Localization

Tutorials Win: Microsoft Windows Forum

- Previous
  - 1
    - Copying bigger files from SD card is not happening Hi All I am using PB 4.2 I am using a 64MB Sandisk SD card (uses 8 bit CISC controller within the card I am not able to copy files above 13 MB from SD card to desktop using active sync In the receive part of code, we are checking status register to ensure data is ready in FIFO. Then, I am copying data from FIFO. The above operations(check status reg and copy from FIFO) happens in a loop until we copy everything (whole size). While file copy reaches 13 MB, status register gives "RECEIVE TIMEOUT" . The above issue happens with this particular card only I have one more Sandisk card (uses 32 bit RISC controller within the card). Using this card I can copy the files as big as possible. This is consistently happening Any solution Thank Prasanna Tag: Localization Tag: 50356
  - 2
    - why msn don't connect at WinCE net 4.2? When I try connect msn,my device display error "Signig in to.NET Messenger Service failed because the service is not compatible with this version of the program". Tag: Localization Tag: 50355
  - 3
    - PCMCIA with a CEPC Q1 Any recommended "off the shelf" cards for PCMCIA on a CEPC The cards typically come with WiFi network cards but none of the ones I have have the required chipset TI1250 (Texas Instaruments) or i82365-compatible (as in PB4.2 Q2 Looking at PCMCIA drivers on MSDN at http://msdn.microsoft.com/library/default.asp?url=/library/en-us/wceddk40/html/cxconPCCardDriverSupport.as There are drivers for 3 PCMCIA cards but when I look on the directory (Platform) there are no such subdirectories As file serach of %winceroor% finds nothing Tag: Localization Tag: 49349
  - 4
    - TDI support in Win CE 4.x? Hi all, I am planning to implement TDI based firewall in Windows CE 4.x. I have been trying to figure out if there are any support for TDI in Win CE. Until now I wasnt able to find any conclusive evidence of it. I'd appreciate if anyone can tell me. Moreover I shall be grateful if there is TDI support, if anybody can tell me where I can find references to the supported TDI Apis' for CE. thanks a lot in advanc Tarik Tag: Localization Tag: 49346
  - 5
    - About the Audio SoftwareMixer [HKEY_LOCAL_MACHINE\Audio\SoftwareMixer] "SampleRate"=dword:AC44 "Buffers"=dword:4 "BufferSize"=dword:800 "EnableLowPassFilter"=dword:1 "Priority 256"=dword:dc I found some difference between 'MediaPlayer' and 'PlaySound API'. I measured the analog audio output signals, playing the same .wav file by two ways. In MediaPlayer, the signal was smooth. But, in PlaySound API, it was like staircase. I guess the reason is LowPassFilter of SoftwareMixer. So, I changed the registry value "EnableLowPassFilter" is zero. As expected in MediaPlayer, the signal was not smooth and like staircase. I want to make the sound of PlaySound API is smooth. How can I use the 'PlaySound API' with Audio Software Mixer like MediaPlayer ? Please.. Tag: Localization Tag: 49344
  - 6
    - SDIO hardware attachment driver/software I am in process of designing a piece of hardware attachment to be used with an iPaq PocketPC through its SD slot. The hardware will follow SD IO specifications. I want this hardware to look as a bank of 4 8-bit read/write registers. Applications using this hardware control it by reading and writing these registers. An interrupt service routine will be a big plus. I really appreciate it if you can point me to the right direction. I have googled around and searched Microsoft site with not much success. Here are few questions if you enlighten me please. 1- Is it neccessary to write a driver to access this device? Is it possible for the application to use low level drivers already in the iPaq to access the SD slot without the need for a dedicated driver? 1- What is the appropriate software tool to create a driver to access a SD IO device attached to SD slot of an iPaq? 2- If Platform Builder is the right tool, where do you get it? In Microsoft site I can find articles mentioning the Platform Builder, but I cannot find a product named Platform Builder. Did they change the name? 3- Are there any articles or sample code showing SD IO access in a PocketPC? Thanks in advance Tag: Localization Tag: 49343
  - 7
    - can I distribute loadcepc with my NK.BIN? Are there licensing restrictions on distributing loadcepc with my NK.BIN My NK.BIN will reside on the boot parttion of a CEPC and I currently use loadcepc to load it. Should I be using some other loader Thanks Mik Tag: Localization Tag: 49337
  - 8
    - Windows CE ROM Image Builder Receiving these warning messages. How can I fix it or should I not worry about them. myIsr.dll is a loadable ISR ad mydriver.dll is of course, my CE Driver. Using old fixup style in module mydriver.dll Using old fixup style in module myIsr.dll John Tag: Localization Tag: 49336
  - 9
    - suspend doesn't work after RDP session Hi, I am running Win CE 4.2 on a SH3 device. There is button driver in the device. When click one of the button, the device will go to suspend. The code is like this keybd_event( VK_OFF, 0, KEYEVENTF_SILENT, 0 ); But if I run RDP, then clicking that button won't go to suspend. If I click Start on the bottom left of the device, then click suspend, it will work. It looks like if there is a RDP session, the virtual key VK_OFF doesn't work. Is there anyone know any information about this problem? By the way, it exists on Win CE 4.0 too. Thanks a lot Rosalind Tag: Localization Tag: 49332
  - 10
    - WinCe WebServer Hi, Can anyone tell me if there is/or where to get software to use a winCe based handheld wit intel Xscale proc as an Webserver Preferebly Php and stuf like that. Afz. Rudy Tag: Localization Tag: 49326
  - 11
    - Activesync via USB on a CEPC On an Intrynsyc XScale board, I can easily run activesync with development machine That board has a USB Client which allows it to connect to the development PC and run activesync How do you setup USB on a CEPC to activesync with a PC, given that they are both USB hosts? Tag: Localization Tag: 49316
  - 12
    - RAS Hi all I use Wince4.1 To use RAS, I use "COM1:". But, Dial-up Connection is not connected at RAS. In other word, threre is no dialtion Is it impossible to use COM1 for RAS Connection? I modified debug.c to not use debug port Plesase some advices Thanks Tag: Localization Tag: 49314
  - 13
    - BlueTooth driver in release and debug Hi all, I'm using the Mitsumi WML-C20 bluetooth controller with BCSP. This is working correctly in a debug image but not in a relase image. When I replace the btd.dll relase version in the release image with the btd.dll debug version the image works correctly. Any suggestions what might cause this problem and can also solve this (compiler optimisation problem....)? -- Jeroen Kratz Chess iT Tag: Localization Tag: 49313
  - 14
    - About Build Hi all, I use ce4.1 I tried to build(Build Selected features) "Standard Shell". But, Build is not completed The following is error message Error PB2504: Error spawning #(C:\WINCE410\private\wceshellfe\jupiter\Server\explorer\res)build.ex I modified "C:\WINCE410\PRIVATE\WCESHELLFE\JUPITER\SERVER\CESHELL\host2.cpp" I wonder that it is impossible to build "C:\WINCE410\PRIVATE\..." Thanks Tag: Localization Tag: 49312
  - 15
    - Keep-Alive Hi all, I want to implement the Keep-Alive functionality on a Thin Client device connected to a Terminal Server. As I know it is a standard feature of the TCPIP protocol (there're also registry settings for it), but it is disabled by default. Does someone know how to make it work? Must be enabled by a custom application? How? Thank you in advance, Gabor Varga Tag: Localization Tag: 49311
  - 16
    - what is the mean of instruction "MRA"MAR" This is a multi-part message in MIME format. ------=_NextPart_000_0007_01C402C2.7E1F0690 Content-Type: text/plain; charset="gb2312" Content-Transfer-Encoding: quoted-printable =BF=D5=B0=D7hi,all h:\wince410\platform\intel_dbpxa250\kernel\hal\ARM\cpregxsc1.s(291) = warning : A0241: Instruction mra not supported for -cpu "-arch 4t" h:\wince410\platform\intel_dbpxa250\kernel\hal\ARM\cpregxsc1.s(331) = warning : A0241: Instruction mar not supported for -cpu "-arch 4t" ------=_NextPart_000_0007_01C402C2.7E1F0690 Content-Type: text/html; charset="gb2312" Content-Transfer-Encoding: quoted-printable <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN"> <HTML><HEAD><TITLE id=3DridTitle>=BF=D5=B0=D7</TITLE><BASE=20 href=3D"file://C:\Program Files\Common Files\Microsoft = Shared\Stationery\"> <META http-equiv=3DContent-Type content=3D"text/html; charset=3Dgb2312"> <STYLE>BODY { MARGIN-TOP: 25px; FONT-SIZE: 10pt; MARGIN-LEFT: 25px; COLOR: #000000; = FONT-FAMILY: =CB=CE=CC=E5, =BA=DA=CC=E5 } P.msoNormal { MARGIN-TOP: 0px; FONT-SIZE: 10pt; MARGIN-LEFT: 0px; COLOR: #ffffcc; = FONT-FAMILY: =BA=DA=CC=E5, "=CB=CE=CC=E5" } LI.msoNormal { MARGIN-TOP: 0px; FONT-SIZE: 10pt; MARGIN-LEFT: 0px; COLOR: #ffffcc; = FONT-FAMILY: =BA=DA=CC=E5, "=CB=CE=CC=E5" } </STYLE> <META content=3D"MSHTML 6.00.2800.1400" name=3DGENERATOR></HEAD> <BODY id=3DridBody bgColor=3D#ffffff background=3D"Blank Bkgrd.gif"> <DIV>hi,all</DIV> <P>h:\wince410\platform\intel_dbpxa250\kernel\hal\ARM\cpregxsc1.s(291) = warning :=20 A0241: Instruction mra not supported for -cpu "-arch=20 4t"<BR>h:\wince410\platform\intel_dbpxa250\kernel\hal\ARM\cpregxsc1.s(331= )=20 warning : A0241: Instruction mar not supported for -cpu "-arch=20 4t"<BR></P></BODY></HTML> ------=_NextPart_000_0007_01C402C2.7E1F0690-- Tag: Localization Tag: 49308
  - 17
    - Btpair.exe relies on BTHLINK sample?? This is a multi-part message in MIME format. ------=_NextPart_000_002F_01C40227.178C0950 Content-Type: text/plain; charset="Windows-1252" Content-Transfer-Encoding: quoted-printable Hello, The help file of platform builder said: "The compiled sample generates a Btpair.exe application. It relies on = the BTHLINK sample device driver that needs to be compiled and copied to = the device." However, I can compile the Btpair project without linking Bthlink.lib, = and I did not find btpair.c call any function related to Bthlink(for = example RegisterDevice(L"BTL", 1, "bthlink.dll", NULL) that is mentioned = in help file). Could anybody explain it? If need I modify the sample = code? --=20 Thanks!! Gordon ------=_NextPart_000_002F_01C40227.178C0950 Content-Type: text/html; charset="Windows-1252" Content-Transfer-Encoding: quoted-printable <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN"> <HTML><HEAD> <META http-equiv=3DContent-Type content=3D"text/html; = charset=3Dwindows-1252"> <META content=3D"MSHTML 6.00.2737.800" name=3DGENERATOR> <STYLE></STYLE> </HEAD> <BODY> <DIV><FONT face=3DArial size=3D2>Hello,</FONT></DIV> <DIV><FONT face=3DArial size=3D2></FONT> </DIV> <DIV><FONT face=3DArial size=3D2>The help file of platform builder=20 said:</FONT></DIV> <DIV><FONT face=3DArial size=3D2></FONT> </DIV> <DIV><FONT face=3DArial size=3D2>"The compiled sample generates a = Btpair.exe=20 application. It relies on the BTHLINK sample device driver that needs to = be=20 compiled and copied to the device."</FONT></DIV> <DIV><FONT face=3DArial size=3D2></FONT> </DIV> <DIV><FONT face=3DArial size=3D2>However, I can compile the Btpair=20 project without linking Bthlink.lib, and I did not find btpair.c = call any=20 function related to Bthlink(for example RegisterDevice(L"BTL", 1,=20 "bthlink.dll", NULL) that is mentioned in help file). Could=20 anybody explain it? If need I modify the sample code?</FONT></DIV> <DIV><BR><FONT face=3DArial size=3D2>-- <BR></DIV></FONT> <DIV><FONT face=3DArial size=3D2></FONT> </DIV> <DIV><FONT face=3DArial size=3D2>Thanks!!<BR>Gordon</FONT></DIV> <DIV><FONT face=3DArial size=3D2></FONT> </DIV></BODY></HTML> ------=_NextPart_000_002F_01C40227.178C0950-- Tag: Localization Tag: 49307
  - 18
    - PCI interrupt sharing Hi all, I'm porting on a pretty standard PCI device driver for CE 4.2, that originated in 2.12 or sometime back then. Currently, the driver uses InitializeInterrupt() to set up being notified of interrupts. It requests a SYSINTR_ value as the OEM index plus the IRQ number. Obviously, this fails if there are multiple devices that have the same IRQ. I see that the PCI bus requests a unique SYSINTR from the kernel and provides it in the registry. Will it be sufficient to use that value? What if other devices also use the same IRQ, perhaps a NIC that I don't have the sources of? Much of the documentation implies that to share interrupts, it is necessary to rely on installable ISR handlers, such as GIISR.dll. I can't tell whether I really need to worry about this or not. My quick glance says the source appears to do nothing but clear the interrupt, and not call notify my driver that it ever happened. So my questions are: Do I have to load an installable ISR within my PCI driver? Or does the PCI bus driver handle that for me? Or is it not related? If an installable ISR is needed, do I still use InitializeInterrupt() to associate an event with the unique SYSINTR? Thanks for any help and clarifications, -E. Nelson Tag: Localization Tag: 49302
  - 19
    - CETK clientside.exe fails Hi, I am trying to get the Windows CE Test Kit working but to no avail. I have my host PC connected to the target over ethernet. I used ethernet boot to download the image. I have added the Windows CE test Kit to the Features list. Platform builder and the Windows CE test Kit are running on the host PC. Then from the CE shell I have entered the command s clientside.exe /i=aaa.bbb.ccc.ddd /p=5555 The debug message warns that "AUTORAS:: Reg does not contain RasEntry value!!!", I checked autoras.c, the error message shows that autodial cannot find the phonebook entry in [HKLM\Comm\AutoRas\RasEntry]. Do I have to add this registry entry to make it work and how to add that? Thank you so much! Alex 2548278 PID:da5de23e TID:da359526 0x9a311618: RELFSD: Opening file clientside.exe from desktop 2548921 PID:da37464a TID:da359526 0x9a311618: InitSharedHeap: 46000000 0 c 2548922 PID:da37464a TID:da359526 0x9a311618: InitSharedHeap: return 46000050 2548926 PID:da37464a TID:da359526 0x9a311618: >>> Loading module clientside.exe at address 0x10010000-0x10020000 Loaded 'D:\WINCE420\PUBLIC\WPC\RELDIR\BVDMAIN-ARMV4IDEBUG\CLIENTSIDE.EXE', no matching symbolic information found. 2548960 PID:da5de23e TID:da359526 0x9a311618: RELFSD: Opening file wcetk.txt from desktop 2549124 PID:7a4108e6 TID:ba3ddfb6 0x9a3bb400: WINDOWCREATED: 0 2549256 PID:3a5b2276 TID:da359526 0x9a311618: AUTORAS:: Reg does not contain RasEntry value!!! 2549257 PID:3a5b2276 TID:da359526 0x9a311618: AUTORAS:: ARSDecideDial() returns: [DO NOT DIAL] 2549257 PID:3a5b2276 TID:da359526 0x9a311618: AUTORAS:: Not dialing.. 2549259 PID:3a5b2276 TID:da359526 0x9a311618: AUTORAS:: IOCTL_ARS_DIAL returns [Succesfully] 2549261 PID:da37464a TID:da359526 Internal Clientside error while trying to connect to the server. Clientside will now exit Tag: Localization Tag: 49301
  - 20
    - RAS to Linux I'm still having PPP troubles.. I manage to get the my CE target device to go through the initialization of a PPP connection with a Linux box (although I still cant connect via serial to work on my Windows 2000!)... however after the targets assigned IP address is sent to it, and it acks this IP address the Win CE device claims it gets disconnected... but the linux box still thinks the connection is going! Any idea Thanks Tag: Localization Tag: 49300
  - 21
    - RNDIS/UDC XSC1BD driver Hi All, I have managed to link and include the common RNDIS MDD driver with my PXA255 UDC PDD Driver but I seem to be getting errors. I'm assuming (because of previous posts) that this is due to the IOCTL_HAL_TRANSLATE_IRQ condition not being implemented in the XSC1BD BSP. When I check my debug log (after I get a first time exception) is: 4294769168 PID:81c6a782 TID:81c8ef7a 0x81c6a198: RndisMini: IRQ -> SYSINTR translation failed 4294769171 PID:81c6a782 TID:81c8ef7a 0x81c6a198: <<< Unloading module xsc_udc_rndis.dll at address 0x01DD0000- 0x01DE7000 I have read in previous posts that I can specify the Sysinterrupt in platform.reg like this: [HKEY_LOCAL_MACHINE\Comm\RndisMini1\Parms] "BusNumber"=dword:0 "BusType"=dword:0 "Sysintr"=dword:30 I use the number thirty cause that is the value that SYSINTR_USB_CLIENT resolves to: #define SYSINTR_USB_CLIENT (SYSINTR_FIRMWARE+14) But I still get the same error. Do I have to implement IOCTL_HAL_TRANSLATE_IRQ (OEMTranslateIrq) or have I misunderstood the value of "Sysintr" in my registry? Cheers, Andrew Tag: Localization Tag: 49299
  - 22
    - FlushDCache CE4.2 use OEMCacheRangeFlush to replace FlushDCache, FlushICache in CE 4.0 I saw there is this funciton which has been implemented in \WINCEROOT\publiccommon\oaks\csp directory by Microsoft, so I did nothing. but when I compile the Windows CE OAL in CE 4.2, still got the following message error LNK2019: unresolved external symbol OEMCacheRangeFlush referenced in function KernelFindMemor error LNK2001: unresolved external symbol OEMCacheRangeFlus Why is that Tag: Localization Tag: 49298
  - 23
    - debug serial port Hi I have an application that uses 2 serial ports on a PXA255(BTUART and FFUART) under WinCE4.10. I now have a need to convert the FFUART back to a debug port to spit out some debug messages. The only way I can get the system to boot up with the debug port functioning is to remove the serial driver which sets BSP_NOSERIAL=1. If I do this, however, my application cannot use the BTUART. Is there a way to have one serial port as a debug port and the other available to my application simultaneously? Currently I can only do one or the other Thanks Don Tag: Localization Tag: 49297
  - 24
    - What Happened to the QFEs??? Am I missing something, or did the CE.NET QFEs get removed from the downloads area of the MS web site? The only ones I can find are some old quarterly QFEs on the regular embedded site - nothing newer than Q3 of last year. This info is at http://www.msdn.microsoft.com/embedded/downloads/ce.net/wince/default.aspx There's now a reference to the OEM Embedded site, which is restricted and requires registration. Are the QFEs no longer publicly available? -- Dean Ramsier - eMVP Accelent Systems http://www.accelent.com Tag: Localization Tag: 49295
  - 25
    - remove drivers from cloned BSP Hi, What's the best way to remove a driver from a platform? From the FeatureView, I can't simply delete the driver, it's just come back. I tried deleting it from the cloned .cec file(that created the platform/project) first, then goback to PB, then seems to be able to do it. Is this safe; the correct way to do it. (assume I decided that I don't needed that driver after I have cloned it and used it for a while;for the next prototype) Is this how the cloning process work when it ask what driver you want to want in the cloned BSP? Tag: Localization Tag: 49293
- Next
  - 1
    - Re: PCMCIA with PCI card on CEPC Chris, Did you able to make it work ? I have same problem now. > Date: Thu, 17 Apr 2003 14:56:18 -0500 > From: Chris Edgington > Subject: Re: PCMCIA with PCI card on CEPC > > Figured it out .... examining the TI1250.reg file reveals that my Ricoh > chipset's PCI device ID is 0x0475, whereas the .reg file is looking for > 0x0476. Hopefully I can get my device to work, even though its an > earlier rev. Changing the reg file results in the being pcmcia.dll > loaded, and I can now set breakpoints and see debug messages from it. > > Thanks for reading and responding to my messages. > > Later, > -Chris > Tag: Localization Tag: 49291
  - 2
    - Serial port This is a multi-part message in MIME format. ------=_NextPart_000_0034_01C401F9.98459D00 Content-Type: multipart/alternative; boundary="----=_NextPart_001_0035_01C401F9.98459D00" ------=_NextPart_001_0035_01C401F9.98459D00 Content-Type: text/plain; charset="Windows-1252" Content-Transfer-Encoding: quoted-printable BlankMy CEPC only has 1 COM port and I use PB4.2. I made a program send = data to COM1, but nothing send to COM1. But if I open "System" under control panel, something send to COM1. I added "Serial port support" to platform. Is there anything I need to = take care of, like platform setting.... Thanks so much! ------=_NextPart_001_0035_01C401F9.98459D00 Content-Type: text/html; charset="Windows-1252" Content-Transfer-Encoding: quoted-printable <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN"> <HTML><HEAD><TITLE id=3DridTitle>Blank</TITLE> <META http-equiv=3DContent-Type content=3D"text/html; = charset=3Dwindows-1252"><BASE=20 href=3D"file://C:\Program Files\Common Files\Microsoft = Shared\Stationery\"> <STYLE>BODY { MARGIN-TOP: 25px; FONT-SIZE: 10pt; MARGIN-LEFT: 25px; COLOR: #000000; = FONT-FAMILY: Arial, Helvetica } P.msoNormal { MARGIN-TOP: 0px; FONT-SIZE: 10pt; MARGIN-LEFT: 0px; COLOR: #ffffcc; = FONT-FAMILY: Helvetica, "Times New Roman" } LI.msoNormal { MARGIN-TOP: 0px; FONT-SIZE: 10pt; MARGIN-LEFT: 0px; COLOR: #ffffcc; = FONT-FAMILY: Helvetica, "Times New Roman" } </STYLE> <META content=3D"MSHTML 6.00.2800.1106" name=3DGENERATOR></HEAD> <BODY id=3DridBody style=3D"COLOR: #000080; FONT-FAMILY: Verdana" = bgColor=3D#ffffff=20 background=3Dcid:002f01c40223$81127d40$74bf2cd8@3ComC> <DIV>My CEPC only has 1 COM port and I use PB4.2. I made a program send = data to=20 COM1, but nothing send to COM1.</DIV> <DIV>But if I open "System" under control panel, something send to = COM1.</DIV> <DIV> </DIV> <DIV>I added "Serial port support" to platform. Is there anything I need = to take=20 care of, like platform setting....</DIV> <DIV> </DIV> <DIV>Thanks so much!</DIV> <DIV> </DIV> <DIV> </DIV> <DIV> </DIV> <P> </P></BODY></HTML> ------=_NextPart_001_0035_01C401F9.98459D00-- ------=_NextPart_000_0034_01C401F9.98459D00 Content-Type: image/gif; name="Blank Bkgrd.gif" Content-Transfer-Encoding: base64 Content-ID: <002f01c40223$81127d40$74bf2cd8@3ComC> R0lGODlhLQAtAID/AP////f39ywAAAAALQAtAEACcAxup8vtvxKQsFon6d02898pGkgiYoCm6sq2 7iqWcmzOsmeXeA7uPJd5CYdD2g9oPF58ygqz+XhCG9JpJGmlYrPXGlfr/Yo/VW45e7amp2tou/lW xo/zX513z+Vt+1n/tiX2pxP4NUhy2FM4xtjIUQAAOw== ------=_NextPart_000_0034_01C401F9.98459D00-- Tag: Localization Tag: 49290
  - 3
    - Setting baud rate prior to RasDial. I'm trying to change a unimodem serial port baud rate prior to calling RasDial on my Windows CE .NET 4.1 device. I am successfully setting the baud rate when the line is configured with the RAS server, but now I am working on improving dial out capabilities. Below is code that I am trying from which I am trying to set the baud rate. I removed some comments and error checking/handling. All of these API calls succeed without error! I'm afraid my changes aren't being applied because I'm specifying the modem line to use by device name rather than a line handle. My code that configures the RAS server uses RasIOControl with the RASCNTL_SERVER_SET_PARAMETERS flag to change the device configuration, I'm wondering if I have to do something similar prior to calling RasDial rather than using lineSetDevConfig. lineGetDevConfig(dwDeviceID, pVSDevCfg, L"comm/datamodem"); UCD.dwCommand = UNIMDM_CMD_CHG_DEVCFG; UCD.lpszDeviceClass = L"comm/datamodem"; UCD.lpDevConfig = pVSDevCfg; UCD.dwOption = UNIMDM_OPT_BAUDRATE; UCD.dwValue = dwBitsPerSecond; rc = lineDevSpecific(hLine, 0, NULL, &UCD, sizeof(UCD)); lineGetMessage(hLineApp, &LineMessage, INFINITE); dwResult = lineSetDevConfig(dwDeviceID, (PBYTE)pVSDevCfg + pVSDevCfg->dwStringOffset, pVSDevCfg->dwStringSize, L"comm/datamodem"); Please let me know if you have any ideas. Thanks, George McCollister Tag: Localization Tag: 49288
  - 4
    - XIP vs RAM Thanks for the info Dean. I copied to responses to a new discussion thread as the subject title really did not apply. Would like some more input if anyone else who would like to chime in. I would think a biggey would be $$. Not having the OS in RAM would save megabytes (my images are approaching 25Meg) this is now freeed for scratch. Maybe the system can even get away with the next small size RAM ($$). Does anyone know if/what the premimum of the "K" Strata FLASH is? I would think the XIP OS would also be inherently more stable as it's exicuting from Read Only Memory, therefor there is less of a chance the OS could self destruct itsself?? Also what are the steps needed to transition to a XIP OS? I know the bootloader would need some work. Is it a simple matter of checking the "Enable image for flash" ??? See inline... -- Dean Ramsier - eMVP Accelent Systems http://www.accelent.com "A. User" <dve@byby.com> wrote in message news:u00PCkeAEHA.2480@TK2MSFTNGP11.phx.gbl... > I am very interested in Dean's comments. > > I was under the impression there was quite a difference between executing > from Flash as opposed to RAM. Do you have any numbers? > > I would like to see a comparison ... something like this: > feel free to expand and/or correct me where needed. > All opinions welcome > > FLASH (XIP) > Slower execution Yes, Flash is slower than RAM, no question. However, the impact can be minimized by making use of high performance features in flash. For example, using the burst mode of regular J3 strataflash is much faster than standard access. If you switch over to using synchronous strataflash (K3) it's very fast. Approaches the performance of running from RAM. Other techniques include compressing modules that impact performance. This causes them to be decompressed and run from RAM. Careful tuning of the system this way can do wonders. > Saves RAM, system needs less RAM as RAM is only needed for stack,heap, > variables etc. and not OS > bootup time faster. > harder to setup (?) Not sure where this comes from, booting from XIP flash is the simplest thing possible. There are no extra steps to be concerned about - just get the image into flash and you're done. > harder to do OS Flash upgrades If you're upgrading from within the OS, yes. It's very challenging to upgrade flash when you're executing from it, for several reasons. This is why most solutions rely on the bootloader to do upgrades. This can be a shared task with the OS if desired and there's enough RAM available. > does (not) work with debugger (??) You can't step through code if it's in flash (the debugger can't set breakpoints in ROM). Other aspects of the debugger do work. You can get around this by loading the image into RAM when doing debugging. You can also set the C flag to compress the module you're interested in. That will cause the module to be loaded into RAM, where it can be debugged. > does (not) work with emulators (??) Don't know how this applies. Why be concerned about where the image is stored if you're running from an emulator? > > RAM > traditional build > faster > on line FLASH OS upgrades easer as OS is in RAM > > > I know some are subjective any other pros/cons you can think of ? > > > > "Dean Ramsier" <dramsiernospam@accelentnospam.com> wrote in message > news:eMdf4mSAEHA.2348@TK2MSFTNGP09.phx.gbl... > > Since you're using BinFS and not attempting to XIP from strataflash (a > > questionable decision in my opinion) you should be able to use the NOR > flash > > driver available in PB. In fact, since BinFS is already running, the > block > > driver is apparently already there. All you need to do is get the > registry > > settings correct to format/partition/mount the remaining part of the > flash. > > The hive registry can then be targeted to that file system. This can all > > happen automatically. > > > > Why are you choosing to use BinFS instead of executing directly from > flash? > > It's much more complicated, and comes with performance penalties over > > executing directly in place. The only advantage is that SDRAM is faster > > than J3 flash, but paging code in and out will negate much or all of that > > advantage. It also costs you RAM space. BinFS is primarily intended for > > devices where the image is stored on a media that doesn't support XIP, > NAND > > flash. > > > > -- > > Dean Ramsier - eMVP > > Accelent Systems > > http://www.accelent.com > > > > ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ > > Have an opinion on the effectiveness of Microsoft Embedded newsgroups? > Tell > > Microsoft! > > https://www.windowsembeddedeval.com/community/newsgroups > > ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ > > > > > > "Fabio - ElettronicaGF" <fmelandri@elettronicagf.it> wrote in message > > news:3ad3b9c6.0403030250.684fbadf@posting.google.com... > > > Hi all, > > > I'm a newbie in WCE.NET and Platform Builder 4.2 and i'm trying to > > > understand how to use my on-board flash for the OS image and > > > data/registry storaging. > > > My platform is a pxa255 processor board with 32M strata flash (2 x > > > 28f128j3a) and 64M sdram. > > > My bootloader create a BINFS partition and an EXTENDED partition on > > > the rest of the flash memory. > > > The BINFS partition serves for the OS image (non-XIP mode). > > > Is it possible to use the EXT partition for persistent storage and > > > hive based registry ? > > > Do I need for something like Intel IPSM or the NOR strata flash driver > > > (from PB) and some registry settings (as I see in PB Help) are enough? > > > Do I have to modify my bootloader to create a FAT partition instead of > > > an EXTENDED? > > > Now, when my platform boot, I can see (with stguil) only a BINFS > > > partition. > > > I would like to have the storage/registry partition automatically > > > created at boot time, is it possible? > > > > > > > > > Thanks in advance, > > > best regards. > > > > > > Fabio Melandri > > > ElettronicaGF > > > > > > Tag: Localization Tag: 49286
  - 5
    - file system filter driver not loading in I MATE Smart Phone 2003 device ? Hi I developed a file system filter driver for SmartPhone 2003 device I have I mate smartphone 2003 device. I am using this filter driver for StorageCards. When I try to run my filter driver in emulator using ramdisk block driver it works fine. but when i try to use in imate smartphone 2003 device its not loading into filesys.exe process. I registried my file system filter driver under FAT file system. so when ever StorageCard inserts into device fatfs will load into filesys.exe and also filter drivers. I verified signing also, still the problem is same. can any body help me. regards chakka sudhakar Tag: Localization Tag: 49282
  - 6
    - DHCP, VBridge and Non-debug TCP/IP Communication I'm using PB4.2 to create a BSP for a custom headless device. At the moment I have an Ethernet bootloader and an OAL that I think is nearly complete (foolish thing to say!). I use KITL over the Ethernet, with VBridge and VMini to share the Ethernet connection. I've added the code for VBridge/VMini as described in the PB Help, and I've also added the registry entries, which I can see on the target using the Remote Registry Editor. I compile the OAL code with -DIMGSHAREETH in the compiler options defined in the sources file. The Communication Services features I have in my test platform are: Networking Features: NDIS 5.1 Network Utilities TCP/IP Winsock Support Servers: Core Server Support Web Server (HTTPD) The following environment variables are defined for the BSP in the Platform Settings: BSP_NOCOMCARD 1 BSP_NOPCMCIA 1 BSP_NOSERIAL 1 BSP_NOSTORAGE 1 BSP_NOUSBSER 1 When I build the system with the IP address hard-wired (and defined in the registry) it all works fine. The network utilities work, and the target responds to ping and http requests from other machines. The problem is, when I build it to use DHCP, non-debugging TCP/IP packets are apparently not handled correctly. For example, if I ping the target from another machine, the ping requests time out. Also, the network utilities on the target don't work - ping fails, and ipconfig reports that the IP address and subnet mask are both 0.0.0.0. By adding code to output debug info, I found that when I ping the target from another machine, the packets sent by ping are correctly handled by VBridgeKIndicateOneRxBuffer, i.e. they are taken by VMini, but then they seem to get lost after that. Do you know what might be missing, or else not working? Currently I don't have any code in the OAL to put the IP address obtained from DHCP in the registry - should the OAL be doing this, or does something in the kernel take care of that? Regards, Douglas Wilson Tag: Localization Tag: 49273
  - 7
    - Can I have two FlashFx disks at the same time ? I have two separate flash banks, located at different addresses. I can mount a flash disk one at a time, but not both at the same time The second instance failes. If I disables the first instance, the second instance succeedes Is there a limitation in the FlashFx driver that prevents me from having two flash disk ? ; HIVE BOOT SECTIO [HKEY_LOCAL_MACHINE\Drivers\BuiltIn\FlashFX "DLL"="FlashFX.DLL "FSD"="FATFSD.DLL "Prefix"="DSK "Ioctl"=dword: "Order"=dword: "Index"=dword: "Flags"=dword:100 "Start"=dword:180000 "Length"=dword:080000 "IClass"="{A4E7EDDA-E575-4252-9D6B-4195D48BB865} "ProfileName"="FlashFXDisk1Profile [HKEY_LOCAL_MACHINE\System\StorageManager\Profiles\FlashFXDisk1Profile "AutoMount"=dword: "AutoPart"=dword: "AutoFormat"=dword: "MountFlags"=dword: "Name"="Datalight FlashFX "Folder"="FlashFX Disk "DefaultFileSystem"="FATFS "PartitionDriver"="mspart.dll ; END HIVE BOOT SECTIO [HKEY_LOCAL_MACHINE\Drivers\BuiltIn\FlashFX1 "DLL"="FlashFX.DLL "FSD"="FATFSD.DLL "Prefix"="DSK "Ioctl"=dword: "Order"=dword: "Index"=dword: "Start" =dword:0800000 "Length"=dword:0080000 "IClass"="{A4E7EDDA-E575-4252-9D6B-4195D48BB865} "ProfileName"="FlashFXDisk2Profile [HKEY_LOCAL_MACHINE\System\StorageManager\Profiles\FlashFXDisk2Profile "AutoMount"=dword: "AutoPart"=dword: "AutoFormat"=dword: "MountFlags"=dword: "Name"="Datalight FlashFX2 "Folder"="LoopDisk "DefaultFileSystem"="FATFS "PartitionDriver"="mspart.dll Tag: Localization Tag: 49269
  - 8
    - italian keyboard layout Hi, now I need to load the italian keyboard layout in my project in platform builder 4.2. I think I must put a registry entry like this one in project.reg but I don't know the italian id: [HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\KEYBD] "Keyboard Layout"="00000409" Is it correct ? What is the italian id ? I hope I don't have to create all the language package in C:\WINCE420\PUBLIC\COMMON\OAK\DRIVERS\KEYBD\DEVICELAYOUTS\PS2_AT... Then if I go in the Menu, Platform, Settings and click on Locale I have all the Locales regional settings including italian and I have italian as default setting but above in the codepages I don't have any italian record, just some latin.... This is confusing me a lot .... Thanks Carlo Tag: Localization Tag: 49268
  - 9
    - About RAS Hi all I use WinCE 4.1 and Rockwell modem. And I am tryng to connect RAS Server The point of problem is no dialtone I tried to connect RAS server as the following Make New Connent -> Dial-Up Connection -> "Hayes Compatible on COM1:" -> Phone number:145 -> Finish, and "Connect The following is connection result Opening Port -> Dialing "145" -> messagebox lanuc (Message: Threre is no dialtone. Make sure your modem is connected to the phone line properly I already had connected the phone lline properly For your reference, I had modified "debug.c" to use COM1 as UART(in other word, It disable COM1 as debug port) But, when I use "Manual Dial", I can listen to dialing tone I don't know why no dialtone If you allow, would you like to give me some info about thie issue Thanks Tag: Localization Tag: 49264
  - 10
    - Auto hiding Cursor Hi , I want that my cursor should not appear on my screen for that i set BSP_NOCURSOR = 1 but still the cursor is appearing on my screen. I did this by the following way Right Click -> Settings From Setting select the Environment Tab select New In Variable Name : BSP_NOCURSOR Variable Value : 1 Is anything wrong with the above procedure if so then please help me. Regards Purohit. Tag: Localization Tag: 49263
  - 11
    - Application Download Issue hi All i am in bit fix and there are couple of issues regarding application porting I am created a Windows Thin Client inage using the PB 4 and successfully downloaded to m CEPC it downloads properly and also shows the WBT wizard.i am Using Ethernet Connectio for OS Image Downloading After Downloading since the platform Builder shows all the Target Control target messages and debugger connected and i could see that Symbols being Loaded one after the Other.. the Issues ar 1) After i see the WBT Wizard i Complete it and i give my development workstation as server and some user name the Windows think Client Doesnt Connects. the only other Option is SHutdown...wat could be the issue My Development machine is a Windows 2k and we are on Workgroup with No domain Controller.So everytime the remote Desktop Client Comes i am Stuck as to go where after that .I want to get the CE desktop running Since after download the Image goes to the RAM so its not sustaining any changes i am making on the thin Client and i cant get a some flash chip I have assigned a IP to CEPC which is 10.20.1.60 and my development workstation IP is 10.20.1.6.even though the IMage download happens properly i cant ping my CEPC from th Workstation wat could be issue regarding this 2) the second issue is I am have created application in EVC 4.0 and once i download the OS image from the PB 4 and the WBT wizard Appears i try to Connect EVC USing KITL/CES option from the SDK. but it says Failed to Connect to device Although the PB is connected already and as i read from the Newsgroup items once the PB gets connected and u can see debug messages the EVC should connect but its not i tried the TCP/ip connection also but to no avail I have also got a NULL modem Cable connected on the COM ports and i have cheked thje cable its working fine. SO evc is not connecting to the CEPC if any one give some replies to the above issues it would be really gr thjanx in advanc Vish Tag: Localization Tag: 49262
  - 12
    - can anyone give me some clue about use xip in smdk2410 hi,every. Thanks for your attention. I want to use xip feather in smdk2410,with pb 4.2,can any one help me give me some clue about it? Thanks Tag: Localization Tag: 49261
  - 13
    - How to change suspend/resume procedure Hi We know when entering suspend mode, the system will invoke OEMPoweroff(), it will call gwes, wdevice, an device power management funcions in turn , when resume the system it will inverse the procedure. I want to chang some device drivers power management functons' calling procedure, for example, if entering suspend mode, system will call PCMCIA power management function, then call audio's, now I want to inverse the procedure Could you help me Regard -Weijie Zh Tag: Localization Tag: 49258
  - 14
    - VBridge/Vmini problem Hi, I'm building a platform (release version) for a VIA Twister and it seems to fail on the VBridge/VMini. The output below indicates that the kernel is looking for a NE2000 (altough NE2000 support was not added to the platform). I get the impression that the whole thing fails because of the NE2000 that is not found, which might trigger the 'VB_INITIALIZED returns [0]', which seems to trigger the VMini problem. Anyone encountered something like this before ?? Thanx!, all help is appreciated Mike ************ OUTPUT ************ Debug Serial InitWInit failed SysInit: GDTBase=8095c0d0 IDTBase=80989d00 KData=80999800 Windows CE Kernel for i486 Built on Jul 25 2003 at 11:51:18 g_PageDir = 8099b000 +OEMKitlInit Ethernet Type 2 +EDBG:NE2000Init EDBG:NE2000Init using I/O range at 0x00000000 EDBG:NE2000Init:HWInit failed to read cmd reg -EDBG:NE2000Init Unable to initialize KITL Transports! -OEMKitlInit KITL Initialization Failed, No debugging support available Find VIA USB Device VIA USB IoBase 1800 [VIABSP] BSP version: 1.31, Mar 3 2004, 21:55:39 RTC - Status Reg B - 0x02 X86Init done, OEMAddressTable = 80208238. VBridge:: VB_INITIALIZED returns [0] VMini:: VBridge is not initialized! Bail out.. Explorer(V2.0) taskbar thread started. Explorer(V2.0) using old style message pump. NDISPWR:: Found adapter [PCI\DP838151] Tag: Localization Tag: 49256
  - 15
    - Exporting function from an .exe to be used by loaded .dll I have the following design. Build host appname.exe that exports some useful functions. When I compile this, appname.lib is created with the exported files. Create plugin dlls that link with appname.lib and are loaded at run time by the host appname.exe using LoadLibrary(plugin_name). These plugins can use all the functions exported by appname.exe. I have this design coded and working flawlessly on Windows XP. Using the same code base I then created my CE.net version in EVC4. When I run appname.exe on CE (in the emulator - no hardware yet) the plugins do not load and GetLastError() returns 193 - Bad EXE Format. I can't figure out why this is happening. As a test I created a simple .exe and simple .dll in EVC4. The exe exports one function and the dll uses it. The dll load failed with the same error but as soon as I remove the exported function from the exe and its reference from the dll it loads fine. This design is critical to my application - any help is appreciated. Tag: Localization Tag: 49222
  - 16
    - modify IE start page Hi, how can I modify the Internet Explorer default start page in my project in platform buuilder 4.2 ? Now I have a http://www.msn.com and I want to put my web site home page. I dont' know if I have to edit a reg file or if I need to set some variables. Thanks Carlo Tag: Localization Tag: 49217
  - 17
    - Data Abort with Chinese Build All, Built image for Chinese locale (Simplified or Traditional) on 4.1 with latest QFEs. H/W is proprietary PXA255. It works fine except "Data Abort" from applications when it is closed. It comes from explorer.exe, ceplayer.exe, CTLPNL.exe, control.exe and any applications as follows. But, it keeps working even with Data Abort. It doesn't happen with Japanes and Korean locale build. Any helps will be appreciated. Woojung Data Abort: Thread=803b85f8 Proc=801bed0c 'calibrate.exe' AKY=ffffffff PC=03f7e474 RA=03f7f2a0 BVA=0800000c FSR=00003007 TLSKERN_NOFAULT set... bypassing kernel debugger. Data Abort: Thread=822f181c Proc=801bec38 'explorer.exe' AKY=ffffffff PC=03f7e474 RA=03f7f2a0 BVA=0800000c FSR=00003007 TLSKERN_NOFAULT set... bypassing kernel debugger. Data Abort: Thread=803b85f8 Proc=801bec38 'explorer.exe' AKY=ffffffff PC=03f7e474 RA=03f7f2a0 BVA=0800000c FSR=00003007 TLSKERN_NOFAULT set... bypassing kernel debugger. Data Abort: Thread=822f181c Proc=801bed0c 'ceplayer.exe' AKY=ffffffff PC=03f7e474 RA=03f7f2a0 BVA=0800000c FSR=00003007 TLSKERN_NOFAULT set... bypassing kernel debugger. Data Abort: Thread=803b85f8 Proc=801bede0 'CTLPNL.EXE' AKY=ffffffff PC=03f7e474 RA=03f7f2a0 BVA=0800000c FSR=00003007 TLSKERN_NOFAULT set... bypassing kernel debugger. Data Abort: Thread=822c3670 Proc=801bed0c 'control.exe' AKY=ffffffff PC=03f7e474 RA=03f7f2a0 BVA=0800000c FSR=00003007 Tag: Localization Tag: 49216
  - 18
    - Get the focus on other window Hello, My system: PXA255, PB 4.2, 32 Mb Flash, 32 Mb Ram. I've programmed a driver for a 20-key matrix keyboard. Some of the keys have several characters , as mobile phones. For instance, one key has the characters "ABC2", other key "DEF3", other key "GHI4", ... The rotation that I've implemented is as following: - The user press the key. He sees the 'A' key in screen. I send a VK_LEFT key, so the caret is to the left of the 'A' key. - The user press the key. I send a VK_RIGHT key. The caret is to the right of the 'A' key. I send a VK_BACK, so I delete the 'A' key. I send a 'B' key. I send a VK_LEFT, so the caret is to the left of the 'B' key. - The user press the key. I send a VK_RIGHT key. The caret is to the right of the 'B' key. I send a VK_BACK, so I delete the 'B' key. I send a 'C' key. I send a VK_LEFT, so the caret is to the left of the 'C' key. - The user press the key. I send a VK_RIGHT key. The caret is to the right of the 'C' key. I send a VK_BACK, so I delete the 'C' key. I send a '2' key. I send a VK_LEFT, so the caret is to the left of the '2' key. When I try my driver over an alphanumeric CEdit, everything works fine, the rotation of keys is Ok. But when I try the input over a numeric CEdit, it doesn't work properly, because the driver tries to launch the alphanumeric key, but the CEdit forbiddes it. The CEdit has a strange behaviour, because the VK_BACK, VK_LEFT and VK_RIGHT keys are generated, but the alphanumeric keys are not. So, the solution is to detect if the focused CEdit has a numeric or alphanumeric input. I've tried to use GetForegroundWindow() and GetFocus (), but GetFocus() can't work across processes. I've tried to use AttachThreadInput, but this API doesn't work in Windows CE.NET. I've tried to use Subclassing, but you can not subclass a window that is in other process. So, I need your help to solve this issue. Thanks in advance. Tag: Localization Tag: 49211
  - 19
    - Source control and PB Hi I'm using clearcase as my source cotrol I having difficulties to fugure out how can i put a "command line" only project into the source control As a fact (currect me if i'm wrong) it is a must to put my driver source files under the \myplatform\drivers directory in order for it to be compiled, link, built In that case i can't even use a mapped drive to redirect the PB to I can't put all the PB in the source control I know that this is an easy issue doing using an IDE project, which i dont have Any idea Benz Tag: Localization Tag: 49206
  - 20
    - System Clock Resets We have an application that has been developed to collect data every 100ms. We are noticing the system clock is getting reset in the emulator (CE.NET 4.2). Our application never writes time; it queries it (GetSystemTime). I have disable SNTP to make sure we are not resync'ing with a time server but the problem remains. While our application is running if you launch the clock UI from the toolbar you can see when the clock reaches the end of a minute the minutes do not increase. For example say time is 12:01:59 you would expect 12:02:00 to be next, but the emulator shows 12:01:00. Plus if I examine the tick count, the tick count decreases when this occurs which makes sense based on what we are seeing. I cannot debug the emulator because the emulator crashes on OS boot up when KITL is enabled. Any ideas would be appreciated. Tag: Localization Tag: 49205
  - 21
    - USB and PXA Hi All, I would put a question on the group. Where I can found Manual o document how work the USB system driver on Windows Ce and, if possible, on the PXA255 with SA1111 companion Chip ? Thanks a lot Angelo Tag: Localization Tag: 49202
  - 22
    - Internet Explorer 5.5 vs 6.0 Hi All, I have some strange observations about IE 5.5 and 6.0: a) In IE 5.5 some fonts on webpages don't looks correctly. I installed all true type fonts in my platform on PB4.1 and PB4.2 and when i compare the appearance some webpages on IE 5.5 looks bed - some fonts are unreadable. On IE 6.0 the same pages looks ok. b) IE 6.0 in comparision with IE 5.5 is very slow on the same physical platform. When i'm scrolling some page by vertical scrollbar window refreshing is very slow. On IE 5.5 refreshing is much better. If anybody have the same observation ? Are there some solutions to solve that problems ? Cheers, Pawel Dabrowski -<*>- GPG: 0x59D98496 Tag: Localization Tag: 49198
  - 23
    - Flash for persistent storage and hive based registry Hi all, I'm a newbie in WCE.NET and Platform Builder 4.2 and i'm trying to understand how to use my on-board flash for the OS image and data/registry storaging. My platform is a pxa255 processor board with 32M strata flash (2 x 28f128j3a) and 64M sdram. My bootloader create a BINFS partition and an EXTENDED partition on the rest of the flash memory. The BINFS partition serves for the OS image (non-XIP mode). Is it possible to use the EXT partition for persistent storage and hive based registry ? Do I need for something like Intel IPSM or the NOR strata flash driver (from PB) and some registry settings (as I see in PB Help) are enough? Do I have to modify my bootloader to create a FAT partition instead of an EXTENDED? Now, when my platform boot, I can see (with stguil) only a BINFS partition. I would like to have the storage/registry partition automatically created at boot time, is it possible? Thanks in advance, best regards. Fabio Melandri ElettronicaGF Tag: Localization Tag: 49197
  - 24
    - What devices are connected Hello everyboby. My application needs to know what devices are currently connected to my WinCE machine ( for example: CF card, network adapter, USB-device, RS-232, PCMCIA-device, etc. ) How can "ask" operating system about this info. Thanks. Tag: Localization Tag: 49195
  - 25
    - Help ActiveSync Whether are necessary for start ACTIVESYNC on SMDK2410 of adjustment of the system register? Tag: Localization Tag: 49193

G'day All,

I have a question regarding localization of a WinCE 4.2 platform.

We are developing a WinCE platform where installed applications will not
be using any of the standard Windows Interfaces (eg Shell, file open
close etc), applications will manage all interfaces. The installed
application will need to support multiple lanaguages so we need to
provide full font support etc. Most likely a seperate build of the
application will be done for each target language.

My question is:

Do we need to include all the target locales in this situation?
I looks like these just provide language translation of Standard Shell
UI and System Apps etc?

Phil

Top