WTD: Win CE Platform Builder 2.11

Tutorials Win: Microsoft Windows Forum

- Previous
  - 1
    - MultiXIP and AUTOSIZE_ROMGAP problem Hi, I am trying to build and download an image into NAND flash with BINFS on my platform. The built OS image is about 19MB in size. However I would like to extend the region size for the NK.bin with AUTOSIZE_ROMGAP to about 32MB, so that I can expand this XIP region in the future without affecting other regions/partitions in my NAND flash memory. I have set ' AUTOSIZE_ROMGAP NK D34508 ' and ' ROM_AUTOSIZE=ON '. However the NK.bin built is still 19MB only, instead of 32MB. Does anyone know what the problem might be and how to resolve it? Below are the config.bib settings used: ======================================================================= MEMORY #define CHAIN_ADDRESS 82000000 CHAIN $(CHAIN_ADDRESS) 00001000 RESERVED pdwXIPLoc 00000000 $(CHAIN_ADDRESS) FIXUPVAR NK 80001000 01FFF000 RAMIMAGE CHAIN 82000000 00001000 RESERVED IF IMGNOKITL RAM 82001000 01FFF000 RAM ELSE RAM 82001000 01FDF000 RAM KITL 83FE0000 0001F800 RESERVED BOOTARGS 83FFF800 00000800 RESERVED ENDIF FLASH 9E000000 01C00000 RESERVED CONFIG COMPRESSION=ON KERNELFIXUPS=ON ; Multi-Region ; AUTOSIZE=ON ; AUTOSIZE is used to enable the following flags. RAM_AUTOSIZE=ON ROM_AUTOSIZE=ON DLLADDR_AUTOSIZE=ON XIPSCHAIN=$(CHAIN_ADDRESS) AUTOSIZE_ROMGAP NK D34508 AUTOSIZE_DLLADDRGAP=0 AUTOSIZE_DLLDATAADDRGAP=0 AUTOSIZE_DLLCODEADDRGAP=0 IF IMGPROFILER PROFILE=ON ELSE PROFILE=OFF ENDIF IF IMGSRE SRE=ON ELSE SRE=OFF ENDIF ; ; ROMFLAGS is a bitmask of options for the kernel ; ROMFLAGS 0x0001 Disallow Paging ; ROMFLAGS 0x0002 Not all KMode ; ROMFLAGS 0x0010 Trust Module only ; IF IMGTRUSTROMONLY IF IMGNOTALLKMODE ROMFLAGS=12 ELSE ROMFLAGS=10 ENDIF ELSE IF IMGNOTALLKMODE ROMFLAGS=02 ELSE ROMFLAGS=00 ENDIF ENDIF ---------------------------------------------------------------------------- ------------------------------------------- The build output is as follows: 8100effc 4 80b37ffc 4 80967ffc 4 81059ffc 4 80658ffc 4 800c6ffc 4 804e1ffc 4 80530ffc 4 80213ffc 4 80d9effc 4 81061ffc 4 total space 97012 in 87 ranges Warning: FixupVar pdwXIPLoc not found in kernel. Variable not fixed up. Writing C:\WINCE420\PUBLIC\MSDBAu1500\RelDir\AMD_DB~2\NK.bin Table of contents 812c93e8 00001688 ( 5768) Writing ROM signature and TOC pointer at 80001040 Kernel data copy section 804e2ec4 00000020 ( 32) ROM Header 812c9394 00000054 ( 84) First DLL code Address: 02c90000 Last DLL code Address: 04000000 First DLL Address: 01ed01f3 Last DLL Address: 02000000 Physical Start Address: 80001000 Physical End Address: 812caa70 Start RAM: 82000000 Start of free RAM: 82049000 End of RAM: 83fdf000 Number of Modules: 105 Number of Copy Sections: 2 Copy Section Offset: 804e2ec4 Kernel Flags: 00000002 FileSys 4K Chunks/Mbyte: 128 <2Mbyte 128 2-4Mbyte 0 4-6Mbyte 0 >6Mbyte CPU Type: 0166h Extensions Pointer: 80005370 Total ROM size: 012c9a70 ( 19700336) Starting ip: 80001004 Raw files size: 002d6327 Compressed files size: 001707b7 Compacting bin file... Combining bin files... Compacting bin file... Done! Failed calling bin2xip.exe C:\WINCE420\PUBLIC\MSDBAu1500\RelDir\AMD_DB~2\chain.bin C:\WINCE420\PUBLIC\MSDBAu1500\RelDir\AMD_DB~2\privkey.dat makeimg: Check for C:\WINCE420\PUBLIC\MSDBAu1500\RelDir\AMD_DB~2\PostRomImage.bat to run. makeimg: Check for C:\WINCE420\PUBLIC\MSDBAu1500\RelDir\AMD_DB~2\PostMakeImg.bat to run. After the built, I can see the NK.bin(19,138MB), chain.bin(1KB), XIP.bin(19,139MB), and chain.lst in the _FLATRELEASEDIR . Is the following warning messages the cause of my problem? Does anyone know why I am getting this messages and how to resolve it?? Thanks in advance! >> Warning: FixupVar pdwXIPLoc not found in kernel. Variable not fixed up. >> Failed calling bin2xip.exe C:\WINCE420\PUBLIC\MSDBAu1500\RelDir\AMD_DB~2\chain.bin C:\WINCE420\PUBLIC\MSDBAu1500\RelDir\AMD_DB~2\privkey.dat Paul W Tag: WTD: Win CE Platform Builder 2.11 Tag: 38960
  - 2
    - [Q] How to make Compact Framework SDK I use PB4.2, XScale platform. I made SDK for eVC4. (Platform->Settings...) But, when I make SDK for Compact Framework, I had some problems. Only help files is included into SDK. Below is packinglist file content. Do I install VS.net to build SDK for Compact Framework? "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wcebluetooth.chm" _0WCEBLU_1_CHM "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wcewave.chm" _0wcewave_chm "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wcedshow.chm" _0wcedshow_chm "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wcewmt.chm" _0wcewmt_chm "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wcewmp.chm" _0wcewmp_chm "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wceauthservices.chm" _0WCEAUT_1_CHM "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wcecrypto2.chm" _0WCECRY_2_CHM "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wcecrypto.chm" _0WCECRY_1_CHM "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wcedialup.chm" _0WCEDIA_1_CHM "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wcetapi.chm" _0wcetapi_chm "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wcevpn.chm" _0wcevpn_chm "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wceredir.chm" _0wceredir_chm "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wcewinsock.chm" _0WCEWIN_2_CHM "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wceeap.chm" _0wceeap_chm "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wcecmdprocess.chm" _0WCECMD_1_CHM "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wcenetui.chm" _0wcenetui_chm "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wceinput.chm" _0wceinput_chm "E:\PDA\MC1400FW\SDK\MC1400FW\Help\Wcestylus.chm" _0WCESTY_1_CHM "E:\PDA\MC1400FW\SDK\MC1400FW\Help\Wcepointer.chm" _0WCEPOI_1_CHM "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wceactsync.chm" _0WCEACT_1_CHM "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wcepie.chm" _0wcepie_chm "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wcejscript.chm" _0WCEJSC_1_CHM "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wcevbscript.chm" _0WCEVBS_1_CHM "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wceiemlang.chm" _0WCEIEM_1_CHM "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wcewininet.chm" _0WCEWIN_1_CHM "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wceurlmon.chm" _0WCEURL_1_CHM "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wceldap.chm" _0wceldap_chm "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wceunisdk.chm" _0WCEUNI_1_CHM "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wceobex.chm" _0wceobex_chm "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wcemsmq.chm" _0wcemsmq_chm "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wcesoap.chm" _0wcesoap_chm "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wcexmlxql.chm" _0WCDA83_1_CHM "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wcexmldom.chm" _0WCEXML_2_CHM "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wcefonts.chm" _0wcefonts_chm "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wcelocal.chm" _0wcelocal_chm "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wceui40.chm" _0wceui40_chm "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wceoverview.chm" _0WCEOVE_1_CHM "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wcesdk40.chm" _0wcesdk40_chm "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wcekernel.chm" _0WCEKER_1_CHM "E:\PDA\MC1400FW\SDK\MC1400FW\Help\wceobjstore.chm" _0WCEOBJ_1_CHM "E:\PDA\MC1400FW\SDK\MC1400FW\Help\Wceprint.chm" _0Wceprint_chm "E:\PDA\MC1400FW\SDK\MC1400FW\help\{1DF833C4-AE35-453D-844A-FF994F1187D8}.ch m" _0_1DF83_1_CHM "E:\PDA\MC1400FW\SDK\MC1400FW\MSManifest.txt" _1MSMANI_1_TXT Tag: WTD: Win CE Platform Builder 2.11 Tag: 38958
  - 3
    - How to remove the standard shell and startup application automically after start of windows ce? How can I make my application automatically startup after the load of windows ce and at the same time remove the begin menu , my computer, and so on , that is I want to the user not to see the windows ce standard UI and the application startup directly. My Platform configuration is PDA or Mobile HandHeld. I can make my application automatically startup after the load of windows ce at the standard shell through make a link file of my application into the startup directory ( \ windows\startup\myapplication.lnk). but when I change the standard shell into taskman shell, my application cannot automatically startup after the load of windows ce, I donot know why? Can you help me? Think you very much! Tag: WTD: Win CE Platform Builder 2.11 Tag: 38955
  - 4
    - Hive based registry - what is saved on RegFlush Hi, we currently use the hive mechanism to keep registry settings on a disk (compact flash card). Actually only a few registry keys need to be persistent . For example the touch calibration settings of a touch screen driver. It works ... but I see that the hive files are not only saving what we want to save. After reboot from a CF card that was in an identical hardware before, (maybe with the exception of the network adapters MAC address) the DHCP often doesn't work any more. I just don't get a valid address. After deleting the hive files and restart it works fine again. If a DHCP server gives me an IP address and other nework config data, is it going to the registry hive ? I think so, all delta is saved according to the documentation. Does that cause our problems ? Another strange effect: A USB keyboard plugged in ... works. Then: boot without the usb keyboard. When I then boot with the keyboard attached it doesn't work until I unplug and replug it. Also... removing hive files solves the problem. The same with PC card slot. CE behaves slightly different if there was a card in the slot last time or not or never since the hive file was created. Some things are just dynamic in our CE system. I came to the conclusion that it is safer not to use hive but to save the settings in my known reg keys in my own binary file and to register our ocx Controls every boot time again with a call to DllRegisterServer. The system also boots faster without hive based registry. Has anyone observed the same ? Maybe I can exclude registry keys from persistence ? Is there a better solution to the problem ? Stephan Tag: WTD: Win CE Platform Builder 2.11 Tag: 38942
  - 5
    - graphedit and wince 4.0 i'm trying to build Graphedit for use on a x86 wince 4.0 device for testing purposes and I can't seem to get it to add it in. I've tried the following in the environment settings (SYSGEN_GRAPHEDT with a variable of 1) No dice. I get a (cannot find requested system_graphedt in the catalog) any ideas? - Nick Beals nbeals@enxnet.com Tag: WTD: Win CE Platform Builder 2.11 Tag: 38939
  - 6
    - VMINI, PING & 4.2 Residential Gateway Config We just recently switched my Residential Gateway project to Windows CE 4.2 (from 4.1) to pick up the new features for gateways and found an issue we can find no documentation on. We are using the "residential gateway" configuration for our project (ARMV4I). When we enable KITL, do a debug build and run it on our device, we are no longer able to PING the device or HTTP out to it. The device is also not able to PING the PC it is connected to. Since the device only has one Ethernet port we use VMINI to share that port between KITL and the Networking stack. This worked perfectly in WinCE 4.1 and it works perfectly if we do a retail build with KITL and VMINI disabled. What do we need to change between 4.1 and 4.2 in our VMINI network configuration to get this to work? Mark Moeller Qualnetics Corporation Tag: WTD: Win CE Platform Builder 2.11 Tag: 38936
  - 7
    - Puting Margion on Desktop Question? Need to put margion on Desktop of CE PC Shell, such that the Icons are about One inch from Left and top of screen. Do's anyone have any ideas? or can anyone steare me to doc? Tag: WTD: Win CE Platform Builder 2.11 Tag: 38934
  - 8
    - PCMCIA i82365 compatible or TI1250? My ActionTec PC750 PCMCIA reader uses the TI1225 chipset as the PCMCIA controller. Which driver I need to use in CEPC? PCMCIA i82365 compatible or TI1250? Tag: WTD: Win CE Platform Builder 2.11 Tag: 38924
  - 9
    - View a PDF from inside IE I've got a customer asking if it's possible to view PDFs inside IE like on the desktop. I did a quick 4.1 build and it appears you have to download it and then view the local copy, but I just wanted to get confirmation. Does anyone know if the PDF viewer can be used inside either IE or PIE on 4.1 or 4.2? I can try each, but I'm hoping just asking will be quicker. -- Chris Tacke, eMVP Advisory Board Member www.OpenNETCF.org --- Windows CE Product Manager Applied Data Systems www.applieddata.net Tag: WTD: Win CE Platform Builder 2.11 Tag: 38914
  - 10
    - Propagate the auto Device Name from bootloader into OS settings Microsoft.public.windowsce.embedded or Microsoft.public.windowsce.platbuilder Hi, I am developing for a headless device with Windows CE.NET 4.1. The idea is to read the Boot parameters network name that is automatically built in bootloader, and rewrite in the registry the machine name just after the initialization of the registry. The OAL will take BootParams.WinceBootArgs.szDeviceNameRoot and change the registry value [HKEY_LOCAL_MACHINE\Ident, Name] with BootParams.WinceBootArgs.szDeviceNameRoot in IOCTL_HAL_INITREGISTRY in OEMIOControl(). But always I am having exception in NK.exe (access violation) !!! In OEMInit() when I print with DEBUGMSG() the pBootArgs->szDeviceNameRoot it is not containing the same value that was built in the bootloader by CreateDeviceName() Why? Is there any other way to let me propagate the Device Name (and some network parameters (IP, ..)...) Which are built in Bootloader to the OS setting? Any samples, any link, ...is very appreciate. Thank you very much for you help. Tag: WTD: Win CE Platform Builder 2.11 Tag: 38913
  - 11
    - Move platform workspace to a different computer? What files from my project folder are essential to move to a different computer with a fresh Platform Builder installed in order to continue work on my custom platform? I have moved *.pbw and *.wce but it does not seem to be enough. Tag: WTD: Win CE Platform Builder 2.11 Tag: 38910
  - 12
    - Good old SA1110 PCMCIA and CE 4.2 :) Hi, I'm having trouble with the PCMCIA driver for CE 4.2. When I warm/cold boot my device with a CISCO 350 series pcmcia card inserted the driver crashes (device.exe) and will not load any PCMCIA cards hereafter. However, if I have some other PCMCIA card inserted upon a warm/boot, e.g. a wired ne2000 compatible card, the driver loads without any problems. If I then unplug the wired card and insert a CISCO card the driver also loads fine. It seems there are some delay problems in loading the cisco driver upon startup. In CE 4.1 I had no problems (using SA1110 BSP with the same drivers as in 4.2). Below is some debug information: 0x8df93000: PCMCIA: DEBUGCHK failed in file d:\mckendric\public\common\oak\drivers\pcmcia\mdd\load.c at line 763 0x8df93000: DEBUG_BREAK @0306c144 MD=1f Ignored. 0x8df93000: PCMCIA PDCardSetSocket 0x8df93000: PCMCIA PDCardSetSocket Powersettings 0x8df93000: SetSOCK Powering Socket 1 .... .. . I looked up the line in load.c and found a DEBUGCHK(pPsock->hLoad == NULL); Does anyone know what the problem is here? Best regards, Bo Henriksen NordicID Tag: WTD: Win CE Platform Builder 2.11 Tag: 38895
  - 13
    - right shifted TFT display with CE4.2 hello, I connected a CRT and a panel VGA TFT display to an eValue ECM 3412 board. After some troubles I got a valid "picture" in the correct size on both devices. Now my problem is, that the picture on the TFT display is shifted to the right by approximately 2 cm. I tried a lot of different resolutions, and setups (even TV horizontal shift) but I found no way to correct this. With CE 4.1 the display worked correctly. I would be very grateful for any ideas because mine ran out. :-( regards, Oswald Boehm ========================================= BRAINCON Technologies ========================================= Software Development Innstrasse 24 A-1020 Vienna AUSTRIA Tel.: +43-1-61067 0 Fax: +43-1-61067-93 Email: o.boehm@bct.co.at http://www.braincon.com/ ---------------------------------------------------------------------------- ------ Tag: WTD: Win CE Platform Builder 2.11 Tag: 38893
  - 14
    - CE 4.2 clears the RTC and RTC-RAM Hello, we have a big problem. After every boot of win ce 4.2 the RTC an teh RTC-ram ist cleared. Tag: WTD: Win CE Platform Builder 2.11 Tag: 38891
  - 15
    - =?iso-8859-1?Q?Intrinsyc_=B5PDA?= Looking for references regarding Intrinsyc =B5PDA. Need to=20 develop code for the BSP. Any information regarding=20 debuging tools for the BSP, or experience in developing=20 code for it will be appretiated. Tag: WTD: Win CE Platform Builder 2.11 Tag: 38890
  - 16
    - Interrupts on CEPC Hi, My target is a CEPC. I have a hardware attached to the target's ISA bus. This hardware is capable of activate IRQ 7 line. I'm using Platform Builder 4.01. I wish to write an application capable of doing something when IRQ 7 activate. I would like to do it as simple as possible. Would you help me? Would you send me some sample code? Thanks Tag: WTD: Win CE Platform Builder 2.11 Tag: 38879
  - 17
    - urgent! can you help me! I am ersearching about AER（advanced exeception reporting) under platform builder4.2, and want to use this mechanism to handle the exception thrown by application.so,can anyone tell me how to do it ,or where can i find some documents about AER,or some website introducing AER.can you help me? thanks in advance. Tag: WTD: Win CE Platform Builder 2.11 Tag: 38873
  - 18
    - TFAT Questions TFAT Questions: System Description: We are using WinCE 4.2 on an Intel x86 platform with either a hard disk or Compact Flash (CF). We utilize the WinCE DOS Boot-Loader to boot WinCE. We us a hive-based registry which persists on the hard disk along with the nk.bin file and several other system configuration files and web pages. Currently the system boots on a DOS FAT16 formatted partition. We want to enable the WinCE 4.2 TFAT feature to provide maximum system reliability. 1) Should we format the primary disk partition as TFAT for maximum reliability? Can WinCE even boot from a pure TFAT formatted partition? Or alternatively, should we use a regular FAT16 partition with the registry configured to create a second FAT table, and then treat the partition as if it were TFAT? If the bootable partition can be formatted as TFAT, we have the following questions regarding preparing the hard disk (or CF) image. All WinCE documentation regarding preparing a hard disk and loading the DOS Boot-Loader refer to using DOS utilities. A)How can we create the pure TFAT16 formatted partition? Do we first have to load WinCE and use its format utility, or is there a TFAT format utility for DOS? B)Will the CeSys.exe utility recognize a TFAT partition, and correctly load the disk boot sector so the system will correctly find the DOS Boot-Loader. C)Can a TFAT formatted disk be duplicated using standard disk imaging tools such as Symantec Ghost or Power Quest Drive Image? These tools are commonly used in the PC world. If these tools will not work with TFAT, can you recommend other tools that will replicate a TFAT partition? If the bootable partition CANNOT be formatted as TFAT, then there are the following questions: D)TFAT will not transact files in the hard disk root directory. This is typically where we put our nk.bin file. Should this file, and all other root directory files, be relocated under the special "__TFAT_HIDDEN_ROOT_DIR__" directory so as to provide maximum system reliability? Or is this not necessary? 2) Once a CF disk has been used as a TFAT partition under WinCE, is there any way to delete files on the CF disk when accessing it through a CF card reading on a desktop workstation? It would be nice to have utilities to modify TFAT disks when accessed by a standard XP desktop system. It is a common development practice here to take a CF disk, then modify, delete, or copy files on it from a desktop workstation, then put the CF disk back into the WinCE machine and run it from there. Using a TFAT formatted CF disk puts a wrinkle in this practice, as the desktop OS (XP) does not natively handle TFAT. Any suggestions for ways to correctly access a TFAT formatted CF disk from a XP workstations? Thanks for Any positive information! Tag: WTD: Win CE Platform Builder 2.11 Tag: 38866
  - 19
    - Where are my drivers I'm building a BSP. BP-4.2. I've been using the BSP Wizard and things are going ok. I save my work and now when I come back I see only a portion of the drivers that I've entered. In particular I have an audio driver and dma driver shown. I see only these 2 drivers in the CATALOG window of PB and when I use the BSP Wizard and select that I want to add drivers to a BSP it shows me only those same 2 drivers. YET, in the CEC file that I've created with the Wizard ( and have not fiddled around with it by hand) I have many more driver entries. What's going on ? Finecats Tag: WTD: Win CE Platform Builder 2.11 Tag: 38865
  - 20
    - PCMCIA reader problem I have a ActionTec PCI750 PCMCIA reader. I built a CEPC followed the tutorial except add PCMCIA(TI1250) feature. I am using PB 4.2 to build it and no error/warning. But after downloading, the target CEPC reboot again and image downloaded again. The reboot/downloading repeats again and again - more than 10 times until I disconnect or shut down target PC. But using PB4.1, no such a problem. why? Tag: WTD: Win CE Platform Builder 2.11 Tag: 38862
  - 21
    - boot CEPC from hard disk First, I have built a CEPC with KITL enabled followed the help file "How to ...". And everything is OK. Then, I built same CEPC with KITL disabled(renamed as NO_KITL_NK.bin). I copied it to target CEPC hard disk and rename back to NK.bin. Now my hard disk has 2 files: nk.bin and BLDR. Then I restart my CEPC. But system halted there - black screen with 1 cursor blinking on left top corner. Which step I missed? Thanks for all your inputs. Tag: WTD: Win CE Platform Builder 2.11 Tag: 38859
  - 22
    - QFE question If I installed current QFE(April - June 2003). Do I need to install old QFEs? Tag: WTD: Win CE Platform Builder 2.11 Tag: 38854
  - 23
    - QFE question If I installed current QFE(April - June 2003). Do I need to install old QFEs? Tag: WTD: Win CE Platform Builder 2.11 Tag: 38853
  - 24
    - newbie question: bootable OS image Hi, I built a platform builder project for "PDA or Mobile Handheld", then I downloaded the 'nk.nb0' file (from release directory) to my development board (DBPXA250), but my development board didn't started the Windows CE. How could I create a bootable WCE image? I would like to use the JTAG cable to write my OS image and then restart my development board and then see the WCE running. thanks in advance. -- Edgard Lima Tag: WTD: Win CE Platform Builder 2.11 Tag: 38840
  - 25
    - WMI This is a multi-part message in MIME format. ------=_NextPart_000_0019_01C355A4.9C790440 Content-Type: text/plain; charset="Windows-1252" Content-Transfer-Encoding: quoted-printable Is WMI supported on any CE/PPC platform? If not, are there any plans to = support it in the future? ------=_NextPart_000_0019_01C355A4.9C790440 Content-Type: text/html; charset="Windows-1252" Content-Transfer-Encoding: quoted-printable <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN"> <HTML><HEAD> <META http-equiv=3DContent-Type content=3D"text/html; = charset=3Dwindows-1252"> <META content=3D"MSHTML 6.00.2800.1170" name=3DGENERATOR> <STYLE></STYLE> </HEAD> <BODY bgColor=3D#ffffff> <DIV><FONT size=3D2>Is WMI supported on any CE/PPC platform? If not, are = there any=20 plans to support it in the future?</FONT></DIV></BODY></HTML> ------=_NextPart_000_0019_01C355A4.9C790440-- Tag: WTD: Win CE Platform Builder 2.11 Tag: 38836
- Next
  - 1
    - PB 4.2 ignoring BOOTME requests So I've finally got my bootloader sending bootme broadcasts over the network (tested with a packet sniffer and contents look sane) but PB 4.2 just says "Waiting for BOOTME" . The device name appears in the list of Available Devices for download, but PB seems to be ignoring the bootme requests. The network setup is reasonably simple - the dev board and the second network card in my PC are connected via a hub. Is there any extra logging information that might help me locate the source of this problem? Many Thanks, James Tag: WTD: Win CE Platform Builder 2.11 Tag: 38834
  - 2
    - CE4.2 hangs up on 10 second when click disabled control subj On CE4.1 such wasn't Regards Olefard Tag: WTD: Win CE Platform Builder 2.11 Tag: 38831
  - 3
    - NDIS EnterCriticalSection DEBUGCHK in CE 4.2 - HELP! Hey guys. I've been dealing with this problem for a while now, hoping that it would somehow get fixed. Unfortunately, it's still a problem for me, and it's getting more annoying and more troublesome as time goes on. Here's my original post on the subject: http://groups.google.com/groups?hl=en&lr=&ie=UTF-8&oe=UTF-8&safe=off&threadm =3f030f26%241%40news.microsoft.com&rnum=8&prev=/groups%3Fq%3DMurawski%2Bgrou p:microsoft.public.windowsce.platbuilder%26hl%3Den%26lr%3D%26ie%3DUTF-8%26oe %3DUTF-8%26safe%3Doff%26scoring%3Dd%26selm%3D3f030f26%25241%2540news.microso ft.com%26rnum%3D8 Here's a post from Steve Maillet where he lists it as bug #7 in his list of known CE 4.xx bugs: http://groups.google.com/groups?q=Maillet+group:microsoft.public.windowsce.p latbuilder&start=90&hl=en&lr=&ie=UTF-8&oe=UTF-8&safe=off&scoring=d&selm=eB72 YpWQDHA.2316%40TK2MSFTNGP12.phx.gbl&rnum=97 Basically, what's happening is this. When I have a PCMCIA card in my device at cold boot, NDIS occasionally hits a DEBUGCHK in the kernel when trying to enter a critical section that has never been initialized. Since I don't have access to NDIS code, I can't really tell what's going on, but the call stack looks like this: <stack dump> COREDLL!EnterCriticalSection(CRITICAL_SECTION * 0x01fd98c0 PcmciaMemListLock) line 90 + 76 bytes NDIS!mapAllWindowsForHSock(_CARD_SOCKET_HANDLE {...}, int 0x00000001, int (_NDIS_PCMCIA_WINDOW *)* 0x03d6a954 npwMapToDevice(_NDIS_PCMCIA_WINDOW *)) line 478 NDIS!PcmciaCallBack(unsigned int 0x00000040, _CARD_SOCKET_HANDLE {...}, _CARD_EVENT_PARMS * 0x080afdf0) line 620 PCMCIA!CallClient(unsigned int (unsigned int, _CARD_SOCKET_HANDLE, _CARD_EVENT_PARMS *)* 0x00000000, unsigned int 0x01fa8aa0, _CARD_SOCKET_HANDLE {...}, _CARD_EVENT_PARMS * 0x00000000, _CLIENT_DRIVER * 0x2dfa5fda) line 600 + 24 bytes PCMCIA!CallbackThread(unsigned int 0x00000000) line 910 + 56 bytes COREDLL!ThreadBaseFunc(void * 0x03a6aecc CallbackThread(unsigned int), unsigned long 0x00000000) line 418 + 16 bytes </stack dump> Unfortunately, this problem is probably much more serious for me than it is for most CE platforms. Our device ALWAYS has a PCMCIA card in it, and it goes through a cold boot quite often. I seem to hit this problem almost every time my platform boots. To make things worse, about 50% of the time when it happens, and I try to run past the DEBUGCHK, I hit another critical access violation in NDIS. (I guess there's a critical section somewhere for a reason!) Does anyone have any new information on this problem? Any suggestions on what I should do? I've been dreading trying to call Microsoft about it directly. I haven't had much luck trying to describe problems of anything beyond trivial technical complexity with the first one or two levels of technical support. Should I suck it up and put in a call on this one? Thanks in advance guys. Mark Murawski Vocollect, Inc. Tag: WTD: Win CE Platform Builder 2.11 Tag: 38827
  - 4
    - Batch build makeimg wince300 Hello, I am trying to configure a command line build for our project under WinCE 3.0. I want to be able to make an image of my platform (from the build directory) without having Platform Builder installed. We want this particular configuration, so that the application programmer in our firm will be able to build new images without having to install PB (since they won't use it anyway). To realize it, I copied the build directory of my project (which have the files generated after the the buildrel phase) and I've created a bat file which contains set all the necessary variables and path. I also copied the C:\WINCE300\PUBLIC\COMMON\OAK\BIN\I386 (to be able to use makeimg.exe and the programs needed to create the image). To use this package, I copy all the files in c:\wince300Img and then I run my batch file to set the variable and then I called makeimg to build the image. I test it and it works great on a computer with PB 3.0 already installed, but It doesn't work on my test machines which don't have PB installed (which is my goal!) On my test machines, the makeimage build stop always after the InitRegistry phase, and before it copies nknodebug.exe to nk.exe (I know that before I compared it with a "working" make image). Here's a snapshot: (...) InitRegistry Finished (875 lines). MAKEIMG: localization SKIPPED since COUNTRY is unchanged Windows CE ROM Image Builder v3.0 Copyright (c) 1995-2000 Microsoft Corporation Failed romimage c:\WINCE300Img\rev_5_16\release\ce.bib Failed romimage c:\WINCE300Img\rev_5_16\release\ce.bib I really don't understand what I am doing wrong. I must be forgetting a setting somewhere. I checked and re-checked all the system variables between my test machines and my machine with PB and everything is the same. I also try to copy the PB directory (and adding it to my path and CEPBDir variable) to one of my test machine to check if maybe a file was needed there... but I also had no luck. Here's the list of the system variable that I am setting in my batch file. rem ----------------------- rem Environment Settings rem ----------------------- SET DRIVE=c: Set ComSpec=C:\WINDOWS\system32\cmd.exe Set COUNTRY=USA Set IMGNODEBUGGER=1 Set _HOSTCPUTYPE=i386 Set _TGTCPUTYPE=MIPS Set _WINCEROOT=%DRIVE%\WINCE300Img\rev_5_16 Set _PUBLICROOT=%_WINCEROOT% Set _FLATRELEASEDIR=%_WINCEROOT%\release Set BIRCH=1 Set BUILD_DEFAULT=-e -w -nmake -i Set CEPBDir=C:\Programme\Windows CE Platform Builder\3.00 Set COUNTRY=USA Set HOMEDRIVE=C: Set HOMEPATH=\ Set IMGFLASH=1 Set IMGNODEBUGGER=1 Set MAXALL2_NOCURSOR=1 Set USE_DBGSER=NONE Set WINCECOD=1 Set WINCEDEBUG=retail Set WINCEMAP=1 Set _CURSLMTREE=pnt Set _DEPTREES=winceos msmq ie wceshell wceshellfe wceapps wceappsfe Set _PLATFORMDRIVE=C: Set _TGTCPU=R3000 Set _TGTCPUTYPE=MIPS Set _TGTOS=CE Set _TGTPLAT=puvplat Set _TGTPROJ=puvprog Set _WINCECALLED=1 Set _WINCEDRIVE=C: Set _WINCEEXTERNAL=1 Set _WINCEOSVER=300 Set MYPATH=%PATH% SET PATH=%PATH%;c:\WINCE300Img\rev_r5_6\release\bin\i386\; This solution already work for the wince212 version of our project, the batch file was greatly inspired from there (maybe this is the problem...) If someone has any clue, I would apreciate it! Thanks, Jean-François Thibeault Tag: WTD: Win CE Platform Builder 2.11 Tag: 38824
  - 5
    - How PDA Defence works? Hi, I downloaded win ce 3.0 PDA Defence evalution software and installed in my device. I would like to know the implementation logic of safe folder bcoz i tried to look into the registry setting any FSD is assosiated to the safe folder, but couldn't find any such entry. I would be glad if someone tell me how the PDA Defence safe folder been implemented. rgds GP. Tag: WTD: Win CE Platform Builder 2.11 Tag: 38807
  - 6
    - can i surf the internet using wince through USB port HIHI can i surf the internet using wince through USB port can anyone tell me the details? thx a lot Roy Tag: WTD: Win CE Platform Builder 2.11 Tag: 38806
  - 7
    - Multicast problem (high Packet loss) I am using windows CE 4.2. I am testing Streaming Media using Windows Media Player which is Multicasted from a media server. I am testing on 2 types of X86 targets, one was build by our hardware engineer (lets say embedded bord)and other was VIA make. Both had exactly same components. When i am testing (playing) a multicast media on embedded board there is a packet loss of 20% with in the same network. But when i am testing on VIA board which is also on the same network these is a packet loss of 70%.( a bit surprising). In the case of TCP (unicast) both are working fine. I know it is not good to ask you all, What is the exact problem. But i need all of your suggesions in regard, where can be the problem. IS it the software problem? OS is same, all the drivers are same and of the same version. The only difference is on the target board i am using VIA CEPC and on the VIA board i am using MS CEPC. IS it the hardware problem? Both have the same Ethernet and more over in the case of Unicast (TCP) they r working fine. Is it the problem related to buffers? is there any way to increase the datagram buffers in CE 4.2. If i am developing my own application to play the media i can increase using some APIs. But i need a genaric one. Can all of you please give ur sugg. in regarding this problem. Tag: WTD: Win CE Platform Builder 2.11 Tag: 38803
  - 8
    - Future of Data Access on Windows CE? Hi all, I have been reviewing articles on this newsgroup with regard to the use of ADOCE and CE.NET platform. The result of this review is that Microsoft recommends that for future development that ADO.NET be used for data access. I find this position problematic for headless devices. Currently, we use ADOCE to access an OLEDB driver for a third party from ASP pages on a headless device. Microsoft's stand is that we should move to ADO.NET. There are two problems with this for our targeted system. 1) ADO.NET requires the .NET Compact Framework and this is only available on devices with display. 2) The addition of the .NET Compact Framework to the OS takes valuable resources when it is really not needed for anything else. I understand that Microsoft have a strategy for rolling out .NET Framework and incorporating Windows CE into this framework, but I think that they may have dropped the ball on this one. When embedded devices are being developed there are many tradeoffs made between cost and functionality - this is true whether the device has a display or not. But being forced to add the .NET Compact Framework because we wish to have database access from the Web Server (for example), seems a bit heavy handed IMHO. It also (currently) mandates a device with a display. I think that some thought needs to be put into the realm of headless devices and the functionality that they require. What do others think? Maybe we can get Microsoft to re-assess this situation for the future. Regards, Brian Tag: WTD: Win CE Platform Builder 2.11 Tag: 38801
  - 9
    - migrate from 3.0 to 4.2 Now that I have finished work on wince 3.00 and is working on our platform and is stable :0)....We are moving to wince.net 4.2. Our BSP is based on the intel_sa1110_assabet. From what I have read The Intel SA1100/SA1111 (Assabet) Development Kit is no longer available for purchase. Therefore, the BSP for this hardware platform is not included in Platform Builder 4.2 and is no longer supported. If your development platform requires the Intel SA1100/SA1111 (Assabet) Development Kit and the platform directory for testing or other purposes, you can use the BSP for the Intel XScale DBPXA250 Development Platform, which has been enabled to support ARMV4 builds, or you can use another suitable BSP from a third-party vendor. However, Platform Builder 4.2 still supports the Intel SA1100/SA1111 (Assabet) Development Kit CSP drivers for the integrated peripherals on the SA1100 CPU or the SA1111 CPU companion chip. Refer to %_WINCEROOT%\Public\Common\Oak\CSP for these drivers. I'm confused, as far as I understand from the above once I have installed wince 4.2 (I am doing this tomorrow) I can install the ARMV4I option (I'm not installing ARMv4) I can build code for the SA1110 StrongArm. Can I copy the Intel_sa1110_assabet BSP from wince 3.00 and build an image to run on the assabet, it would be useful and would provide immediate feedback. Or will I have to take the Intel Xscale DBPXA250 and integrate/cobble in our drivers, oal, bootloader etc.. I don'y have a feel for how much work is involved, is it weeks or months.... Any advice would be appreciated Regards Tariq Tag: WTD: Win CE Platform Builder 2.11 Tag: 38799
  - 10
    - SIP disable Hi, On our platform, the user will typically have a keyboard. Usually, this keyboard is a full ASCII and numeric unit, so there's no need for a SIP. However, there are situations where a user might have only a numeric keyboard and want the SIP for rare alpha input (an operator's name, maybe, entered once per day). So, I don't want the SIP popping up, by default, any time an EDIT field is selected, but I don't want to completely remove SIP support. My initial strategy for this was to implement my own SIP, which would be the default. This default SIP would do nothing (no window popup, no resizing of dialogs, etc.) When this SIP was selected, then, it would be very much like having no SIP at all in the system (design goal #1 met). However, the user (or the user's application), could change the active SIP, if it wanted SIP input, and could then easily pop the SIP up or down at the right times (design goal #2 met). However, it turns out that none of the logical ways I tried to implement this SIP will cause this to happen. I've tried having the SIP return E_FAIL from its Select() method. This causes the SIP not to have a UI, but also seems to disable the other SIPs from doing anything. I've tried returning error codes from other methods, also. I've tried having the Showing() method call various of the APIs available to the SIP, asking that it be closed, but this doesn't work correctly (the frame window around the SIP is still displayed, although it has no client content). I've also done this for the Select() and other methods. Since I don't have source for the SOFTKB component, I'm out of ideas as to how to achieve my goals. Does anyone know of a DeviceIoControl() for the SOFTKB driver, other API function, a registry entry, or insider's trick that will allow me to either prevent the SIP from appearing, or cause it to immediately pop back down without disabling SIP input completely? Paul T. Tag: WTD: Win CE Platform Builder 2.11 Tag: 38793
  - 11
    - File system root on hard disk I have a cepc nk.bin built with the RAM and ROM file system and hive based registry storage on the Hard Disk that works great. I now want the root of the object store to be mounted to the hard disk so programs, shortcuts, etc. will be preserved though reboots. To do this I replaced the RAM/ROM file system with the ROM only file system from the catalog. I also changed the mountflags for HDProfile\FATFS to the following: [HKEY_LOCAL_MACHINE\System\StorageManager\Profiles\HDProfi le\FATFS] "EnableCacheWarm"=dword:0 "MountFlags"=dword:E I created the windows directory on my hard disk and copied all of the items from the release directory that appeared in the FILES section of my ce.bib. This boots successfully and runs with the following issues: The control panel is empty. File explorer is missing icons for some of its buttons. The start menu is empty past the first tier. Is there a section of files that I am failing to copy over, or a step that I am missing? Many of the shortcuts that are missing appear in initobj.dat is there something that needs to be done to that file? Is this the best way to go about this issue? I like the neatness of copying one file to upgrade the system instead of all the files listed in the files section like the RAM build, however cold boot retention is a must have. Tag: WTD: Win CE Platform Builder 2.11 Tag: 38777
  - 12
    - how to build a stand alone CEPC? - booted from Hard Disk? I followed the "How to ..." to build a CEPC booted from hard disk. Everything runs OK except the last step - Remove the boot floppy disk from the CEPC, restart the CEPC, and then verify that the OS image boots on the CEPC. The CEPC hanging there - 1 cursor blinks at the top left corner - forever! If I disable KITL and rebuilt after the change. I can find the nk.bin in RelDir\CEPC_X86Release. BUT, after download, no Release directory in CEPC. So I do not know where the nk.bin located and how to copy it to the hard disk? Tag: WTD: Win CE Platform Builder 2.11 Tag: 38770
  - 13
    - Error: failed PB timebomb check Hi, I try to do a rebuild all (and I did also rebuild all with enable deptree) and I got this error: makeimg: Check for F:\WINCE410\MIRANDA\ALTO_B~1 \RelDir\NATIONAL_GEODE_X86Debug\PreRomImage.bat to run. makeimg: run command: romimage F:\WINCE410\MIRANDA\ALTO_B~1 \RelDir\NATIONAL_GEODE_X86Debug\ce.bib Error: failed PB timebomb check makeimg: FATAL ERROR: Command returned non-zero exit code 1 (dec). makeimg: FATAL ERROR: Command returned non-zero exit code 1 (dec). Error PB2505: Error executing #(F:\WINCE410\MIRANDA\ALTO_B~1 \RelDir\NATIONAL_GEODE_X86Debug\)makeimg.exe. The platform builder I have is not an evaluation copy. I have a full license.... Any ideas why do I get PB timebomb check? Thanks!! Tag: WTD: Win CE Platform Builder 2.11 Tag: 38764
  - 14
    - NIC lost after reboot. I have implemented a hard reboot function like this in a aplication SetCleanRebootFlag(); KernelIoControl(IOCTL_HAL_REBOOT, NULL, 0, NULL, 0, NULL); This seems to reboot the CEPC fine, exept that the two network cards are not initialised. If I reboot by switching off and on everyting is ok. I use the CEPC with hive based registy on a x86 with IDE hard drive. The NIC uses the RTL8139 driver. Tag: WTD: Win CE Platform Builder 2.11 Tag: 38756
  - 15
    - Urgent - RDP protocol error in CE 4.1 Dear Greats, Already i posted one mail regarding the same below problem. We are using Windows CE Platform builder 4.1 with RDP builded. We are having ThinClient configuration. We leave the RDP connection for more than 9 minutes. Then the RDP session disconnects saying the Session is disconnected due to some protocol error. We have checked that any server side configuration is wrong. With the same server CE 4.0 client is working with our any problem. If their not inputs from Client side to Server side, session is getting closed. This is a big problem. I think, If their is not inputs (Keyboard / Mouse ) from client to server, that client side socket are some thing is getting closed. Is this a bug. can any one help me. This is very urgent. With regards, avkumar Tag: WTD: Win CE Platform Builder 2.11 Tag: 38748
  - 16
    - EARN$£$600\week downloading free software http://131695.PlugUsIn4Cash.com We know it sounds TOO good to BE true, but it?s REAL! Our International Technology firm will pay you hard cash each time FREE software is downloaded. Best of all you will only have to download ONE piece of software ONE time for FREE and you can be on your way to earning BIG! FIND OUT MORE BY VISITING http://StevenBrown1.PlugUsIn4Cash.com/ Tag: WTD: Win CE Platform Builder 2.11 Tag: 38746
  - 17
    - whether the wince surpport hard disk hi, I am using the pxa255 to develop my platform.Because I want to use the hard disk or CD-Rom as the input peripheral equipment, I am going to add a IDE controller to my hard platform, but I am wondering if the wince4.1 support the file format of hard disk or CD-Rom? If wince4.1 supports the function, how should I write the IDE controller driver,I mean what is the interface of the IDE driver MDD layer and PDD layer ,and if the file system of wince4.1 should be modify to adapt my requirment? Where can I find the driver example of wince4.1? thanks in advance an very much Tag: WTD: Win CE Platform Builder 2.11 Tag: 38741
  - 18
    - driver for data acqusition board on PCI bus works in debug kernel, but not in retail kernel Hi, I have successfully wrote and built a stream interface driver that interface with my data acq. board on the PCI of a CEPC. I have been doing all the work in debug version (the driver (dll) and the test program, and the OS). I was able to get everything working. Then I rebuilt the driver in retail mode. And I also built the release version of the kernel. Then when I run my test program, which subsequently tries to open my device using: CreateFile(TEXT("DAC1:"), GENERIC_READ|GENERIC_WRITE, 0, NULL, OPEN_EXISTING, 0, NULL); It failed. It gives me error code 55. I have attached the system monitor tool from eMVC, and I can see that DAC1 is one of the device on the system. I also put in debug messages in the DAC_Init() of my dll, and I can see that it gets called properly, and does all the IO and memory mapping properly. However, it seems like the problem is with CreateFile(), and somehow it thinks that the device does not exist on the system. Any help would be appreciated. Oh, btw, I'm relying on the PCIbus driver to load my board. It worked perfectly in the debug version. Just when I switch to retail version, it fails. Joseph Tag: WTD: Win CE Platform Builder 2.11 Tag: 38734
  - 19
    - CEPC on Secondary IDE Good day, The motherboard I have has a 40pin IDE interface for primary IDE Channel. I have a 44 pin IDE interface on the secondary IDE Channel. How do I configure the CE.Net image to recognize the secondary IDE as a Harddisk inorder for the user to store persistent data? Please advice Thanks Brandon Tag: WTD: Win CE Platform Builder 2.11 Tag: 38725
  - 20
    - Problem mapping physical address (0xC0000000) on Arm Integrator hi, I posted this message before (through google) but it's seem like it's appears only on google I can't see it using my newsreader so I repost it again here it's go : I have a device with memory registers in physical address 0xc0000000, for which I am porting a driver from Linux to CE 4.2 using PB. The device is connected to the logic module stack on an Arm Integrator board running ARM920T CPU. I have tried mapping this memory into virtual address using the following: .... addr = 0xc0000000; PHYSICAL_ADDRESS mapped, port = {addr, 0}; ULONG inIoSpace = 0; PUCHAR ioPortBase; if (!TransBusAddrToVirtual(Internal, 0, port, size, &inIoSpace, &mapped)) printf("Error translating I/O Ports.\r\n"); ... Debugging into TransBusAddrToVirtual showed that the debugger was disconnected inside the call for VitualCopy (in MmMapIoSpace). The Linux driver maps (by ioremap) and uses this address successfully. Does anyone know what could be causing this problem? I tried also to statically map this address by modifying OEMAddressTable (after finding out that CreateStaticMapping function isn't implemented on Arm), but couldn't access VA_TEST. ... VA_TEST EQU 0xa5000000 ;first availble after VA_SC_BASE EXPORT OEMAddressTable[DATA] OEMAddressTable ... DCD VA_TEST, 0xc0000000, 1 ... ; ; End of Table (MUST BE ZERO!) ; DCD 0, 0, 0 AFAIK, there is no need for static mapping, using TransBusAddrToVirtual should do the job for any user-mode driver. Any help will be appreciated, Ilya. Tag: WTD: Win CE Platform Builder 2.11 Tag: 38713
  - 21
    - Unexpected GPEBltparms I'll throw this out to see if anyone has comments. The two arrows use for forwards and backwards in the windows explorer generate 1bpp-source blts on my 16-bpp video driver. What tripped me up was that they generate a rop4 of 0xb8b8 which is PSDPxax but the brush pointer is NULL. I was thinking that checking the brush pointer for NULL would limit me to the rop4 codes that don't involve a brush, but evidently not. What is the assumed brush if one is not given as part of the GPEBltParms structure ? Tag: WTD: Win CE Platform Builder 2.11 Tag: 38705
  - 22
    - SOURCES Linker HI I have built a dll using the platform builder wizard (pbp file). Project-Settings then select the Link Tab, and in the box labeled Project Options I have the following commctrl.lib coredll.lib bcrapi.lib /nologo /base:"0x00100000" /stack:0x10000,0x1000 /entry:"_DllMainCRTStartup" /dll /incremental:no /pdb:"sa1100rel/BCRhandler.pdb" /debug /nodefaultlib:"$(CENoDefaultLib)" /out:"sa1100rel/BCRhandler.dll" /implib:"sa1100rel/BCRhandler.lib" /subsystem:$(CESubsystem) /align:"4096" /MACHINE:ARM /SECTION:shared,rws I can now build the same dll using Sources file. I can't figure out how to add /SECTION:shared,rws to my sources files, this is absoulutly necessary if the code is to work. I have tried adding the following to the sources but it doesn't have the desired affect CDEFINES= $(CDEFINES) /DBCRHANDLER_EXPORTS SECTION:shared,rws or CDEFINES= $(CDEFINES) /DBCRHANDLER_EXPORTS /DSECTION:shared,rws Regards Tariq Tag: WTD: Win CE Platform Builder 2.11 Tag: 38679
  - 23
    - SOURCES HI I have built a dll using the platform builder wizard (pbp file). Project-Settings then select the Link Tab, and in the box labeled Project Options I have the following commctrl.lib coredll.lib bcrapi.lib /nologo /base:"0x00100000" /stack:0x10000,0x1000 /entry:"_DllMainCRTStartup" /dll /incremental:no /pdb:"sa1100rel/BCRhandler.pdb" /debug /nodefaultlib:"$(CENoDefaultLib)" /out:"sa1100rel/BCRhandler.dll" /implib:"sa1100rel/BCRhandler.lib" /subsystem:$(CESubsystem) /align:"4096" /MACHINE:ARM /SECTION:shared,rws I can now build the same dll using Sources file. I can't figure out how to add /SECTION:shared,rws to my sources files, this is absoulutly necessary if the code is to work. I have tried adding the following to the sources but it doesn't have the desired affect CDEFINES= $(CDEFINES) /DBCRHANDLER_EXPORTS SECTION:shared,rws or CDEFINES= $(CDEFINES) /DBCRHANDLER_EXPORTS /DSECTION:shared,rws Regards Tariq Tag: WTD: Win CE Platform Builder 2.11 Tag: 38675
  - 24
    - DLL build problem hi all, I'm trying to make a DLL having a couple of methods and returning an integer value to my caller application. It should work in my Win CE.NET 4.2 device under ASP web pages. I haven't been able to make this work. Thus need help. First I used eVC++ 4.0 to create the DLL and downloaded it to my device, after which the LAN drivers mystically disappeared from my device and I was not able to test the ASP site. Additionally, the device hung after a few seconds. I also tried to reconstrct the DLL project in Platform Builder 4.2 by inserting a new empty DLL project and recreating the same files that I used in my eVC++ project. This however gave and error message like ... oleidl.idl Error PB2505: Error executing midl.exe. and I have no idea of how to fix this. It must have something to do with the .idl file, but dunno what. Please help me with one of my problems. Mike Tag: WTD: Win CE Platform Builder 2.11 Tag: 38665
  - 25
    - SOURCES Hi I am building a retail build, but it would be useful if I could modify the SOURCES file for one of the components to force it to build a debug version of itself. Is there any way I can do this. I have tried using the following CDEFINES= $(CDEFINES) -D_DEBUG in the sources file but it still builds a retail version of the dll. Any advice would be appreciated Regards Tariq Tag: WTD: Win CE Platform Builder 2.11 Tag: 38660

Folks,

I'm in search of copy of Windows CE Platform Builder 2.11 so that I
can create a modified version of ATADISK.DLL to support high capacity
Sony memory sticks on my HP Jornada 690, via a PCMCIA memory stick
reader.

Anyone know where I might be able to acquire this package for less
than something completely exhorbitant (given that this is a personal
project).

Please reply to this address.

Thanks,
Rob

Top

Re: Win CE Platform Builder 2.11 by Steve

Steve
Thu Jul 31 08:03:47 CDT 2003

It is not available anymore. Most people who have/had it upgraded to newer
versions and so can't just give/sell their old versions.

--
Steve Maillet (eMVP)
Entelechy Consulting
smaillet_AT_EntelechyConsulting_DOT_com

Top

Re: Win CE Platform Builder 2.11 by Chasidh

Chasidh
Thu Sep 11 16:01:47 CDT 2003

I also am looking for CEPB 2.11.

I have a completely new, legal (and worthless to me) CEPB
2.12 that I am able to include WITH ADDITIONAL PAYMENT for
an old CEPB 2.11 with or without later upgrade packages.

If you have no string of upgrades beyond CEPB 2.12, then
the upgrade license issue should be resolved.

Any takers? If yes, please, please reply to my email!

>-----Original Message-----
>It is not available anymore. Most people who have/had it
upgraded to newer
>versions and so can't just give/sell their old versions.
>
>--
>Steve Maillet (eMVP)
>Entelechy Consulting
>smaillet_AT_EntelechyConsulting_DOT_com
>
>
>.
>

Top