DumpRegKey> Drivers\BuiltIn\PCI\Instance\ALI14531\Device0 Port = 00051820 TransferMode = 000000FF DeviceId = 00000000 LookAhead = 00000001 WriteCache = 00000001 DrqDataBlockSize = 00000200 DoubleBufferSize = 00010000 DMA = 00000002 InterruptDriven = 00000001 Dll = atapi.dll Prefix = DSK IClass : {A4E7EDDA-E575-4252-9D6B-4195D48BB865} Atapi!CPCIDisk::CPCIDisk> device count(1) Atapi!CDisk::ResetController> Device is busy; 3 seconds remaining Atapi!CDisk::ResetController> Device is busy; 2 seconds remaining Atapi!CDisk::ResetController> Device is busy; 1 seconds remaining Atapi!CDisk::ResetController> Timeout Atapi!CDisk::Init> Failed to initialize device Atapi!CPCIDisk::~CPCIDisk> device count(0) DEVICE!LaunchDevice: Init() failed for device 0x00051ef0 DEVICE!I_ActivateDeviceEx: couldn't activate: prefix DSK, index 1, dll atapi.dll, context 0x802d030 Atapi!IDE_Init> Activating IDE/ATA device Drivers\BuiltIn\PCI\Instance\ALI14531\Device1 DEVICE!RegReadActivationValues RegQueryValueEx(Drivers\BuiltIn\PCI\Instance\ALI14531\Device1\BusPrefix) returned 2 Atapi!DumpRegKey> Drivers\Active\00 Hnd = 00052160 Name = DSK1: Key = Drivers\BuiltIn\PCI\Instance\ALI14531\Device1 Atapi!DumpRegKey> Drivers\BuiltIn\PCI\Instance\ALI14531\Device1 Port = 00051820 TransferMode = 000000FF DeviceId = 00000001 LookAhead = 00000001 WriteCache = 00000001 DrqDataBlockSize = 00000200 DoubleBufferSize = 00010000 DMA = 00000002 InterruptDriven = 00000001 Dll = atapi.dll Prefix = DSK IClass : {A4E7EDDA-E575-4252-9D6B-4195D48BB865} Atapi!CPCIDisk::CPCIDisk> device count(1) Atapi!CDisk::IsDevicePresent> Device 1 is not present; Error register(0xff) Atapi!CDisk::InitController> Device did not respond to identify Atapi!CDisk::Init> Failed to initialize device Atapi!CPCIDisk::~CPCIDisk> device count(0) DEVICE!LaunchDevice: Init() failed for device 0x00052160 DEVICE!I_ActivateDeviceEx: couldn't activate: prefix DSK, index 1, dll atapi.dll, context 0x802d030 Atapi!IDE_Init> Activating IDE/ATA device Drivers\BuiltIn\PCI\Instance\ALI14531\Device2 DEVICE!RegReadActivationValues RegQueryValueEx(Drivers\BuiltIn\PCI\Instance\ALI14531\Device2\BusPrefix) returned 2 Atapi!DumpRegKey> Drivers\Active\01 Hnd = 000523D0 Name = DSK1: Key = Drivers\BuiltIn\PCI\Instance\ALI14531\Device2 Atapi!DumpRegKey> Drivers\BuiltIn\PCI\Instance\ALI14531\Device2 Port = 00051890 DeviceId = 00000000 TransferMode = 000000FF LookAhead = 00000001 WriteCache = 00000001 DrqDataBlockSize = 00000200 DoubleBufferSize = 00010000 DMA = 00000002 InterruptDriven = 00000001 Dll = atapi.dll Prefix = DSK IClass : {A4E7EDDA-E575-4252-9D6B-4195D48BB865} Atapi!CPCIDisk::CPCIDisk> device count(1) Atapi!CDisk::ResetController> Device is busy; 3 seconds remaining Atapi!CDisk::ResetController> Device is busy; 2 seconds remaining Atapi!CDisk::ResetController> Device is busy; 1 seconds remaining Atapi!CDisk::ResetController> Timeout Atapi!CDisk::Init> Failed to initialize device Atapi!CPCIDisk::~CPCIDisk> device count(0) DEVICE!LaunchDevice: Init() failed for device 0x000523d0 DEVICE!I_ActivateDeviceEx: couldn't activate: prefix DSK, index 1, dll atapi.dll, context 0x802d030 Atapi!IDE_Init> Activating IDE/ATA device Drivers\BuiltIn\PCI\Instance\ALI14531\Device3 DEVICE!RegReadActivationValues RegQueryValueEx(Drivers\BuiltIn\PCI\Instance\ALI14531\Device3\BusPrefix) returned 2 Atapi!DumpRegKey> Drivers\Active\02 Hnd = 00052640 Name = DSK1: Key = Drivers\BuiltIn\PCI\Instance\ALI14531\Device3 Atapi!DumpRegKey> Drivers\BuiltIn\PCI\Instance\ALI14531\Device3 Port = 00051890 DeviceId = 00000001 TransferMode = 000000FF LookAhead = 00000001 WriteCache = 00000001 DrqDataBlockSize = 00000200 DoubleBufferSize = 00010000 DMA = 00000002 InterruptDriven = 00000001 Dll = atapi.dll Prefix = DSK IClass : {A4E7EDDA-E575-4252-9D6B-4195D48BB865} Atapi!CPCIDisk::CPCIDisk> device count(1) Atapi!CDisk::IsDevicePresent> Device 1 is not present; Error register(0xff) Atapi!CDisk::InitController> Device did not respond to identify Atapi!CDisk::Init> Failed to initialize device Atapi!CPCIDisk::~CPCIDisk> device count(0) DEVICE!LaunchDevice: Init() failed for device 0x00052640 DEVICE!I_ActivateDeviceEx: couldn't activate: prefix DSK, index 1, dll atapi.dll, context 0x802d030 Tag: Wince 4.2 to 5.0 Migration issue Tag: 84948
  - 3
    - Unfilled ROM holes Does anyone have any suggestions on how to minimize the amount of space in unfilled ROM holes in an OS image build ? It seems like the packing is based on the order things are found in ce.bib which is based on where they are in the various .bib files. If you start with a bunch of 'small' files and then graduate up to the large file components, it would seem like you'll end up with a fairly different OS footprint, but there doesn't appear to be much control available or a good step to insert a home-grown tool. If I wanted to go in a shuffle the order of entries in ce.bib, where could I insert that ? The initial call is into makeimg.exe. Tag: Wince 4.2 to 5.0 Migration issue Tag: 84943
  - 4
    - Copying a file deletes file attributs Hello, today I discovered a new, real, problem. If I copy a file from on storage (IDE > Compact Flash > FAT) to another (USB > Memory Stick > FAT) the file attributs are gone. Archive is always on, Read-only is always off and Hidden is correct. I have tested this behavior with Windows CE Explorer and a simple application using the FileCopy API. Have I missed an registry key? Platform Build 5.0 x86 All QFEs until Windows CE 5.0 Update 060430_2006M04 Regards Peter Tag: Wince 4.2 to 5.0 Migration issue Tag: 84934
  - 5
    - Problem adding SIP driver Hello, When adding the 'SIP for Large Screens' in a WinCE 5 Platform Build, I get the following error during Platform Build (build.log) : coredll.def : error LNK2001: unresolved external symbol SipEnumIM coredll.def : error LNK2001: unresolved external symbol SipGetCurrentIM .... coredll.def : error LNK2001: unresolved external symbol SipStatus I checked and added Catalog Item Dependencies and found nothing wrong. Any ideas ? Thanks in advance, Joost. Tag: Wince 4.2 to 5.0 Migration issue Tag: 84931
  - 6
    - Release filesystem with passive KITL (CE5) Hi all, In my target (pxa25x, windows CE5) I have enabled passive kitl. Whenever I generate an exception to start up the debugger, the target connects to my debugger and handles the exception but right after that it gets more exceptions all relating to fsdmgr/relfsd. >From what I see in the debug output, the target control shell tries to open the \\release\\con directory and fails to do so, generating an exception. It continues to attempt to open this device and thus, continues to generate exceptions all over....this makes it impossible for me to use the kernel debugger in a decent way. I suspect that relfsd tried to mount the filesystem during bootup (I disabled the "mountasbootable" registry setting) and does not find the debug link and then fails somehow. Am I missing a configuration setting somewhere or should I not use the target control tools at all when using passive KITL? (when I disable the target control tools the debugger connects fine and does not receive any exceptions other than the one I generated to kick start the debugger). Any thoughts appreciated, Niels Brouwers Chess Tag: Wince 4.2 to 5.0 Migration issue Tag: 84926
  - 7
    - .NET CF What are all the version of .NET CF? Could you list them? .NET CF 1.0 S.P.1.. ... .NET CF 2.0 S.P.1.. Max Tag: Wince 4.2 to 5.0 Migration issue Tag: 84925
  - 8
    - Remote tools of eVC 4.0 SP4 not working with platform 4.2 Hello experts After installing SP4 for Microsoft eMbedded Visual C++ 4.0 the remote tools don't work anymore. We always get the message "Cannot find appropiate device side files associated with this tool", if we try to connect to our device. We didn't have this problem with SP3. The KB article http://support.microsoft.com/kb/873411/en-us mentions a QFE, which I would like to install, but I can't find it anywhere. Does someone know how to get the remote tools of eVC++ 4.0 SP4 working with a CE 4.2 device? Our device is a PB4.2, SH3, with all QFEs until Jan 2006 installed. TIA -- Michael Reim reim AT helmut-fischer DOT de Tag: Wince 4.2 to 5.0 Migration issue Tag: 84924
  - 9
    - How to keep mounting SD card while suspending the system? Hi there, There is a SDIO driver stack in PB 5.0. By default, the SD card will be unmounted while system is suspended, and will be mounted again after system resumes. Some operations such as copying file from/to the SD card, playing MP3 files on the SD card, will be abnormal during the dismount/mount handling. How can we change the default behaviour to let the suspend/resume be transparent to the operations? Best. Tag: Wince 4.2 to 5.0 Migration issue Tag: 84922
  - 10
    - Will DCOM still be supported in CE 6.0? Now that CE 6.0 Beta has been announced at MEDC2006, what are the plans for DCOM in Windows CE 6.0? Can I convert my current applications that use DCOM to windows CE 6.0? W. Tag: Wince 4.2 to 5.0 Migration issue Tag: 84921
  - 11
    - CEPC and host connectivity Hi all, I have a CEPC system running and my host can download the NK.bin image to the CEPC so that it boots up fine. The only problem now I am facing is, the remote tools always fail to connect to the CEPC... I had no problems with connectivity when I was using MS deviceEmulator and ActiveSync over DMA. But ActiveSync doesn't support Ethernet connectivity (correct me if I am wrong) and hence can't use ActiveSync to connect to my CEPC over ethernet. I can't use COM1 port to connect host as the only COM port of the CEPC is connected to the Radio and the host is connected through ethernet only. So the only options left for me are 1. KITL bootstrap server with KITL transport. - this fails. Do I need to explicitly add something to the OS image/registry to enable the KITL bootstrap server? Any pointers? 2. CESH server for WINCE with TCP/IP transport - this too fails. saying the service is not started. 3. Manual server with TCP/IP - this says copy 3/4 files to the target device and run a cemgr.exe with some arguments. My question is how do I copy those files to the target of the connection is not available in the first place? Is it possible to add those files to the NK.bin when I am building it and then run the commanline as the documentaion says? If so, shall I run it from PB->Target->Run Programs? any help on these will be highly appreciated. thanks, soum Tag: Wince 4.2 to 5.0 Migration issue Tag: 84919
  - 12
    - Logical Address To Physical Address Hi there, I'm starting developing a very simple Windows CE 5.0 driver in the Platform Builder 5.0. My first question is: how can i get a physical address from a logical address (passed to the driver as pointer to a buffer)? Where can I get some more exhaustive documentation about these kind of task? Thanks a lot in advance! PS: Excuse me for my maybe-trivial questions, I'm quite new in driver programming. Tag: Wince 4.2 to 5.0 Migration issue Tag: 84918
  - 13
    - Real SD card size If one SD card vendor says its SD cards are 512 Mb, I'm not sure their size is 512 Mb.. However, I'd like to know what's the max size range and from what features (physical and software) it depends on. Could you help me? Max P.S. A-DATA says "For our 512MB SD card, the real capacity is about 476MB to 498MB" Tag: Wince 4.2 to 5.0 Migration issue Tag: 84915
  - 14
    - Where can I get Russian Language Resources? I set default language of my platform to Russian, but Explorer's Menu is displayed in English.... Because Windows CE 5.0 does not include Russian language Resouces...Is Right? So, It's too hard to find companies supporting or selling Russian language resouces.. is here anyone who knows the company? Tag: Wince 4.2 to 5.0 Migration issue Tag: 84913
  - 15
    - Is CE 6.0 stable? Is the CE 6.0 beta stable? Oup app is to release in a year and I'd like to dev using CE6 and CF 20 if possible. THX Tag: Wince 4.2 to 5.0 Migration issue Tag: 84903
  - 16
    - How to let my device connect to the host Hi All, I can use the emulator to connect the host like this: '\\jmdv\' and the explorer of emulator show the shared florders.And I can't use the IP '\\192.168.0.1\' to access the host in emulator. However, When I use the device to access the host,both of '\\jmdv\' and '\\192.168.0.1\' are invaild.But the device can show the internet web page. Why? RG Peter Tag: Wince 4.2 to 5.0 Migration issue Tag: 84900
  - 17
    - Bug in OHCI2 driver for Windows CE 5.0? Hi all, I'm in a middle of porting USB device-driver from Windows NT/2k/XP... to Windows CE, and I have few questions: Did anyone knows why I can't transfer zero byte vendor-transfer? (It's failed immediatly) That was the easy question. Now for my serious one, we have couple of hardwares and firmware versions which the driver should work upon: 1. A low-speed device (Contains couple of firmware versions) 2. A full-speed device (Contains couple of firmware versions) The low-speed device and the first firmware version of the full-speed device are working ok (Except for the 0 byte transfer which we had to put a dummy byte instead... We have try virtually every possibility for argument cominations.) However we got some problems in the second full-speed device and a special version of the low-speed device. After poking in the hardware and in the driver code, we have found that a time-out occured for a control transfer (Vendor transfer). The timout was caused due to the following: - For all hangs versions (both full-speed and high-speed), the firmware version sends short-packets. The USB transaction is closed before all accpeted bytes are transfered. Since we have used the USB_SHORT_TRANSFER_OK flag, we assumed that the OHCI device stack will act like the 2k WDM stack. - The tranasction is hung only if the number of recive bytes are lower then the USB transaction length. - Sometimes the previous rule is not completly applied (We couldn't figure out the reason for that) Anyway here are my questions: 1. Did anyone encounter these bugs before? 2. If so, do you know about a standard solution for it (QFE maybe, we installed the latest)? Thanks for advance, Elad. Tag: Wince 4.2 to 5.0 Migration issue Tag: 84896
  - 18
    - Automatic list generation of the components included in the image Hi, I want tocreate an html/list of the components added to any image, like = = the shown here http://www.arcom.com/products/icp/dev_kits/windows_ce_5/Applications_and= _Services_Develo.htm Is there a way to generate it automattically? -- = Javier Grijalba www.positivesystems.com Touch Panel - PC Systems Tag: Wince 4.2 to 5.0 Migration issue Tag: 84894
  - 19
    - Change the Display Resolution hi, I used PB 4.2 to build a Windows CE System for Samsung 2410 board. The default display resolution is 640*480. Then I wanted to change it to 800*600. I modified common.reg file: [HKEY_LOCAL_MACHINE\Drivers\Display\MQ200] "Rotate"=dword:0 "PPSupport"=dword:0 "PPSupportEnable"=dword:0 ;; 640x480x16 ; "CxScreen"=dword:280 //originally ; "CyScreen"=dword:1E0 //originally "CxScreen"=dword:320 "CyScreen"=dword:258 "BPP"=dword:16 "Freq"=dword:3C But the result is strange. Only about 4/5 of the top-left of the screen shows the gwe. 1/5 on the right is black and 1/5 on the botton is in a mess... Is there any other thing I haven't considered about? Please give me some hints. Thanks in advance! Tag: Wince 4.2 to 5.0 Migration issue Tag: 84892
  - 20
    - ActiveSync USB "Connection Not Valid" after resume Has any one encountered the same problem before? Any help will be appreciated! OS: Windows Mobile 5 (AKU 2.1) Platform: Mainstone II Description: After turn off the GSM module, suspend the devce, then resume, it will show "Unable to open the connection "USB default", the connection is no longer valid or does not exist...." . It seems there is a notification for USB connected for activesync. But in fact, we have no usb cable plugged in. Tag: Wince 4.2 to 5.0 Migration issue Tag: 84887
  - 21
    - Using WLAN card (D-link DCF-660W) in WinCE5.0 We are working on the Intersil Prism2 wlan Driver in WinCE 5.0 AMD DB1200 Platform. And using D-link Air DCF-660W WLAN card. I load the Intersil Prism2 driver - ISLP2NDS.dll for the WLAN card successfully. The LED of the card begins to blink. But ISLP21 shows the IP Information: Internet Protocol (TCP/IP): Address type: DHCP IP Address : 0.0.0.0 Subnet Mask: 0.0.0.0 The physical address is right. The card can't connect to the AP. Then I configure a static IP in the control panel for the ISLP21, but It reports the new ethernet configuration: Internet Protocol (TCP/IP): Address type: static IP Address ........ : 0.0.0.0 Subnet Mask ....... : 0.0.0.0 I checked the registry for the card, it shows as follows: [HKEY_LOCAL_MACHINE\Drivers\PCMCIA\D-Link-DCF-660W-422B] "Dll"="ndis.dll" "Prefix"="NDS" "Miniport"="ISLP2" [HKEY_LOCAL_MACHINE\Comm\ISLP2] "Displayname"="Intersil 802.11 Wireless LAN PC Card" "Group"="NDIS" "Imagepath"="ISLP2NDS.dll" [[HKEY_LOCAL_MACHINE\Comm\ISLP2\Linkage] "Route"="ISLP21" [HKEY_LOCAL_MACHINE\Comm\ISLP21] "ISLP2IOC"="ISL1:" "Displayname"="Intersil 802.11 Wireless LAN PC Card" "Group"="NDIS" "Imagepath"="ISLP2NDS.dll" "ISLP21OC"="ISL1:" [[HKEY_LOCAL_MACHINE\Comm\ISLP2\Parms] "NetWorkAddress"="000000000000" "PlugAndPlay"="0" "BusNumber"="0" "BusType"="8" "InterruptNumber"="3" "IoBaseAddress"="768" "LoadFirmware"="1" "PlatformID"="32797" [[HKEY_LOCAL_MACHINE\Comm\ISLP2\Parms\TCPIP] "DefaultGateway"="192.168.6.1" "WINS"="value not set" "DNS"="value not set" "subnetmask"="255.255.192.0" "IPAddress"="192.168.6.238" "EnableDHCP"="0" "AutoCgh"="1" The TCP/IP info is the same as that I set in the control panel. But it seem that it doesn't work. I try to modify the NetWorkAddress, but it's no use. Does anybody know what's the wrong? Thanks a lot. Tag: Wince 4.2 to 5.0 Migration issue Tag: 84886
  - 22
    - what's the difference between TARGETLIBS and SOURCELIBS? hi, experts: what's the difference between TARGETLIBS and SOURCELIBS? Tag: Wince 4.2 to 5.0 Migration issue Tag: 84882
  - 23
    - how can the build-tool build a dll when source file says "TARGETTY I am developping a driver for SDCard using WM5.0, I find the OS will load sdmemory.dll to drive the SDCard but in the source-file it defines like this TARGETDEFNAME=SDMemory DEFFILE=$(TARGETDEFNAME).def TARGETNAME=$(TARGETDEFNAME)_LIB TARGETTYPE=LIBRARY WINCETARGETFILE0=$(_COMMONOAKROOT)\lib\$(_CPUINDPATH)\$(DEFFILE) SOURCES = SDMemMain.cpp \ SDMemDiskIO.cpp \ SDMemCardIO.cpp \ it only make a LIB file but not a dll, so why does build-tools finnally make a sdmemory.dll? Tag: Wince 4.2 to 5.0 Migration issue Tag: 84881
  - 24
    - Cxport thread busy Hi, Is Cxport.dll only associated with network based devices or with input devices too, such as mouse, keyboard or USB? I have set NoIdleTimerReset but still there is high CPU activity. Is PS2 based mouse/keybd/USB power aware. Any suggestions would be greatly appreciated. Ansuya Tag: Wince 4.2 to 5.0 Migration issue Tag: 84880
  - 25
    - PB's emulator inside a virtual machine For the record: it can be done - I'm doing it under VMWare. Thanks to Barry Bond (appropriately enough, his title is "Architect") for the encouragement at the MEDC, even if his idea didn't pan out. -- #include <standard.disclaimer> _ Kevin D Quitt USA 91387-4454 96.37% of all statistics are made up Tag: Wince 4.2 to 5.0 Migration issue Tag: 84879
- Next
  - 1
    - remove unwanted project I added some projects to my platform and want to remove them. I right click on the project, but the "remove" menu item is disabled. Tapping on delete button also doesn't work. I searched the form and found a thread about DIRS related to this issue. But I haven't found any DIRS that have my projects in it. Any suggestion on this? Thanks! Richard Tag: Wince 4.2 to 5.0 Migration issue Tag: 84878
  - 2
    - repllog.exe and rnaapp.exe Hello, I have a problem of the rnaapp.exe is excecuted everytime i retun from suspend mode. It than shows the message box of "connecting to host" even if no USb cable is attached. It would like to eliminate it. Can someone please explain me what is the sequence in the system which initiates the load of repllog.exe, which than loads rnaapp.exe. Please, any help would be appreciated. Oren. Tag: Wince 4.2 to 5.0 Migration issue Tag: 84876
  - 3
    - USB device not recognized on power-up (CE-5.0) If either a USB mouse, or USB touchscreen, (drivers included into OS image), is connected to the USB-2.0 port upon power-up they aren't initialized. I have to disconnect and reconnect them then they're recognized and work However, if a standard memory stick is plugged in upon power-up it is recognized. Any ideas what could be wrong, or how to correct this? Thanks Tag: Wince 4.2 to 5.0 Migration issue Tag: 84863
  - 4
    - Compile SD_API_SUCCESS function with error. Hi all, I use SD_API_SUCCESS in my function like this : " SD_API_STATUS My_function (para,.....) { SD_API_STATUS RequestStatus; ...... ...... if (!SD_API_SUCCESS(RequestStatus)){ return RequestStatus; } } " When I build my driver, system report : error C2220: warning treated as error - no 'object' file generated : [01:0000000036:WARNN ] d:\wince500\public\common\oak\drivers\sds\xxxx.cpp( warning C4715: 'My_function': not all control paths return a value I also found that if I comment the SD_API_SUCCESS function and let My_function return RequestStatus directly, like this : " SD_API_STATUS My_function (para,.....) { SD_API_STATUS RequestStatus; ...... ...... return RequestStatus; } " then, it can be build successfully. Do you know what's the matter in My_function ? Thanks for your help. Tag: Wince 4.2 to 5.0 Migration issue Tag: 84861
  - 5
    - Why are SYSGEN vars not set? Hello experts I'm using PB5.0 and wonder whether this is a bug or desired behaviour: If I create a new custom platform based on my BSP and add some standard components e.g. "Standard Shell" to the platform, the PB IDE automatically adds e.g. "Minimal GDI Configuration" to my platform. I think this is a very useful feature. But if I call "Open Release Directory" and do a set command, I see that SYSGEN_MINGDI isn't set. Is this ok? SYSGEN_MINGDI does only get set, if I add "Minimal GDI Configuration" directly to my platform. Why is there a difference? Is this a bug? -- Michael Reim reim AT helmut-fischer DOT de Tag: Wince 4.2 to 5.0 Migration issue Tag: 84859
  - 6
    - 80X flash memory with winCE well guys can any 1 tell me, whether the flash memory having 80x data transfer rate will work with windows CE. i m using PCM 6892 card. and since years i have been using 45X Flash memory, but when i inserted 80X flash, it shows "invalid system disk". i also checked that, if i load the same flash with linux image, it works fine with the same board. so now can any 1 tell me whether 80X is supported with winCE5.0 ? thanx in advance Tag: Wince 4.2 to 5.0 Migration issue Tag: 84858
  - 7
    - Problems with corrupted hv-files generated from regcomp during makeimg Hello together, we have serious problems with corrupted hv-files generated from regcomp during makeimg. For building our Windows CE 4.2 image we call cepb from a batch file during our automatic build process. For a couple of builds (about 30%) the resulting nk.bin does not boot correctly on the target device (the filesystem does not start up correctly and the device hangs). The difference between a "good" and a "corrupt" image is only within the .hv-file within the flat release directory (boot.hv, default.hv and user.hv). These are generated from regcomp.exe during makeimg from the reginit.ini file. The difference of the binary hv-files is not only in the beginning part of the file (where there seems to be some random information (mostly the environment variables from the build machine), which are used for padding the files) but also in the back of the file, where the essential information seems to be. We have this difference even if we call regcomp.exe in the flat release directory ("regcomp reginit.ini .") as opposed to calling makimg (from the same build command line). Anyone ever had similar problems? Any idea on how to avoid these problems? In the meantime we have changed the registry settings a little bit, so that we have a different reginit.ini as input. The first tries worked, but who knows if the problem appears again. We can provide our reginit.ini and even the whole flat release directory to Microsoft for further investigation. Regards, Thomas Hensler BTW: We use PB 4.2 with the QFEs installed (which once patched regcomp.exe already). Tag: Wince 4.2 to 5.0 Migration issue Tag: 84857
  - 8
    - How to cancel/abort IObex::BindToDevice or BthAuthenticate? We are developing a Bluetooth device with MS Window CE 5.0 Bluetooth stack and are now seing a huge problem. We have found that the IObex::BindToDevice method and the BthAuthenticate seem to be blocking calls until the peer device sends an accept or reject. Yet we have not found anyway to cancel/abort such these calls or configure any timeout values for these. Does anyone know if it is possible and if so, how? If it is not possible, how is this API suppose to work properly? Thanks, Tag: Wince 4.2 to 5.0 Migration issue Tag: 84856
  - 9
    - Halt phenomenon after OEMInit() in AU1200 I am using AMD Alchemy AU1200(MIPS) processor. After executing OEMInit(), no more debug message, just halted. The debug message as follows. DEBUG MESSAGE -------------------------------------------------------------------------------- KitlTransport requested active mode. (PRId 04030201) @ 396MHZ Booting Windows CE version 5.00 for (MIPS32) MIPS16 Instructions NOT Supported &pTOC = 8110109c, pTOC = 829f1444, pTOC->ulRamFree = 82a64000, MemForPT = 00000000 Old or invalid version stamp in kernel structures - starting clean! Configuring: Primary pages: 21909, Secondary pages: 0, Filesystem pages = 10954 Booting kernel with clean memory configuration: Memory Sections: [0] : start: 82a65000, extension: 00006000, length: 05595000 Windows CE KernelInit Updated eptr->e32_vsize to = 000b1000 Scheduling the first thread. <END> ----------------------------------------------------------------------------------- Thanks in advance. Tag: Wince 4.2 to 5.0 Migration issue Tag: 84854
  - 10
    - struct ROMHDR and pTOC When I debug bootloader I was so much confused by the struct ROMHDR and the pointer pTOC. would someone please tell me who will change pTOC and where pTOC is made point. I didn't see pToc got changed explictlly. the most important is I find the information about struct ROMHDR in MSDN is too much simply to get understaood, would someone please explain every single member in that struct in detail for me? thanks so much! Tag: Wince 4.2 to 5.0 Migration issue Tag: 84853
  - 11
    - FAT Cache Pre-Warming Hello, how often is the pre-warming function of the FATFS cache triggered? Once during boot or repeatedly during runtime? Regards Peter Tag: Wince 4.2 to 5.0 Migration issue Tag: 84852
  - 12
    - Difference between Data cache and FAT cache Hello, as I have seen there are now two registry keys to configure the cache oft the FATFS (DataCacheSize, FatCacheSize). Can somebody explain the difference between Data cache and FAT cache? Regards Peter Tag: Wince 4.2 to 5.0 Migration issue Tag: 84851
  - 13
    - where have the thai language lib use for pb4.2! i use the wince50 lib of thai but can display all of them! where have the thai language lib use for pb4.2! i use the wince50 lib of thai but can display all of them! Tag: Wince 4.2 to 5.0 Migration issue Tag: 84835
  - 14
    - waking threads Hi, Why do mouse, keyboard keep on giving WaitForSingleObject every few seconds even though their dwTimeout is INFINITE... I have checked via remote kernel tracker and I see every few second either USB or some other thread unblocks and Waits for object and again blocks. Is there a way to increase this wait (it is infinite?) and there is no user input, no pressing of mouse, nothing. Is it related with idle timer settings in reg files. But then how can the system is go into idle mode when the threads keep on waking... Thanks, Ansuya Tag: Wince 4.2 to 5.0 Migration issue Tag: 84833
  - 15
    - genblt library Does anyone understand what the genblt library does in CE 5.0 ? It is linked into GPE, but doesn't appear to be activated unless registry key HKLM\Drivers\Display\GPE UseGenBlt is set. Doesn't look like anyone does that as far as the supplied drivers. Don't see anything in the help either. Tag: Wince 4.2 to 5.0 Migration issue Tag: 84832
  - 16
    - Scandisk in CE.Net 4.2 I am working with WinCE 4.2 and am attempting to use the ScanVolumeEx api to perform a periodic scan of the internal CF drive on the embedded device. When testing with a known good CF, the scan returns with no problems found. When testing with a known corrupt CF (fails chkdsk on PC). (Note: CF is FAT16) I have experienced two different issues. 1) I get "Datatype Misalignment" exception during 2nd call to HeapAlloc in GetFreeDirEntry(..) function in scandisk.cpp. (2nd call @ end of dir entry) (Note: after numerous attempts at debugging, hundreds of FILE*.CHK files were created on the root drive. At some point I began getting too many files in root and GetFreeDirEntry(..) faulted prior to calling the HeapAlloc() and exceptions stopped.) 2) With a known bad CF, scandisk does not detect failures that chkdsk detects and returns with No problems found. Does CE 5.0 have new and improved scandisk capabilty? Are there fixes for 4.2? Are there other utilities available? Any ideas? Thanks -- JMarti Tag: Wince 4.2 to 5.0 Migration issue Tag: 84826
  - 17
    - Slow Build Platform Under XP servicePack 2 Hi, I work on a fast (for me) PC (pentium 4 3.60 GHz with A 10000rpm SATA disk & 1Giga memory) The installed OS was WindowsXP servicePack 1. I build my platform CEPC projects very fast! about 5 minutes! I was very happy! Yesterday I Install ServicePack 2 and my build time slow down to 00:07:30 minutes (???!!!). I try to shutdown Firewall, Security control and so on. But nothing works(sigh!!) I disinstall ServicePack 2 and my build time return to about 5 minutes! May anyone help me Thank Ruggero Bandera Tag: Wince 4.2 to 5.0 Migration issue Tag: 84822
  - 18
    - Debug build error in Shell.exe --____OSGGVNVQDWWTHZGAXUFB____ Content-Type: text/plain; charset=iso-8859-1 Content-Transfer-Encoding: quoted-printable Hi, I'm using WinCE 5.0. My release build works fine. But debug build hangs = while loading shell.exe. The debug messages are as follows: Windows CE Kernel for ARM (Thumb Enabled) Built on Jun 24 2004 at 18:21:58 ProcessorType=3D02d0 Revision=3D6 sp_abt=3Dffff5000 sp_irq=3Dffff2800 sp_undef=3Dffffc800 OEMAddressTable = =3D 800b9d44 OEMInit ++ OEMInit -- Booting Windows CE version 5.00 for (ARM) &pTOC =3D 800c2d9c, pTOC =3D 80f6ab08, pTOC->ulRamFree =3D 80fc9000, = MemForPT =3D 00000000 Old or invalid version stamp in kernel structures - starting clean! Configuring: Primary pages: 3309, Secondary pages: 0, Filesystem pages =3D = 1654 Booting kernel with clean memory configuration: Memory Sections: [0] : start: 80fca000, extension: 00001000, length: 00ced000 Sp=3Dffffc7cc ARMInit done. Windows CE KernelInit Updated eptr->e32_vsize to =3D 000bc000 Scheduling the first thread. 0x81cb7024: KernelInit2: pCurThread=3D81cb7024 hCurThread=3D01cb7266 = hCurProc=3D01cb7002, KernelInit =3D 800df650 0x81cb7024: Detecting VFP...0x81cb7024: VFP Not Found! 0x81cb7024: Updated eptr->e32_vsize to =3D 00006000 0x81cb7024: first =3D 01f30000, last =3D 02000000, SharedDllBase =3D = 03190000 0x81ca1288: CertMod.dll not found, using old OEM Trust Model 0x81ca1288: FileSystem Starting - starting with clean file system 0x81ca1288: FS: initializing ROM/RAM file system 0x81ca1288: SC_CreateAPIHandle: pvData =3D=3D NULL 0x81ca1288: FS: Registering file system ROM, index 2, flags 0x00000031 0x81ca1288: FS: Mount complete (ROM, index 2, flags 0x00000031) 0x81ca1288: Succeeded on CheckFile 0x81ca1288: RestoreFile(0xe1c8cf02) called fDelete =3D TRUE 0x81ca1288: FS: Registering file system StoreMgr, index 3, flags 0x00000001= 0x81ca1288: FSREG: Unable to read value "NoDefaultUser" under HKEY_LOCAL_MA= CHINE\init\BootVars 0x81ca1288: FSREG: Logging in default user. 0x81ca1288: FSREG: Unable to read value "DefaultUser" under HKEY_LOCAL_MACH= INE\init\BootVars 0x81ca1288: SetCurrentUser: Logging out (nobody), logging in default 0x81ca1288: FS: Using default path "\profiles\" 0x81ca1288: BuildPath: profiles 0x81ca1288: BuildPath: profiles\default 0x81ca1288: SetCurrentUser: User hives not supported -- using same = registry for all users 0x81ca1288: FS: Using default path "Windows\" 0x81ca1288: FS: Using default path "Windows\" 0x81ca1288: FSREG: Unable to read value "DBFlags" under HKEY_LOCAL_MACHINE\= init\BootVars 0x81ca1288:=20 Initializing Database 0x81ca1288: DB:Validation: Name already exists DB_notify_events 0x81ca1288: DB:CeCreateDatabase failed 0x81ca1288: DB:Validation: Name already exists DB_notify_events 0x81ca1288: DB:CeCreateDatabase failed 0x81ca1288: ERROR: c:\macallan\private\winceos\coreos\filesys\dbase\initdb.= c line 535: 0x81ca1288: Conflict with existing database DB_notify_events = on line 385 0x81ca1288: Filesystem initialized! 0x81ca1288: FILESYS: Waiting for kernel to be ready to launch apps 0x81ca4b68: InitMUI: DISABLED (-1039860968) 0x81ca1288: FS: Creating signal event SYSTEM/DevMgrApiSetReady 0x81ca1288: FS: Creating signal event SYSTEM/PowerManagerReady 0x81ca1288: FS: Creating signal event SYSTEM/GweApiSetReady 0x81ca1288: FS: Creating signal event ReleaseFSD 0x81ca1288: FS: Creating signal event system/events/notify/APIReady 0x81ca1288: FS: Creating signal event SYSTEM/ShellAPIReady 0x81ca1288: FILESYS: Launching apps 0x81ca1288: FILESYS: Launching shell.exe 0x81c7da70: Prefetch Abort: Thread=3D81c7da70 Proc=3D80fbc5e0 'shell.exe' 0x81c7da70: AKY=3D00000005 PC=3D0002b000(shell.exe+0x0001b000) RA=3D03e21db= 4(toolhelp.dll+0x00001db4) BVA=3D0002b000 FSR=3D000004f0 0x81c7da70: Prefetch Abort: Thread=3D81c7da70 Proc=3D80fbc5e0 'shell.exe' 0x81c7da70: AKY=3D00000005 PC=3D0007f7c4(shell.exe+0x0006f7c4) RA=3D03e21fb= 0(toolhelp.dll+0x00001fb0) BVA=3D0007f7c4 FSR=3D000004f0 Any help is appreciated. Thanks Anand --____OSGGVNVQDWWTHZGAXUFB____ Content-Type: multipart/related; boundary="____FQSXIGXTRURSEYLMRUNN____" --____FQSXIGXTRURSEYLMRUNN____ Content-Type: text/html; charset=windows-1252 Content-Transfer-Encoding: quoted-printable <HTML><HEAD> <META http-equiv=3DContent-Type content=3D"text/html; charset=3Diso-8859-1"= > <META content=3D"MSHTML 6.00.2900.2802" name=3DGENERATOR></HEAD> <BODY style=3D"MARGIN: 4px 4px 1px; FONT: 10pt Tahoma"> <DIV>Hi,</DIV> <DIV>I'm using WinCE 5.0. My release build works fine. But debug build = hangs while loading shell.exe.</DIV> <DIV><BR>The debug messages are as follows:</DIV> <DIV>Windows CE Kernel for ARM (Thumb Enabled) Built on Jun 24 2004 at = 18:21:58<BR>ProcessorType=3D02d0  Revision=3D6<BR>sp_abt=3Dffff5000 = sp_irq=3Dffff2800 sp_undef=3Dffffc800 OEMAddressTable =3D 800b9d44<BR>OEMIn= it ++<BR>OEMInit --<BR>Booting Windows CE version 5.00 for (ARM)<BR>&pT= OC =3D 800c2d9c, pTOC =3D 80f6ab08, pTOC->ulRamFree =3D 80fc9000, = MemForPT =3D 00000000</DIV> <DIV> </DIV> <DIV>Old or invalid version stamp in kernel structures - starting = clean!<BR>Configuring: Primary pages: 3309, Secondary pages: 0, Filesystem = pages =3D 1654</DIV> <DIV> </DIV> <DIV>Booting kernel with clean memory configuration:<BR>Memory Sections:<BR= >[0] : start: 80fca000, extension: 00001000, length: 00ced000<BR>Sp=3Dffffc= 7cc<BR>ARMInit done.<BR>Windows CE KernelInit<BR>Updated eptr->e32_vsize= to =3D 000bc000<BR>Scheduling the first thread.<BR>0x81cb7024: KernelInit2= : pCurThread=3D81cb7024 hCurThread=3D01cb7266 hCurProc=3D01cb7002, = KernelInit =3D 800df650<BR>0x81cb7024: Detecting VFP...0x81cb7024:  = VFP Not Found!<BR>0x81cb7024: Updated eptr->e32_vsize to =3D 00006000<BR= >0x81cb7024: first =3D 01f30000, last =3D 02000000, SharedDllBase =3D = 03190000<BR>0x81ca1288: CertMod.dll not found, using old OEM Trust = Model<BR>0x81ca1288: FileSystem Starting - starting with clean file = system<BR>0x81ca1288: FS: initializing ROM/RAM file system<BR>0x81ca1288: = SC_CreateAPIHandle: pvData =3D=3D NULL<BR>0x81ca1288: FS: Registering file = system ROM, index 2, flags 0x00000031<BR>0x81ca1288: FS: Mount complete = (ROM, index 2, flags 0x00000031)<BR>0x81ca1288: Succeeded on CheckFile<BR>0= x81ca1288: RestoreFile(0xe1c8cf02) called fDelete =3D TRUE<BR>0x81ca1288: = FS: Registering file system StoreMgr, index 3, flags 0x00000001<BR>0x81ca12= 88: FSREG: Unable to read value "NoDefaultUser" under HKEY_LOCAL_MACHINE\in= it\BootVars<BR>0x81ca1288: FSREG: Logging in default user.<BR>0x81ca1288: = FSREG: Unable to read value "DefaultUser" under HKEY_LOCAL_MACHINE\init\Boo= tVars<BR>0x81ca1288: SetCurrentUser: Logging out (nobody), logging in = default<BR>0x81ca1288: FS: Using default path "\profiles\"<BR>0x81ca1288: = BuildPath: profiles<BR>0x81ca1288: BuildPath: profiles\default<BR>0x81ca128= 8: SetCurrentUser: User hives not supported -- using same registry for all = users<BR>0x81ca1288: FS: Using default path "Windows\"<BR>0x81ca1288: FS: = Using default path "Windows\"<BR>0x81ca1288: FSREG: Unable to read value = "DBFlags" under HKEY_LOCAL_MACHINE\init\BootVars<BR>0x81ca1288: <BR>Initial= izing Database<BR>0x81ca1288: DB:Validation: Name already exists DB_notify_= events<BR>0x81ca1288: DB:CeCreateDatabase failed<BR>0x81ca1288: DB:Validati= on: Name already exists DB_notify_events<BR>0x81ca1288: DB:CeCreateDatabase= failed<BR>0x81ca1288: ERROR: c:\macallan\private\winceos\coreos\filesys\db= ase\initdb.c line 535: 0x81ca1288: Conflict with existing database = DB_notify_events on line 385<BR>0x81ca1288: Filesystem initialized!<BR>0x81= ca1288: FILESYS: Waiting for kernel to be ready to launch apps<BR>0x81ca4b6= 8: InitMUI: DISABLED (-1039860968)<BR>0x81ca1288: FS: Creating signal = event SYSTEM/DevMgrApiSetReady<BR>0x81ca1288: FS: Creating signal event = SYSTEM/PowerManagerReady<BR>0x81ca1288: FS: Creating signal event = SYSTEM/GweApiSetReady<BR>0x81ca1288: FS: Creating signal event ReleaseFSD<B= R>0x81ca1288: FS: Creating signal event system/events/notify/APIReady<BR>0x= 81ca1288: FS: Creating signal event SYSTEM/ShellAPIReady<BR>0x81ca1288: = FILESYS: Launching apps<BR>0x81ca1288: FILESYS: Launching shell.exe<BR>0x81= c7da70: Prefetch Abort: Thread=3D81c7da70 Proc=3D80fbc5e0 'shell.exe'<BR>0x= 81c7da70: AKY=3D00000005 PC=3D0002b000(shell.exe+0x0001b000) RA=3D03e21db4(= toolhelp.dll+0x00001db4) BVA=3D0002b000 FSR=3D000004f0<BR>0x81c7da70: = Prefetch Abort: Thread=3D81c7da70 Proc=3D80fbc5e0 'shell.exe'<BR>0x81c7da70= : AKY=3D00000005 PC=3D0007f7c4(shell.exe+0x0006f7c4) RA=3D03e21fb0(toolhelp= .dll+0x00001fb0) BVA=3D0007f7c4 FSR=3D000004f0</DIV> <DIV> </DIV> <DIV>Any help is appreciated.</DIV> <DIV> </DIV> <DIV>Thanks</DIV> <DIV>Anand</DIV></BODY></HTML> --____FQSXIGXTRURSEYLMRUNN____-- --____OSGGVNVQDWWTHZGAXUFB____-- Tag: Wince 4.2 to 5.0 Migration issue Tag: 84815
  - 19
    - How to refer to Secure Digital Card Function Hi all, I want to refer to Secure Digital Card Driver Functions in my driver in the IDE of wince 50 with platform builder. But when I build the whole platform, system report : " sdcardlib.lib(sdmisc.obj) : error LNK2001: unresolved external symbol dpCurSettings BUILD: [01:0000003281:ERRORE] sdcardlib.lib(sddebug.obj) : error LNK2001: unresolved external symbol dpCurSettings BUILD: [01:0000003282:ERRORE] sdcardlib.lib(sdmemapi.obj) : error LNK2001: unresolved external symbol dpCurSettings BUILD: [01:0000003283:ERRORE] sdcardlib.lib(sdcardapistubs.obj) : error LNK2001: unresolved external symbol dpCurSettings BUILD: [01:0000003284:ERRORE] sdcardlib.lib(sdcardapistubs.obj) : error LNK2019: unresolved external symbol SDGetClientFunctions referenced in function SDRegisterClient " Please help me to find the error in the following things I have done. Firstly, I added this at begin of my xxxx.cpp file, such as #include <sdcardddk.h>, because I use the function of SDGetDeviceHandle(para1,para2) in my code; Secondly, I made a folder named sds in the directory of WINCE500\PUBLIC\COMMON\OAK\DRIVERS, and added a line " sds \" in the upper dir files ; Thirdly, I wrote reference paths in the sources file in sds directory like this: _ISVINCPATH=$(_WINCEROOT)\public\common\sdk\inc; _OEMINCPATH=$(_WINCEROOT)\public\common\oak\inc;$(_WINCEROOT)\public\common\sdk\inc;$(_WINCEROOT)\public\common\ddk\inc; TARGETLIBS=\ $(_PROJECTROOT)\cesysgen\sdk\lib\$(_CPUINDPATH)\coredll.lib \ $(_PROJECTROOT)\cesysgen\oak\lib\$(_CPUINDPATH)\sdcardlib.lib \ Where is the mistake ? Thanks for you help. Tag: Wince 4.2 to 5.0 Migration issue Tag: 84814
  - 20
    - Error while building USBHID driver on WinCE 5.0 Hello. I'm trying to build USBHID driver on Windows CE 5.0. when calling "sysgen" I'm getting this error: "The system cannot find the path specified." see full log below. I suspect that my mistake was creating the OS in the wrong path, or placing the HID drivers in the wrong path. I created the OS in "C:\WINCE500\PBWorkspaces\test1\WINCE500". I put the HID driver in "C:\WINCE500\PBWorkspaces\test1\WINCE500\CEPC_x86\Drivers\USB\CLASS\HID". That's where I call "sysgen" and "build -c" from. Is that the case? if not - any idea what is the problem? Thanks, Eddie. ------------------------------------------------------------- cmd log: ----------- SYSGEN_WATSON_XFER=1 Checking for uncleared variables Done checking for uncleared variables Report: SYSGEN_ATL=1 SYSGEN_AUDIO=1 SYSGEN_AUTH=1 SYSGEN_AUTH_NTLM=1 SYSGEN_AUTH_SCHANNEL=1 SYSGEN_AUTORAS=1 SYSGEN_AYGSHELL=1 SYSGEN_BATTERY=1 SYSGEN_BTH=1 SYSGEN_BTH_AG=1 SYSGEN_CERTS=1 SYSGEN_COMMCTRL=1 SYSGEN_COMMDLG=1 SYSGEN_CONNMC=1 SYSGEN_CORELOC=1 SYSGEN_CORESTRA=1 SYSGEN_CPP_EH_AND_RTTI=1 SYSGEN_CREDMAN=1 SYSGEN_CRYPTO=1 SYSGEN_CTLPNL=1 SYSGEN_CURSOR=1 SYSGEN_DEVICE=1 SYSGEN_DISPLAY=1 SYSGEN_DOTNET=1 SYSGEN_DOTNET_SUPPORT=1 SYSGEN_EAP=1 SYSGEN_ETHERNET=1 SYSGEN_ETH_80211=1 SYSGEN_FMTMSG=1 SYSGEN_FONTS_TAHOMA_1_07=1 SYSGEN_FSADVERTISE=1 SYSGEN_FSDBASE=1 SYSGEN_FSPASSWORD=1 SYSGEN_FSREPLBIT=1 SYSGEN_FULL_CRT=1 SYSGEN_GRADFILL=1 SYSGEN_HELP=1 SYSGEN_IABASE=1 SYSGEN_IE_JSCRIPT=1 SYSGEN_IMAGING=1 SYSGEN_IMAGING_BMP_DECODE=1 SYSGEN_IMAGING_GIF_DECODE=1 SYSGEN_IMAGING_JPG_DECODE=1 SYSGEN_IMAGING_PNG_DECODE=1 SYSGEN_IMM=1 SYSGEN_IPHLPAPI=1 SYSGEN_IRDA=1 SYSGEN_LDAP=1 SYSGEN_MENU_OVERLAP=1 SYSGEN_MINGDI=1 SYSGEN_MINGWES=1 SYSGEN_MININPUT=1 SYSGEN_MINWMGR=1 SYSGEN_MLANG=1 SYSGEN_MSGQUEUE=1 SYSGEN_MSIM=1 SYSGEN_MSMQ=1 SYSGEN_MSXML_DOM=1 SYSGEN_MSXML_SAX=1 SYSGEN_MSXML_XQL=1 SYSGEN_NDIS=1 SYSGEN_NDISUIO=1 SYSGEN_NKCOMPR=1 SYSGEN_NKMAPFILE=1 SYSGEN_NLED=1 SYSGEN_NOTIFY=1 SYSGEN_OBEX_CLIENT=1 SYSGEN_OBEX_SERVER=1 SYSGEN_OLE=1 SYSGEN_PM=1 SYSGEN_PPP=1 SYSGEN_PRINTING=1 SYSGEN_QVGAP=1 SYSGEN_REDIR=1 SYSGEN_SERDEV=1 SYSGEN_SERVICES=1 SYSGEN_SHELL=1 SYSGEN_SOAPTK_CLIENT=1 SYSGEN_SOFTKB=1 SYSGEN_STANDARDSHELL=1 SYSGEN_STDIO=1 SYSGEN_STDIOA=1 SYSGEN_STOREMGR=1 SYSGEN_STRSAFE=1 SYSGEN_TAPI=1 SYSGEN_TCPIP=1 SYSGEN_TCPIP6=1 SYSGEN_TIMESVC_API=1 SYSGEN_TIMESVC_DST=1 SYSGEN_TOOLHELP=1 SYSGEN_TOUCH=1 SYSGEN_URLMON=1 SYSGEN_USDK=1 SYSGEN_WATSON_CLIENT=1 SYSGEN_WATSON_CTLPNL=1 SYSGEN_WATSON_DMPGEN=1 SYSGEN_WATSON_XFER=1 SYSGEN_WEBVIEW=1 SYSGEN_WININET=1 SYSGEN_WINSOCK=1 The system cannot find the path specified. CE_MODULES=coredll nk stansdk msim commctrl commdlg shell relfsd loaddbg shellce log osaxst0 secur32 ntlmssp spnego schannel rsaenh crypt32 msasn1 credman prnpor t prnerr notify rnaapp connmc ndispwr netui wldap32 tcpstk tcpip6 ipv6hlp dhcpv6 l irdastk winsock afd ws2 ws2instl wspm nspm ssllsp rtl8139 e100bex smsc100fd dp 83815 ne2000 dhcp ethman wzcsvc wzcsapi pcx500 islp2nds wlclient wzctool eapol e ap eapchap eaptls netmui ndisuio ndis autoras ppp ircomm tapi redir netbios btsv c btd btdrt btagsvc bthuart bthamb bthsc bthcsr bthuniv wendyser wcestreambt sio 950 iphlpapi softkb gwes keybd pointer display fonts waveapi audiodrv wavesample s cxport battdrvr nleddrvr device regenum busenum pm ceddk giisr mmtimer pci pcm conv serial pccard 8042keyboard nopkeyboard csp csp_mininput fsdmgr zlib filesys toolhelp vmini rt_tests COREDLL_COMPONENTS=coremain lmem showerr thunks corecrt corestrw cryptapi tnoti fy tapilib coresip rectapi wmgr_c mgdi_c accel_c messagedialogboxthunk shcore sh ortcut shexec shmisc fileopen fileinfo shellapis dsa timezones mmwave mmsnd mmmi x battery nled devload coreimm fmtmsg corestra coresiow coresioa serdev coreloc multiui crt_cpp_eh_and_rtti full_crt crypthash rsa32 NK_COMPONENTS= nkcompr nkmapfile FILESYS_COMPONENTS=fsheap fsmain fsreg fsysram fsreplbit fsdbase fspass fsadvert ise msgqueue DEVICE_COMPONENTS= devcore iorm pmif PM_COMPONENTS= pm_default_pdd pm_mdd pm_pdd_common GWE1_COMPONENTS=wmbase gweshare gwesmain immthunk msgque GSetWinLong CePtr foreg nd idle kbdui uibase msgbeep audio GWE2_COMPONENTS=mgbase mgbitmap mgblt mgblt2 mgdc mgdibsec mgdraw mgrgn mgwinmgr tchui calibrui mggradfill mgalphablendstub mgtt mgdrwtxt mgprint mgpal mgpalnat GWE3_COMPONENTS=accel btnctl caret cascade imectl clipbd cmbctl defwndproc dlgmg r dlgmnem edctl gcache gwectrl icon iconcmn imgctl lbctl loadbmp loadimg menu me nuscrl mOverlap MouseCursorOnly iconcurs mcursor mcursor8 mNoTapUI GWE4_COMPONENTS=nclient oom sbcmn scbctl startup stcctl winmgr startui oomui sbc mnview nclientview gcacheview btnctlview stcctlview cmbctlview lbctlview msgbox msgbox_hpc dlgmgr_hpc menu_hpc EditControlOs timer column atom drawmbar hotkey s yscolor mgdx mgalias journal mgtci DCOM_MODULES= atl ole32 oleaut32 uuid OLE32_COMPONENTS=mcombase mcommem mcomstr mcommon mcomlib ole232 docfile msf exp mcomguid mcomstm GDIEX_MODULES= imaging IMAGING_COMPONENTS= img_png img_libpng img_pngdecoder img_gif img_liblzw img_g ifdecoder img_jpeg img_jpegfull img_jpegmem img_jpegdecoder img_bmp img_bmpdec oder IE_MODULES= shdocvw msxml3 urlmon wininet shlwapi uuid ieceext mlang SCRIPT_MODULES= jscript SERVERS_MODULES= obexapi obexsrvr mssoap1 wisc10 mssoapr msmqd msmqrt msmqadm ti mesvc services SHELLSDK_MODULES= aygshell SHELL_MODULES= explorer shcore ceshell qvgap CESHELL_COMPONENTS= ceshapi ceshui taskbarlist SHCORE_COMPONENTS= shcore path WCESHELLFE_MODULES= htmlview peghelp webview control ctlpnl cplmain AdvBacklight connpnl intlp Dw DwCtlPnl DwXfer bthpnl NETCF_MODULES= dotnet C:\WINCE500\PBWorkspaces\test1\WINCE500\CEPC_x86\Drivers\USB\CLASS\HID>build -c Build for Windows CE (Release) (Built on Apr 22 2004 10:38:01) File names: Build.log Build.wrn Build.err Build.dat BUILD: [Thrd:Sequence:Type ] Message BUILD: [00:0000000000:PROGC ] Checking for \WINCE500\sdk\bin\i386\srccheck.exe. BUILD: [00:0000000001:PROGC ] SrcCheck exit code: 0 (dec). BUILD: [00:0000000002:PROGC ] Compile and Link for x86. BUILD: [00:0000000003:PROGC ] Computing include file dependencies: BUILD: [00:0000000004:PROGC ] Checking for SDK include directory: C:\WINCE500\sd k\ce\inc. BUILD: [00:0000000005:PROGC ] Scan \WINCE500\PBWorkspaces\test1\WINCE500\CEPC_x8 6\Drivers\USB\CLASS\HID\HIDCLASS\MDD\ BUILD: [00:0000000006:WARNS ] RELEASETYPE is not set. Using default settings. BUILD: [00:0000000007:WARNS ] Macro: __PROJROOT not found in $(__PROJROOT)\oak\t arget\$(__CPUDIR). BUILD: [00:0000000008:WARNS ] Macro: __PROJROOT not found in $(__PROJROOT)\oak\l ib\$(__CPUDIR). BUILD: [00:0000000009:WARNS ] Macro: _COMMONPUBROOT not found in $(_COMMONPUBROO T)\sdk\lib\$(_CPUINDPATH)\coredll.lib. BUILD: [00:0000000014:PROGC ] Scan \WINCE500\PBWorkspaces\test1\WINCE500\CEPC_x8 6\Drivers\USB\CLASS\HID\HIDCLASS\USBPDD\ BUILD: [00:0000000015:WARNS ] RELEASETYPE is not set. Using default settings. BUILD: [00:0000000016:WARNS ] Macro: _COMMONPUBROOT not found in $(_COMMONPUBROO T)\oak\lib\$(_CPUINDPATH)\$(TARGETDEFNAME).def. BUILD: [00:0000000017:WARNS ] Macro: __PROJROOT not found in $(__PROJROOT)\oak\t arget\$(__CPUDIR). BUILD: [00:0000000018:WARNS ] Macro: __PROJROOT not found in $(__PROJROOT)\oak\l ib\$(__CPUDIR). BUILD: [00:0000000019:WARNS ] Macro: _COMMONPUBROOT not found in $(_COMMONPUBROO T)\oak\lib\$(_CPUINDPATH)\hidmdd.lib. BUILD: [00:0000000020:WARNS ] Macro: _COMMONPUBROOT not found in $(_COMMONPUBROO T)\sdk\lib\$(_CPUINDPATH)\coredll.lib $(_SYSGENOAKROOT)\lib\$(_CPUINDPATH)\hidpa rse.lib $(_COMMONOAKROOT)\lib\$(_CPUINDPATH)\usbclient.lib $(_SYSGENOAKROOT)\lib \$(_CPUINDPATH)\usbd.lib $(_COMMONOAKROOT)\lib\$(_CPUINDPATH)\hidmdd.lib. BUILD: [00:0000000021:WARNS ] Macro: _COMMONPUBROOT not found in \sdk\lib\x86\re tail\coredll.lib C:\WINCE500\PBWorkspaces\test1\WINCE500\CEPC_x86\cesysgen\oak\l ib\x86\retail\hidparse.lib $(_COMMONPUBROOT)\oak\lib\$(_CPUINDPATH)\usbclient.li b $(_SYSGENOAKROOT)\lib\$(_CPUINDPATH)\usbd.lib $(_COMMONOAKROOT)\lib\$(_CPUINDP ATH)\hidmdd.lib. BUILD: [00:0000000022:WARNS ] Macro: _COMMONPUBROOT not found in \sdk\lib\x86\re tail\coredll.lib C:\WINCE500\PBWorkspaces\test1\WINCE500\CEPC_x86\cesysgen\oak\l ib\x86\retail\hidparse.lib \oak\lib\x86\retail\usbclient.lib C:\WINCE500\PBWorks paces\test1\WINCE500\CEPC_x86\cesysgen\oak\lib\x86\retail\usbd.lib $(_COMMONPUBR OOT)\oak\lib\$(_CPUINDPATH)\hidmdd.lib. BUILD: [00:0000000026:PROGC ] Scan \WINCE500\PBWorkspaces\test1\WINCE500\CEPC_x8 6\Drivers\USB\CLASS\HID\CLIENTS\KBDHID\ BUILD: [00:0000000027:WARNS ] RELEASETYPE is not set. Using default settings. BUILD: [00:0000000028:WARNS ] Macro: _COMMONPUBROOT not found in $(_COMMONPUBROO T)\oak\lib\$(_CPUINDPATH)\$(TARGETDEFNAME).def. BUILD: [00:0000000029:WARNS ] Macro: __PROJROOT not found in $(__PROJROOT)\oak\t arget\$(__CPUDIR). BUILD: [00:0000000030:WARNS ] Macro: __PROJROOT not found in $(__PROJROOT)\oak\l ib\$(__CPUDIR). BUILD: [00:0000000031:WARNS ] Macro: _COMMONPUBROOT not found in $(_COMMONPUBROO T)\sdk\lib\$(_CPUINDPATH)\coredll.lib. BUILD: [00:0000000034:PROGC ] Scan \WINCE500\PBWorkspaces\test1\WINCE500\CEPC_x8 6\Drivers\USB\CLASS\HID\CLIENTS\MOUHID\BASE\ BUILD: [00:0000000035:WARNS ] RELEASETYPE is not set. Using default settings. BUILD: [00:0000000036:WARNS ] Macro: _COMMONPUBROOT not found in $(_COMMONPUBROO T)\oak\lib\$(_CPUINDPATH)\$(TARGETDEFNAME).def. BUILD: [00:0000000037:WARNS ] Macro: __PROJROOT not found in $(__PROJROOT)\oak\t arget\$(__CPUDIR). BUILD: [00:0000000038:WARNS ] Macro: __PROJROOT not found in $(__PROJROOT)\oak\l ib\$(__CPUDIR). BUILD: [00:0000000040:PROGC ] Scan \WINCE500\PBWorkspaces\test1\WINCE500\CEPC_x8 6\Drivers\USB\CLASS\HID\CLIENTS\MOUHID\LIB\STANDARD\ BUILD: [00:0000000041:WARNS ] RELEASETYPE is not set. Using default settings. BUILD: [00:0000000042:WARNS ] Macro: __PROJROOT not found in $(__PROJROOT)\oak\t arget\$(__CPUDIR). BUILD: [00:0000000043:WARNS ] Macro: __PROJROOT not found in $(__PROJROOT)\oak\l ib\$(__CPUDIR). BUILD: [00:0000000045:PROGC ] Scan \WINCE500\PBWorkspaces\test1\WINCE500\CEPC_x8 6\Drivers\USB\CLASS\HID\CLIENTS\MOUHID\LIB\TRANSCRIBER\ BUILD: [00:0000000046:WARNS ] RELEASETYPE is not set. Using default settings. BUILD: [00:0000000047:WARNS ] Macro: _COMMONPUBROOT not found in $(_COMMONPUBROO T)\oak\lib\$(_CPUINDPATH)\$(TARGETDEFNAME).def. BUILD: [00:0000000048:WARNS ] Macro: __PROJROOT not found in $(__PROJROOT)\oak\t arget\$(__CPUDIR). BUILD: [00:0000000049:WARNS ] Macro: __PROJROOT not found in $(__PROJROOT)\oak\l ib\$(__CPUDIR). BUILD: [00:0000000050:WARNS ] Directory: \WINCE500\PBWorkspaces\test1\WINCE500\C EPC_x86\Drivers\touch\trnscrbr\ does not exist. BUILD: [00:0000000053:PROGC ] Scan \WINCE500\PBWorkspaces\test1\WINCE500\CEPC_x8 6\Drivers\USB\CLASS\HID\CLIENTS\CONSHID\ BUILD: [00:0000000054:WARNS ] RELEASETYPE is not set. Using default settings. BUILD: [00:0000000055:WARNS ] Macro: _COMMONPUBROOT not found in $(_COMMONPUBROO T)\oak\lib\$(_CPUINDPATH)\$(TARGETDEFNAME).def. BUILD: [00:0000000056:WARNS ] Macro: __PROJROOT not found in $(__PROJROOT)\oak\t arget\$(__CPUDIR). BUILD: [00:0000000057:WARNS ] Macro: __PROJROOT not found in $(__PROJROOT)\oak\l ib\$(__CPUDIR). BUILD: [00:0000000058:WARNS ] Macro: _COMMONPUBROOT not found in $(_COMMONPUBROO T)\sdk\lib\$(_CPUINDPATH)\coredll.lib. BUILD: [00:0000000060:PROGC ] Saving C:\WINCE500\PBWorkspaces\test1\WINCE500\CEP C_x86\Drivers\USB\Build.dat. BUILD: [00:0000000062:PROGC ] Total of 0 pass zero files to compile in 5 directo ries. BUILD: [00:0000000063:PROGC ] Building generated files in \WINCE500\PBWorkspaces \test1\WINCE500\CEPC_x86\Drivers\USB\CLASS\HID\HIDCLASS\USBPDD\. BUILD: [01:0000000071:ERRORE] NMAKE : U1073: don't know how to make 'C:\WINCE50 0\PBWorkspaces\test1\WINCE500\CEPC_x86\cesysgen\oak\lib\x86\retail\USBHID.def' BUILD: [01:0000000073:ERRORE] NMAKE.EXE -i -c BUILDMSG=Stop. NOLINK=1 PASS0ON LY=1 CLEANBUILD=1 failed - rc = 2 BUILD: [00:0000000074:PROGC ] Files Warnings Erro rs BUILD: [00:0000000075:PROGC ] Midl 0 0 0 BUILD: [00:0000000076:PROGC ] Resource 0 0 0 BUILD: [00:0000000077:PROGC ] Message 0 0 0 BUILD: [00:0000000078:PROGC ] Precomp Header 0 0 0 BUILD: [00:0000000079:PROGC ] C/Cpp/Cxx 0 0 0 BUILD: [00:0000000080:PROGC ] Assembler 0 0 0 BUILD: [00:0000000081:PROGC ] Static Libraries 0 0 0 BUILD: [00:0000000082:PROGC ] Dll's 0 0 0 BUILD: [00:0000000083:PROGC ] Exe's 0 0 0 BUILD: [00:0000000084:PROGC ] Resx 0 0 0 BUILD: [00:0000000085:PROGC ] Csharp Targets 0 0 0 BUILD: [00:0000000086:PROGC ] Other 0 34 2 BUILD: [00:0000000087:PROGC ] BUILD: [00:0000000088:PROGC ] Total 0 34 2 BUILD: [00:0000000089:PROGC ] BUILD: [00:0000000090:PROGC ] 34 Warnings, 2 Errors Tag: Wince 4.2 to 5.0 Migration issue Tag: 84813
  - 21
    - What does this error mean? In platform builder, when i try to print i get the following error: Unknown: DEBUGCHK failed in file E:\macallan\private\winceos\osshell\commdlg\.\print.cpp at line 139 I use PRINTDLG structure and PrintDlg(&pd) function in my program. This error occurs in Platform builder when i try to use PrintDlg(&pd) function. What may be the problem? How can i resolve it? Thanks...Any help is highly appreciated :) Tag: Wince 4.2 to 5.0 Migration issue Tag: 84812
  - 22
    - Updateoverlay() is not called on WinCE5.0!! Hi all, Tag: Wince 4.2 to 5.0 Migration issue Tag: 84811
  - 23
    - CF 2.0 on headless configuration Hello, Does the CF 2.0 works on a headless configuration? Do I have to use the NULL display driver? Are there any plans to create a CF2.0 headless variant in order to minimize the memory footprint? Thanks Tag: Wince 4.2 to 5.0 Migration issue Tag: 84807
  - 24
    - USB function driver in WinCE 5.0 Dear all, I am developing a device using WinCE 5.0. Its hardware design is based on Samsung SMDK2410. I added two features to my image: "USB Function - USB Function Bus Drivers - Samsung 2410 CSP" and "USB Function - USB Function Clients - Serial". My PC machine has already installedActiveSyne. How receives me to need to do? Extremely thank! Tag: Wince 4.2 to 5.0 Migration issue Tag: 84803
  - 25
    - RequiredCEModules and DefaultDrivers in 5.0? I'm sorry if the solution is too obvious, but I can't find it. RequiredCEModules and DefaultDrivers are ignored in CEC files in PB5.0. And as I understand I should but these information in the "associated" BAT files. But how? And what BAT file is it exactly? How can I tell the PB5.0 IDE that my component A depends on component B? How can I tell the PB5.0 IDE that my default driver for display is driver C? TIA -- Michael Reim reim AT helmut-fischer DOT de Tag: Wince 4.2 to 5.0 Migration issue Tag: 84799

I am trying to migrate PXA 270 based BSP from WinCE 4.2 to 5.0; I made
all the changes in the source.cmn, make the image without compilation
error, now I am trying to download image to the platform, it is not
loading. Some flag or something is missing some where, any suggestion
will help. I read the migration from 4.2 to 5.0 many times could not
find the answer.

Top

Re: Wince 4.2 to 5.0 Migration issue by Silver

Silver
Mon May 15 19:20:03 CDT 2006

You are being rather vague.
Why not send some debug output and a description of what you are trying
to do e.g. are you downloading with serial/usb/ehternet? Which Ethernet?
etc....

Jules.Karim@Viewsonic.com wrote:
> I am trying to migrate PXA 270 based BSP from WinCE 4.2 to 5.0; I made
> all the changes in the source.cmn, make the image without compilation
> error, now I am trying to download image to the platform, it is not
> loading. Some flag or something is missing some where, any suggestion
> will help. I read the migration from 4.2 to 5.0 many times could not
> find the answer.
>

Top

Re: Wince 4.2 to 5.0 Migration issue by Jules

Jules
Mon May 15 19:45:40 CDT 2006

Sorry for not to be detail, actually I am loading from CF card to
onboard flash card.

Top

Re: Wince 4.2 to 5.0 Migration issue by Bruce

Bruce
Tue May 16 21:56:49 CDT 2006

Jules:

Where is it failing? Loading the image, starting the image, while the image
is running...

--
Bruce Eitman (eMVP)
Senior Engineer
beitman AT applieddata DOT net

Applied Data Systems
www.applieddata.net
An ISO 9001:2000 Registered Company
Microsoft WEP Gold-level Member

<Jules.Karim@Viewsonic.com> wrote in message
news:1147740340.491718.57550@g10g2000cwb.googlegroups.com...
> Sorry for not to be detail, actually I am loading from CF card to
> onboard flash card.
>

Top