File System in Wince 5...

Tutorials Win: Microsoft Windows Forum

- Previous
  - 1
    - How to debug Hi Is there some good way or tool to debug Windows CE application and driver, which documents to refer ? How about Windows Mobile device , can we debug it the same as WinCE ? Thank you . Tag: File System in Wince 5... Tag: 112453
  - 2
    - nand partition i have one nand flash on my device, i want to make this nand flash as two partitions, can any body help on the registry settings required for this and what are the modifications required in the nand fmd driver and i want to expose one of the partition as a mass storage device when connected to PC. Thanks Subbarao. Tag: File System in Wince 5... Tag: 112450
  - 3
    - Delay in VoIP call for WinCE5.0 device Hi All, We are developing a MainstoneII based VoIP handheld device, on WinCE 5.0 with PXA 270 processor. On making VoIP call we are getting delay of 3 seconds. What can be possible reasons for this, whether any driver like ethernet cotroller can cause a delay. We are using SMSC 9118 ethernet controller.Plz help me in this. Thanks in advance Jipin Tag: File System in Wince 5... Tag: 112448
  - 4
    - Win CE USB Mass Storage Class Driver Hello, We are using Win CE 5.0 USB host stack for the development purpose. We found that Win CE Host stack has a very low performance. We have done few modifications in the USB Mass Storage Class driver to enhance the speed of USB transfers in Host mode. WinCE Kernel USB Class Driver fixes - 1. Changed Max Transfer size from 8KB to 32KB. Result - Number of SCSI commands was reduced. 2. Removal of SCSI Test Unit Ready(TUR) Command during Read/Write operation. Result - Time taken by TUR Command is reduced during Read/Write operation. 3. WinCE Scatter-Gather Buffer changed from 8 to 128 (SG_MAX_BUF) Result - Disk I/O Delay is reduced by increasing the number of buffers Changes in MS WinCE Kernel system Memory 1. Memory Type changed to RAMdisk Result - RAMdisk access times are faster than WinCE system memory We need know, 1. Whether the above modifications will affect the stability of the Win CE kernel and system. 2. Will they have any detrimental affect on their internal kernel modules. Thanks in Advance, Sheeja Tag: File System in Wince 5... Tag: 112435
  - 5
    - Audio channels volume is inverted...? Recently we faced this problem: 1)the 'waveOutSetVolume' documentation states that 'The low-order word [of 'DWORD dwVolume' parameter] contains the left-channel volume setting, and the high-order word contains the right-channel setting'. 2)AC97 codec registers for volume(s) are 16 bit: the LSB is the attenuation for the right channel, while the MSB is the attenuation for the left channel (actually only 5 bits out of 8 are used). Let's take a look to the low-level function which sets the volume in %_WINCEROOT%\..\DRIVERS\WAVEDEV\UNIFIED\ENSONIQ (comments are mine): **************************************************** CDriverContext::SetVolume (ULONG ulVolume) m_ulVolume = ulVolume; /* The '&' keeps only the higher 5 bits due to the AC97 register format. Then we 'justify' the data to the right */ USHORT usLeft = (USHORT) ((m_ulVolume & 0x0000F800) >> 11); USHORT usRight = (USHORT) ((m_ulVolume & 0xF8000000) >> 27); /* Since AC97 volume register represents the attenuation (i.e. 0 dB == MAX_VOLUME), we subtract the volume from 0x1F */ usLeft = 31 - usLeft; usRight = 31 - usRight; /* Here we build up the value to write in the AC97 register: NOTE that we are putting the RIGHT volume in the higher part of the word when we should put the LEFT volume, and viceversa */ USHORT usRegVal = (usRight << 8) | usLeft; /* Write data to the codec */ m_pDevice->WriteCodecRegister(AC97_PCMOUT_VOL, usRegVal); **************************************************** All the other audio drivers I've seen in WINCE600 (and previous version of the OS), although with slightly different semantics, seem to make the same mistake... Am I wrong or missing something...? -- Luca Calligaris www.eurotech.it Tag: File System in Wince 5... Tag: 112432
  - 6
    - Serial Problem with USB I have the following problem with serial devices connected through USB. Situation: Windows CE 5.0 running on a PXA270. NET CF 2.0 (No SP) USB Devices connected through a USB HUB. 1 FTDI USB To Serial device. Other USB devices (Including serial devices, and Mass storage devices) Recognition of all the USB Devices work without problems. When i boot up with my FTDI Device attached, all works and i can open the serial port and communicate, But as soon as i attach an other Serial USB device the FTDI Serialport gives an error (I suspect the port gets closed). This only happens if i attach a Serial based device (A GPS Mouse, and Microsoft Wireless keyboard,mouse for example) the problem does not occur if i attach a Non Serial device like a Storage device. The problem also doesn't occur if i attach another FTDI Serial device. When i attach the Serial device and then bootup the device no problems occur aswell so the devices are all recognised, it's only the fact that if you attach the device after bootup, and when the other serialport has already been opened my problem occurs. For test purposes i removed all the drivers for the GPS Mouse in the registry, so whenever i attach the GPS Mouse it's not recognised as a valid device and displays the famous add driver dialog, but even then my serialport gives me an error although in theory i would think that nothing would happen. Could anyone shed some light on this issue. If you need more info about the settings in the registry i can post them, only didn't want to make this post to long Best Regards, mario Tag: File System in Wince 5... Tag: 112429
  - 7
    - (Parallel Port) Why cannot output data to LPT port ? Dear Sir, I use WINCE 5.0/6.0 ro develop my project which have a parallel port. I reference http://support.microsoft.com/default.aspx?scid=kb;EN-US;823179 to develop a program to output data to LPT port. But system always cannot output data. Error Message : ========================== Open LPT port OK GetCommState OK SetCommState OK GetCommTimeouts OK SetCommState OK WriteFile OK WriteFile --> 0 Byte Do anyone have idea about this issue ? BR, Wiles The following is my source code. //---------------------------------------------------------- #include "stdafx.h" #include "resource.h" #include <windows.h> #include <stdio.h> #include <string.h> int WINAPI WinMain(HINSTANCE hInstance, HINSTANCE hPrevInstance, LPTSTR lpCmdLine, int nCmdShow) { HANDLE hParallelPort = NULL;; DCB MyDCB; COMMTIMEOUTS MyCommTimeouts; char String_data = 'A'; DWORD BytesWritten = 0; DWORD dwRead = 0; char buf[] = "Test"; char new_buf[] = ""; RETAILMSG(1, (_T("==========================\r\n"))); // hParallelPort = CreateFile(TEXT("LPT1:"), GENERIC_READ Or GENERIC_WRITE, 0, 0, OPEN_EXISTING, FILE_ATTRIBUTE_NORMAL, 0); hParallelPort = CreateFile(TEXT("LPT1:"),GENERIC_READ | GENERIC_WRITE, 0,NULL,OPEN_EXISTING,FILE_ATTRIBUTE_NORMAL,NULL); if(hParallelPort == NULL) { RETAILMSG(1, (_T("Open LPT port Fail\r\n"))); } else { RETAILMSG(1, (_T("Open LPT port OK\r\n"))); } if(!GetCommState(hParallelPort, &MyDCB)) { RETAILMSG(1, (_T("GetCommState Fail\r\n"))); } else { RETAILMSG(1, (_T("GetCommState OK\r\n"))); } MyDCB.BaudRate = 9600; MyDCB.ByteSize = 8; MyDCB.Parity = NOPARITY; MyDCB.StopBits = ONESTOPBIT ; if(!SetCommState(hParallelPort, &MyDCB)) { RETAILMSG(1, (_T("SetCommState Fail\r\n"))); } else { RETAILMSG(1, (_T("SetCommState OK\r\n"))); } if(!GetCommTimeouts(hParallelPort, &MyCommTimeouts)) { RETAILMSG(1, (_T("GetCommTimeouts Fail\r\n"))); } else { RETAILMSG(1, (_T("GetCommTimeouts OK\r\n"))); } MyCommTimeouts.ReadIntervalTimeout = 0; MyCommTimeouts.ReadTotalTimeoutConstant = 0; MyCommTimeouts.ReadTotalTimeoutMultiplier = 0; MyCommTimeouts.WriteTotalTimeoutConstant = 0; MyCommTimeouts.WriteTotalTimeoutMultiplier = 0; if(!SetCommTimeouts(hParallelPort, &MyCommTimeouts)) { RETAILMSG(1, (_T("SetCommState Fail\r\n"))); } else { RETAILMSG(1, (_T("SetCommState OK\r\n"))); } if(!WriteFile(hParallelPort, buf, strlen(buf), &BytesWritten, 0)) { RETAILMSG(1, (_T("WriteFile Fail\r\n"))); } else { RETAILMSG(1, (_T("WriteFile OK\r\n"))); } RETAILMSG(1, (_T("WriteFile --> %dByte\r\n"),BytesWritten)); CloseHandle(hParallelPort); return 0; } Tag: File System in Wince 5... Tag: 112428
  - 8
    - Does CE 6.0 R2 new nandflash driver model support IOCTL_DISK_READ ?? hi,all, Firstly, my new nandflash driver seems working well, and I could access nand in device explorer by common file operation method. In one of my app,I need access nandflash by DeviceIoControl. But when I sent IOCTL_DISK_READ to nand store handle,it always complained invalid parameter. While i sent the same parameters to SD or my old flash driver, it could work correctly. MS said they provided flashmdd.dll, flashpart.dll to manage flash device, and there is no source code for traceing. I am confused deeply. #define USESTORE 1 int _tmain(int argc, TCHAR *argv[], TCHAR *envp[]) { DWORD dwError; BOOL fResult; DWORD dwBytesReturned; //open store of nandflash _tcscpy(g_szDeviceName,_T("DSK1:")); //-->DSK1: for nand, DSK2 for SD #if USESTORE g_hStore = OpenStore(g_szDeviceName); #else g_hStore = CreateFile(g_szDeviceName, GENERIC_READ | GENERIC_WRITE, FILE_SHARE_READ | FILE_SHARE_WRITE, NULL,OPEN_EXISTING, 0,NULL); #endif if ((g_hStore == NULL) || (g_hStore == INVALID_HANDLE_VALUE)) { dwError = GetLastError(); RETAILMSG(1, (_T( "Failed to open store %s; error = %u\r\n" ), g_szDeviceName, dwError)); goto EXIT; } RETAILMSG(1, (_T("Opened store %s\r\n"), g_szDeviceName)); //read disk info RETAILMSG(1,(_T("IOCTL_DISK_GETINFO =0x%X\r\n"),IOCTL_DISK_GETINFO)); // read disk information fResult = DeviceIoControl( g_hStore, IOCTL_DISK_GETINFO, NULL, 0, &g_diDiskInfo, sizeof(g_diDiskInfo), &dwBytesReturned, NULL); if (!fResult) { RETAILMSG(1,(_T("IOCTL_DISK_GETINFO Failed,GetLastError:0x%X\r\n"), GetLastError())); goto EXIT; } RETAILMSG(1, (_T("Get disk Info success %s\r\n"), g_szDeviceName)); DUMP_DISKINFO(g_diDiskInfo); //read sector PBYTE pBuffer = (PBYTE)LocalAlloc(LPTR, g_diDiskInfo.di_bytes_per_sect); if (pBuffer != NULL) { DWORD adwPFNs[512]; memset(adwPFNs, 0, sizeof(adwPFNs)); BOOL bLockRes = LockPages(pBuffer, g_diDiskInfo.di_bytes_per_sect, adwPFNs, LOCKFLAG_WRITE); if (bLockRes) { bLockRes = UnlockPages(pBuffer, g_diDiskInfo.di_bytes_per_sect); } SG_REQ sgReq; DWORD dwBytesReturned; sgReq.sr_start = 1; sgReq.sr_num_sec = 1; sgReq.sr_num_sg = 1; sgReq.sr_status = 0; sgReq.sr_callback = NULL; sgReq.sr_sglist[0].sb_buf = pBuffer; sgReq.sr_sglist[0].sb_len = g_diDiskInfo.di_bytes_per_sect; BOOL bResult = DeviceIoControl(g_hStore, IOCTL_DISK_READ, &sgReq, sizeof(SG_REQ), NULL, 0, &dwBytesReturned, NULL); if (!bResult) { RETAILMSG(1,(_T("IOCTL_DISK_READ Failed:0x%X\r\n"),GetLastError())); goto EXIT; } RETAILMSG(1,(_T("IOCTL_DISK_READ success...\r\n"))); } EXIT: if (pBuffer!=NULL) { LocalFree(pBuffer); } #if USESTORE #else CloseHandle(g_hStore); #endif return 0; } **************************** Debug info: Opened store DSK1: IOCTL_DISK_GETINFO =0x71C00 Get disk Info success DSK1: DSK1: bytes per sector = 2048 DSK1: cylinders = 884 DSK1: flags = 0x8 DSK1: heads = 1 DSK1: sectors = 128 DSK1: total sectors = 113152 !!DecodeAPI: invalid handle! (h = 0297000a, iApiSet = 00000002 'NONE', pActvProc ->dwId = 0297000a) ObjectCall: returning 8037cce4 IOCTL_DISK_READ Failed:0x57 ************************************ The IOCTL_DISK_GETINFO operation had passed correctly. Is there any hint? any help will be appreciated! Tag: File System in Wince 5... Tag: 112425
  - 9
    - WinCE driver question .. Hi Are all Windows CE drivers user mode drivers, unlike PC Windows kernel mode drivers ? Do Windows CE drivers have IRQ level like PC Windows drivers ( hardware IRQ > Software IRQ ) ? Thank you . Tag: File System in Wince 5... Tag: 112423
  - 10
    - USB Mass Storage-Usbmsfn.dll problem. Hi All, Right now my CE device is getting detected as a Mass Storage Device. I could see the drive as "USB Mass Storage Device D:" . But if i try to access, i could see only empty folder and when i view the properties, "Used Space" and "Free Space" are shown as 0 bytes. My platform USBFn driver is derived from pxa27x which is available in public folder. From my BSP platfrom i could get retail messages from pxa27x usbfn driver. But not from usbmsfn.dll which tells me that usbmsfn.dll is not at all getting loaded. I am not sure, what is causing usbmsfn.dll driver not to load? Please give me your inputs. Thanks Saravana Tag: File System in Wince 5... Tag: 112409
  - 11
    - nand fmd driver, long boot time hello, I see my device read every single sector during boot, is it normal? does TFAT/FAT type, and the exist of a BINFS partition affect boot time? this is my reg setting [HKEY_LOCAL_MACHINE\Drivers\BuiltIn\xs27xNand] "Profile"="FlashDisk" "Dll"="xs27xNand.dll" "Prefix"="DSK" "IClass"="{A4E7EDDA-E575-4252-9D6B-4195D48BB865}" "FriendlyName"="XScale 27x Nand flash Driver" "Order"=dword:0 "Index"=dword:1 [HKEY_LOCAL_MACHINE\System\StorageManager\Profiles\FlashDisk] "DefaultFileSystem"="FATFS" "Name"="FlashDisk" "Folder"="FlashDisk" "MountHidden"=dword:0 "AutoMount"=dword:1 "AutoPart"=dword:1 "AutoFormat"=dword:1 [HKEY_LOCAL_MACHINE\System\StorageManager\Profiles\FlashDisk\FATFS] ; "FormatTfat"=dword:1 "EnableCache"=dword:1 Tag: File System in Wince 5... Tag: 112407
  - 12
    - Windows CE 6.0 AlphaT9 Input Method Hi Since some features like the cellcore module moved from the Windows Mobile to the Windows Embedded CE 6.0 (R2), I wondered if there is also support for the AlphaT9 Input Method. I couldn't find any information about this. Thanks J. Tag: File System in Wince 5... Tag: 112406
  - 13
    - PCI Express Support? In the CE 6.0 docs I am not seeing explicit support for PCI Express, is this correct? Will there be support for it in the future, and if so, when? Thanks. Tag: File System in Wince 5... Tag: 112400
  - 14
    - WindowsCE 5.0 usb printing Hi, I'm trying to enable usb printing from Windows CE 5.0. I have managed to load the default usb printer class driver (usbprn.dll) and when printing from WordPad I can see my printer name "Deskjet 460" and port "LPT1:". But when i proceed to printing, I got this error: LPT_IOControl(0x160014, 0xe03eef4, 4, 0xe03eef8) LPT_IOControl(0x160014) : ERROR_NOT_SUPPORTED <LPT_IOControl:0 LPT_Close(0x50b50) The Io control code 0x160014 refers to IOCTL_PARALLEL_GET_ECP_REV_TRANS which is not supported by usbprn.dll. Is there anything that I missed here? Regards, Doan Tag: File System in Wince 5... Tag: 112398
  - 15
    - NdisMInitializeWrapper Problem? Hi all, I am working on PXA270 processor I have taken Sample code of WLAN from \WINCE500\PRIVATE\WINCEOS\COMM\NDISMODS\LAN\PCX500 location. I have used it in my platform driver folder. I got one error when i downloaded image CODE==> DriverEntry( IN PDRIVER_OBJECT DriverObject, IN PUNICODE_STRING RegistryPath ) { NDIS_HANDLE NdisWrapperHandle=NULL; RETAILMSG (1, (TEXT("DriverEntry Initializing..\r\n"))); RETAILMSG (1, (TEXT("In NdisMInitializeWrapper\r\n"))); // Initialize the wrapper. NdisMInitializeWrapper( &NdisWrapperHandle, DriverObject, RegistryPath, NULL ); RETAILMSG (1, (TEXT("Out NdisMInitializeWrapper\r\n"))); } OUTPUT==> DriverEntry Initializing.. In NdisMInitializeWrapper Data Abort: Thread=87d33784 Proc=81906000 'device.exe' AKY=00000005 PC=03c314cc(ndis.dll+0x000114cc) RA=01e21224(pcx500.dll+0x00001224) BVA=06000000 FSR=00000007 I got first massage only "In NdisMInitializeWrapper" but not get secound one "Out NdisMInitializeWrapper". Is any body know whats the problem in 'NdisMInitializeWrapper' ? Thanks in advance Swapnil Tag: File System in Wince 5... Tag: 112397
  - 16
    - when will ms release sdk for ce6? or there already is ? 3x Tag: File System in Wince 5... Tag: 112391
  - 17
    - Storage Manager : Create 2 partitions Dear Professional Buddies, From the title shows us, We can create 2 partitions in 1 storage media deive, and we can see "HardDisk", "HardDisk2" directories under the Root directory. ( If we configured Flash driver registry with "Folder"="HardDisk" ). But I have a question, I searched all of the registry and I did not see where the "HardDisk" and "HardDisk2" configuration are. Because I want to create 2 partitions from registry setting, and so on, we will not need to do it from storage manager. Thanks for your HELP!! Tag: File System in Wince 5... Tag: 112384
  - 18
    - The Turn-by-Turn map SDK Hi: I hope someone had some experience about the Turn-by-Turn map device, for example, Tom-Tom device. And please give me some advise. I need to find a vendor (software or hardware) to sell a Turn-by-Turn Mapping solution. The hardware platform is a X86 Windows CE platform. This platform is based on a CEPC, x86 platform. The volume of platform is about several hundreds device. So I hope, there is a vendor could sell a SDK, like map engine, GUI SDK implemented by C++ or .NET Compact Framework and run on the x86 Windows CE platform. So I could implement Turn-by-Turn mapping into or intergate the propritary product. Thanks Lu Tag: File System in Wince 5... Tag: 112376
  - 19
    - Flash demo on EZPAD with CE 4.10? I wanted to run a flash demo (SWF file) on an EZPAD EP8402 running CE 4.10. I can't find a version of flash that I can install. Unsuccessfully tried fpc_ppc_en.cab. Is this going to be possible or should I give it up? Thanks ** Posted from http://www.teranews.com ** Tag: File System in Wince 5... Tag: 112372
  - 20
    - How to write File system filter driver on Windows CE 5.0 Hi there, I am having USB Mass storage feature working on my target (Windows CE 5.0). Also I have boot partition and support for Hive based registry working. I have totally 3 partitions on my internal flash card. ( BINFS partition where in I have stored NK.bin and 1st DOS32 partition has been mounted as root and 2nd DOS32 partition is used for user data storage. I want to expose 2nd DOS32 parition as mass storage. (i.e. Selective partition exposure). Following post says there are couple of ways of doing it. One of them is writing file system filter. http://groups.google.co.in/group/microsoft.public.windowsce.platbuilder/browse_thread/thread/18759b99fcc05bf2/de2258cfaacf12c4?hl=en&lnk=st&q=Selective+partition+exposure#de2258cfaacf12c4 Is there any reference file system filter available in Windows CE 5.0? Any inputs will be helpful! Thanks in advance! Tag: File System in Wince 5... Tag: 112371
  - 21
    - Error 4309 returned when writing files Hello, We have a WinCE 5.0 Core system running on a 1 Ghz x86 platform. The hard disk drive is set up as a CF card. Our program previously ran on WinCE 4.x with no problems, but now we repeatedly get errors when writing to the disk drive. GetLastError() returns 4309 (resource required). I suspect there is some security issue. We have the NoDefaultUser registry setting set to 0 by default. The platform was started from an internet appliance base and we have omitted all items we dont use in order to adhere to the core licensing agreement. We have no use for any "user" security. We need to be certain it is defeated, yet I haven't yet determine a successful solution. Any suggestions would be appreciated. Thanks, Ken Tag: File System in Wince 5... Tag: 112361
  - 22
    - IRQ_BULVERDE_MAX CE 6.0 Question Hey all, I am porting a 270 based platform from CE 5.0 to CE 6.0 and have found a discrepancy with the defined value of IRQ_BULVERDE_MAX between the two versions. In CE 5.0 it is defined as follows... #define IRQ_BULVERDE_MAX IRQ_RTCALARM ...where IRQ_RTCALARM = 31. In CE 6.0 it is defined as follows... #define IRQ_BULVERDE_MAX 63 //icmr (32) + icmr2 (32) Is there a reason this was changed? I am defining additional platform specific IRQ values based off of the IRQ_BULVERDE_MAX value, but this paradigm is broken in CE 6.0 because the OALIntrStaticTranslate() routine (common lib, map.c) is comparing against the OAL_INTR_IRQ_MAXIMUM value which is defined as 64 for both versions. What this causes is the IRQ translation in CE 6.0 to be skipped because the compare fails, which in turn causes the SYSINTR to be mapped to the IRQ init value of -1 and then breaks IRQ dependent drivers. Obviously, I can manage to work around the issue, but I just wanted to get the reasoning behind the change to IRQ_BULVERDE_MAX. Tag: File System in Wince 5... Tag: 112350
  - 23
    - how could i save files in windows folder? can i do it on ce5? or ce6? what's the solution? I know windows mobile can do it,3x Tag: File System in Wince 5... Tag: 112347
  - 24
    - Compact Framework 3.5 CEC file for Windows CE 5.0 wanted Hello there, I would like to update my platform (Windows CE 5.0), but I'm missing the CEC file for Windows CE 5.0 platform builder. The only thing I found was: http://support.microsoft.com/kb/947560/ I've got a licensed Windows CE Platform Builder, a valid product key for "Windows CE 5.0 Pro" & we are producing Windows CE devices. How do I get hands on QFE updates like the Wincepb50-080115-kb947560-armv4i.msi? Thanks, Armin Sczuka Tag: File System in Wince 5... Tag: 112344
  - 25
    - How to change the screen color? My platform is Windows CE 6.0. I want to change the screen color during Windows CE boot, the default color is black. Is it possible to do that? -- Regards, Goldbach Tag: File System in Wince 5... Tag: 112334
- Next
  - 1
    - How to change the -- Regards, Goldbach Tag: File System in Wince 5... Tag: 112333
  - 2
    - WinCE Graphics Hi, Can anyone explain me the basic display operations in Wince like BitBlt etc. Also can anyone tell me the benchmark values for time taken by a particular display driver operation like BitBlt, DrawText etc. I mean what should be the ideal time taken by Display Driver for a particular display operation eg. BitBlt. 1) Are these values documented some where? 2) Are these values platform dependent? Thanks in advance. Regards, Ram P Tag: File System in Wince 5... Tag: 112332
  - 3
    - explorer ? How kill explorer or no loaded explorer (still keep Standard Shell) Tag: File System in Wince 5... Tag: 112328
  - 4
    - Problem cloning calibrui CE 5.0: I followed the instructions to clone the touch screen calibration CalibrUi, but my changes in the resources and changes to the code are not making it into the build. I don't understand how the clone gets the resources and the compiled code into the build instead of the original copies, so I'm having trouble tracking down why it doesn't work. Can anyone suggest where to look? Tag: File System in Wince 5... Tag: 112321
  - 5
    - SMDK2440 USBD suspend/resume problem Hi all I am working with smdk2440 bsp. The Activesync works good through usb_serial function driver. The usb don't connect after resuming from suspend state, it seems that the USB device controller does'nt re-initialize after resume. Any hint will be welcome Thanks -- Message posted via PocketPCJunkies.com http://www.pocketpcjunkies.com/Uwe/Forums.aspx/wince-pb/200805/1 Tag: File System in Wince 5... Tag: 112319
  - 6
    - FAT partition Backup/Restore Hi, I need to create a procedure that will allow the user to backup and restore data from the FAT partition available on our CE 5.0 device's internal NAND flash storage. I basically need to create a mechanism that will create a bin file containing all the data- much like the one Norton Ghost creates on a PC. The entire procedure needs to be implemented in the bootloader. Does anyone have any suggestion on what would be the best approach to do the above? Tag: File System in Wince 5... Tag: 112315
  - 7
    - Block device auto format prompt I have a problem which seems like it should be simple to solve but I can't work it out. I have developed a block device which is designed to store a file system on a file. This file can then be mounted and unmounted programatically to allow the user access to the filesystem. I've used the technique of using a dummy block device which bootstraps the normal FAT FSD, then the block device can be activated and deactived to bring the file system up and down. However the problem I has is that if the file has just been created it isn't formatted, so I need the option of being able to format it. I want a prompt to ask if the device should be formatted, then the user can decided to format or not to format. My registry keys are: [HKEY_LOCAL_MACHINE\System\StorageManager\Profiles\MyDisk] "Name"="MyDisk" "Folder"="MountedStorage" "AutoMount"=1 "AutoFormat"=1 "AutoPart"=0 "PartitionDriver"="" "DefaultFileSystem"="FATFS" [HKEY_LOCAL_MACHINE\System\StorageManager\Profiles\MyDisk\FATFS] "Flags"=4 Strangly it use to prompt me before formatting, but after I added the PartitionDriver entry to the registry the original auto format prompt stopped appearing. But without this key the disk was not being formatted correctly and the MBR/Sector 0 didn't appear to be correct. Previously I could set AutoFormat to 1 and the format was silent, or AutoFormat to 0 and the prompt appeared before mounting and formatting. Now all I get is a silent auto format, or nothing at all. This silent autoformat will cause a problem because the software on the PDA is designed to operate with an existing 2K/XP driver. If this file was created on the desktop and formatted as NTFS rather than FAT then clearly I don't just want the PDA to silently reformat the device and lose all the data. Another possibilty might be if I can programatically format the device. But I don't own the fsd driver so I don't know how to ask it to format the file system (e.g. using FSDMGR_FormatVolume), and I can't open the volume and use IOCTL_DISK_FORMAT_VOLUME or IOCTL_DISK_FORMAT_MEDIA because until it is formatted it won't mount so \MountedStorage\Vol: doesn't exist. Can anyone point of a solution to the auto format prompt, or tell me what I am missing with regard to a programatic format? Jamie Tag: File System in Wince 5... Tag: 112306
  - 8
    - FREEZE/PXA255/WindowsCE 5.0 Hi, I have a COMPULab CM-X255 board with a PXA255 with WindowsCE 5.0. I encounter a FREEZE after several hours/days for abot 19 minutes. afterwards it is running normally. Has anyone experienced the same problem ? Has anyone a solution ? regards, Martin Tag: File System in Wince 5... Tag: 112305
  - 9
    - IRQ_DMAC and auido Hi, i have an audio and wlan driver using dma. audio is mainstoneii wavedev driver but using i2s port to transfer instead of ac97. using dma channels 1,4 and 2,3 (i2s). wlan is using dma channels 13,14. platform is Ce 5, pxa270 i made a modification in OEMInterruptHandler to seperate them. else if(irq == IRQ_DMAC) { volatile BULVERDE_DMA_REG *g_pDMAReg= NULL; g_pDMAReg = (volatile BULVERDE_DMA_REG *) OALPAtoVA(BULVERDE_BASE_REG_PA_DMAC, FALSE); CLRREG32(&g_pICReg->icmr, (1 << irq)); if (g_pDMAReg->dint & DMA_AUDIO_INTR) { sysIntr = SYSINTR_AUDIO; } else if (g_pDMAReg->dint & DMA_WLAN_INTR) { sysIntr = SYSINTR_SSPC_DMA; } } they both work alone. but together when i play an audio it stucks or logs a crash in device.exe OEMInterruptHandler 0x2002 & DMA_AUDIO_INTR) Data Abort: Thread=83f2e240 Proc=81c26300 'device.exe' AKY=ffffffff PC=03fc3994(coredll.dll+0x00053994) RA=033c32a4(wavedev.dll+0x000032a4) BVA=0650fe68 FSR=000004f6 . do you have any suggestion to fix this. Thanks Alli Tag: File System in Wince 5... Tag: 112303
  - 10
    - How does code in PRIVATE folder get reflected in the final NK.bin Hi, I recently installed the Dec07 cumulative update. In this update there are changes to source code in the PRVATE folder. Also I had a look in the PUBLIC\COMMON\OAK\LIB\ARMV4I folder and found that there are libs present correspondign to some components that have changed in the PRIVATE folder. I could not find all the libs corresponding to all the changed components. So, my question is, will it be fine if I do not install the PRIVATE source code? Is it OK if I get the updated libs in PUBLIC folder only and then build an image? What is the general procedure for including the PRIVATE folder source code into the NK.bin? I dont think the PRIVATE folder would be built ever, instead the corresponding libs from PUBLIC folder woulc be used. Right? - Varun Tag: File System in Wince 5... Tag: 112299
  - 11
    - pxa270 mainstone 2, ce5.0 usb host hello, I want to turn off the over current protection support in the usb host. I looks like even if I turn it off in PDD, it's somehow turned back on again in MDD. how can I tell the MDD that I am not supporting over current protection? Tag: File System in Wince 5... Tag: 112295
  - 12
    - What is the reason that trigger the "Network and Dial Up Connections UI"? My WINCE5 device always popped up a dialing dialog just a while after startup. The dialog is the "Network and Dial Up Connections UI". If I set following item in register: [HKEY_CURRENT_USER\ControlPanel\Comm] "AutoCnct"=dword:0 then the dialing dialog will not be showed, but another dialog popped up. The tilte is "communication error" ,and the dialog said that it can not start the communication with PC, and the error number is 608 ... The device did not show the dialog before, and I have not changed the components of OS for a long time. Yes ,there is IE component in the OS which is the dependency of .NET2 , but there is no network service should be started at startup, and I have installed all QFE . Any advice? Thanks. Tag: File System in Wince 5... Tag: 112294
  - 13
    - pxa255 and the sdram problem dear all, since I posted several days ago about 128 sdram configuration, I did not work it out anymore,there must be some mistakes i have not found yet,so i need u help guys.. okay,the platform is following: CPU : Xscale pxa255 OS : Windows CE .Net 4.2 Flash : 32MB SDRAM : 128MB (32MBX4) well,to configure my 128M sdram,I modified some files below: F:\WINCE420\PLATFORM\XSBase255\INC memmap.inc F:\WINCE420\PLATFORM\XSBase255\INC memdefs.h F:\WINCE420\PLATFORM\XSBase255\FILES config.bib F:\WINCE420\PLATFORM\XSBase255\INC xsc1.inc xsc1.h xsc1bd.inc xsc1bd.h F:\WINCE420\PLATFORM\XSBase255\KERNEL\HAL\ARM fwxsc1.s when all of modifies had done,I download the NK.bin, and the debug information shows: rom_offset=0x0. Found pTOC signature. ROMHDR at Address 800B8044h RomHdr.ulRAMStart=81C50000h RomHdr.physfirst=800B8000h. Done. Writing 0x80076BD8 to flash address 0xB8340000 (length=0xA40). Sector=0x200 (Length=0x6) Block=0x1 (Length=0x1). Handling non-block aligned data... FlashErase: Unlocking flash block(s) [0x1, 0x1] (please wait): Done. Erasing flash block(s) [0x1, 0x1] (please wait): .Done. Writing to flash (please wait): Done. Got EDBG_CMD_JUMPIMG Got EDBG_CMD_CONFIG, flags:0x00000000 Download successful! Jumping to image at physical 0xA00B9000... Begin ****************************************************** ****************************************************** ****************************************************** ****************************************************** ****************************************************** OEMInitDebugSerial using UART2 Windows CE Kernel for ARM Built on Mar 13 2003 at 22:54:19 ProcessorType=02d0 Revision=6 sp_abt=ffff5000 sp_irq=ffff2800 sp_undef=ffffc800 OEMAddressTable = 800b9ef4 as u see,my system hung at last, if in normal,sp=ffffc7cc should be printed behind OEMAddressTable = 800b9ef4 but now,system hung there.... could u give me some suggestions? thank u in advance. Tag: File System in Wince 5... Tag: 112292
  - 14
    - Help with PartitionTable Hello, I have an x86 WinCE50 system that uses the ATAPI IDE driver for a system CF card. Currently, I have the CF card partitioned into 2 parts: *Partition1 = Fat16 bootable partition with CEPC Nk.bin *Partition2 = TFAT formatted partition for WinCE use. I am currently trying to mount the partition 2 as root, but having no luck at all. I have tried the following approaches. 1) Use MountAsRoot and AutoMount keys for partitions to set which should mount as root, making sure to set Part1 MountAsBootable=0 so it does not think system/hive files are on the drive. Result: Partition 1 still mounts to root. This seemed to have no effect. Maybe I am messing up the way I use the Profile? (HDProfile \Part00\ see my reg below)? 2) Use the 'cheating' method to set the PartitionTable key 0x04 to invalid FS. (suggested here: http://groups.google.com/group/microsoft.public.windowsce.platbuilder/browse_thread/thread/e122bf548aab3c7c/c61f11d3a810184f) [HKLM\System\StorageManager\PartitionTable] "04"="SYSBOOT" Result: Both partition 1 and 2 do not mount and the system halts after storage manager. To my understanding, the first partition formatted in FAT16 is 0x04. However, shouldn't my TFAT partition be type x0B (MS-DOS 32 bit FAT)? Perhaps I am wrong in my assumptions of how the PartitionTable works. 3) Setting the "PartitionDriverName" to blank in an attempt to load null partition driver [HKLM\System\StorageManager\Profiles\HDProfile\Part00] "PartitionDriverName"="" [HKLM\System\StorageManager\Profiles\HDProfile\Part01] "PartitionDriverName"="MSPART" Result: Both partitions still loaded. Here is where I am at stuck. Can anyone offer advice or help? Thanks in advance -t Below are my current registry settings - some may have been enabled/ disabled per the 3 steps above (which I tried one at a time). [HKLM\System\StorageManager\Profiles\HDProfile] "MountAsRom"=dword:0 "MountAsRoot"=dword:0 "MountAsBootable"=dword:0 "MountPermanent"=dword:0 "Flags"=dword:00080064 [HKLM\System\StorageManager\Profiles\HDProfile\FATFS] "MountAsRom"=dword:0 "MountAsRoot"=dword:0 "MountAsBootable"=dword:0 "MountPermanent"=dword:0 "Flags"=dword:00080064 [HKLM\System\StorageManager\Profiles\HDProfile\Part00] "AutoMount"=dword:0 "AutoFormat"=dword:0 "AutoPart"=dword:0 "DefaultFileSystem"="FATFS" ; "PartitionDriver"="mspart.dll" "PartitionDriver"="" "MountAsRom"=dword:0 "MountAsRoot"=dword:0 "MountAsBootable"=dword:0 "MountPermanent"=dword:0 "Flags"=dword:00080064 [HKLM\System\StorageManager\Profiles\HDProfile\Part01] "AutoMount"=dword:1 "AutoFormat"=dword:0 "AutoPart"=dword:0 "DefaultFileSystem"="FATFS" "PartitionDriver"="mspart.dll" "MountAsRom"=dword:1 "MountAsRoot"=dword:1 "MountAsBootable"=dword:1 "MountPermanent"=dword:0 "Flags"=dword:00080064 Tag: File System in Wince 5... Tag: 112290
  - 15
    - Help with PartitionTable Hello, I have an x86 WinCE50 system that uses the ATAPI IDE driver for a system CF card. Currently, I have the CF card partitioned into 2 parts: *Partition1 = Fat16 bootable partition with CEPC Nk.bin *Partition2 = TFAT formatted partition for WinCE use. I am currently trying to mount the partition 2 as root, but having no luck at all. I have tried the following approaches. 1) Use MountAsRoot and AutoMount keys for partitions to set which should mount as root, making sure to set part1 MountAsBootable=0. [HKEY_LOCAL_MACHINE\System\StorageManager\Profiles\HDProfile \Part00\FATFS] "AutoMount"=dword:0 "MountAsRoot"=dword:0 "MountAsBootable"=dword:0 [HKEY_LOCAL_MACHINE\System\StorageManager\Profiles\HDProfile \Part01\FATFS] "AutoMount"=dword:1 "MountAsRoot"=dword:1 "MountAsBootable"=dword:1 Result: Partition 1 still mounts to root. This seemed to have no effect. Am I messing up the way I use the Profile? (HDProfile \Part00\FATFS)? 2) Use the 'cheating' method to set the PartitionTable key 0x04 to invalid FS. (suggested here: http://groups.google.com/group/microsoft.public.windowsce.platbuilder/browse_thread/thread/e122bf548aab3c7c/c61f11d3a810184f and by others as well): [HKEY_LOCAL_MACHINE\System\StorageManager\PartitionTable] "04"="SYSBOOT" Result: Both partition 1 and 2 do not mount and the system halts after storage manager. To my understanding the first partition formatted in FAT16 is 0x04. However, shouldn't my TFAT partition be type x0B (MS-DOS 32 bit FAT)? Perhaps I am wrong in my assumptions of how the PartitionTable works. 3) Setting the "PartitionDriverName" to blank in an attempt to load null partition driver [HKEY_LOCAL_MACHINE\System\StorageManager\Profiles\HDProfile\Part00] "PartitionDriverName"="" [HKEY_LOCAL_MACHINE\System\StorageManager\Profiles\HDProfile\Part01] "PartitionDriverName"="MSPART" Result: Both partitions still loaded. Here is where I am at stuck. Can anyone offer advice or help? Thanks in advance -t Below are my current registry settings: [HKEY_LOCAL_MACHINE\System\StorageManager\Profiles\HDProfile] "MountAsRom"=dword:0 "MountAsRoot"=dword:0 "MountAsBootable"=dword:0 "MountPermanent"=dword:0 "Flags"=dword:00080064 [HKEY_LOCAL_MACHINE\System\StorageManager\Profiles\HDProfile\FATFS] "MountAsRom"=dword:0 "MountAsRoot"=dword:0 "MountAsBootable"=dword:0 "MountPermanent"=dword:0 "Flags"=dword:00080064 [HKEY_LOCAL_MACHINE\System\StorageManager\Profiles\HDProfile\Part00] "AutoMount"=dword:0 "AutoFormat"=dword:0 "AutoPart"=dword:0 "DefaultFileSystem"="FATFS" ; "PartitionDriver"="mspart.dll" "PartitionDriver"="" "MountAsRom"=dword:0 "MountAsRoot"=dword:0 "MountAsBootable"=dword:0 "MountPermanent"=dword:0 "Flags"=dword:00080064 [HKEY_LOCAL_MACHINE\System\StorageManager\Profiles\HDProfile\Part01] "AutoMount"=dword:1 "AutoFormat"=dword:0 "AutoPart"=dword:0 "DefaultFileSystem"="FATFS" "PartitionDriver"="mspart.dll" "MountAsRom"=dword:1 "MountAsRoot"=dword:1 "MountAsBootable"=dword:1 "MountPermanent"=dword:0 "Flags"=dword:00080064 Tag: File System in Wince 5... Tag: 112289
  - 16
    - USB Wireless Network Adapters for WinCE? I am currently trying to added wireless support to an existing WinCE OS image. I have added the components to my OS image to support Wi-Fi in Platform builder. I need help trying to find a compatible USB wireless network device that works with WinCE 5.0. My current WinCE OS image is working with the RNDIS USB driver, and I have read the previous posts on the USR5421 Wireless MAXg USB Adapter that is RNDIS complient. The problem is that I don't won't to limit the my customer to using only one type of USB Wireless Network manufacture. Does anyone have a list of USB wireless network devices that is compatible with WinCE 5.0? Tag: File System in Wince 5... Tag: 112286
  - 17
    - running Microsoft Device Emulator from "Device Emulator Manager" I used PB 5.0 to build an emulator using Microsoft Device Emulator, then I built the SDK. Now I am trying to run it from "Device Emulator Manager" in Visual Studio, I can see it - but its more like a category - the devices I can click are sub items in the category "Pocket PC 2003" for example, but I cannot right click on it to connect. Please help, thanks patrick Tag: File System in Wince 5... Tag: 112283
  - 18
    - ndis miniport wakeup filter Hi everybody, is there any way to control the wakeup packet filter ? Currently my miniport receives a OID_PNP_ADD_WAKE_UP_PATTERN with a filter pattern. I don't know where it comes from; I presume from protocol driver. I would like to configure or explicity send my specific wakeup packet filter. Best regards, PaoloC Tag: File System in Wince 5... Tag: 112280
  - 19
    - CreateEvent and SetEvent in WinCE6.0 Hi, I am a newbie to Windows Embedded CE. Try to understand Embedded :) I have a wince 5.0 based Application which creates a unnamed event and sends an IOCTL to driver. Upon completion of requested IO, driver uses setevent on event handle passed by APP. The whole thing works fine on WinCE 5.0 Now I have this driver in wince6.0 for a different platform, when i run the APP (built using wince 5.0), i see exception "Abort data" in driver (setevent, driver built using wince 6.0) using unnamed events is not allowed in WinCE6.0? If so, is there a work around for this instead of using named events? Any information on this would be of great help --Thanks in advance Vikranth Tag: File System in Wince 5... Tag: 112272
  - 20
    - DDKReg_GetWindowInfo() returns ERROR_INVALID_PARAMETER Hi all, I have written a simple device driver that is loaded at boot time. The driver needs to read MemBase and MemLen from the registry when initialised. I use the pointer that I receive in XXX_Init( PVOID Context) to open the device key ( hnd = OpenDeviceKey( (LPCTSTR)Context ); ) and that seems to work. However, when I call DDKReg_GetWindowinfo() with the returned handle it returns ERROR_INVALID_PARAMETER. According to MSDN this "Indicates a problem with the populated DDKWINDOWINFO structure." What does this mean? My registry entry looks like this: [HKEY_LOCAL_MACHINE\Drivers\BuiltIn\GDU] "MemBase"=dword:40100000 "MemLen"=dword:40 "Prefix"="GDU" "Dll"="gdudev.dll" "Order"=dword:22 Any ideas are much appreciated. Thanks, Rickard Tag: File System in Wince 5... Tag: 112271
  - 21
    - Wi-Fi Authentication Test... hi! I was checking the wifi authentication test.(I am using WinCE 6.0) Here when i checked the Prerequisites for authentication tests, it requires. Tux.exe kato.dll Authmatrix.dll Enroll.exe Netall.dll Apcontrol.exe I am able to find every thing except Apcontrol.exe Can any one say where i can find this application. Thanks. Tag: File System in Wince 5... Tag: 112270
  - 22
    - Ethernet Throughput Too Slow for Wince 5.0 I am running wince 5.0 with an AMD AU1100 processor running at 396MHz. I am integrating a RTL8305SC ethernet switch within the hardware platform. I am currently getting around 16.5 Mbps throughput uploading a 40Meg file to a server, and 23.5Mbps downloading a file from a server. This seems extremely slow for WinCE 5.0. On the desktop I can get almost 80% of the 100MBps link speed. Is the ndis.dll driver at a low priority such that it is not able to buffer up packets and send them out faster than the current rate I am experiencing? How can I speed up the throughput? Tag: File System in Wince 5... Tag: 112250
  - 23
    - WLAN sample code Hi all, Is any WLAN Driver Sample code is available on net? or any body know from where i take reference for WLAN Driver. I am using Wireless CF card on WINCE 5.0. I required sample code for that. So please if any body know then help us. Thanks in advance Swapnil Tag: File System in Wince 5... Tag: 112244
  - 24
    - How to strip down image of headless device (no display)? Hi, I would like to get rid of many unneeded components for a headless device. However, I cannot uncheck many catalog items because the Platform Builder thinks it is needed. For example: how can I get rid of the Tahoma fonts? Is there any method for this or do I have to apply brute force such as modifying common.bib? Thank you, Peter Tag: File System in Wince 5... Tag: 112241
  - 25
    - ConnMgrRegisterForStatusChangeNotification - #include <connmgr_status.h> problem Hi all, I have subroject where I would like to use "ConnMgrRegisterForStatusChangeNotification" which is declared in connmgr_status.h (according to MSDN). Ther is no such file in WINCE600 folder structure. None of files contains declaration of "ConnMgrRegisterForStatusChangeNotification". I see that it is delay loaded from cellcore.dll (public\cellcore\simtkit\dllload.cpp). I have checked cellcore.dll (ARM emulator build) (using dependancy walker - depend.exe) but it does not export "ConnMgrRegisterForStatusChangeNotification" function. I have installed "Shared source, ARMV4I and X86" OS. Subproject build fails with error: Error 6 fatal error C1083: Cannot open include file: 'connmgr_status.h': No such file or directory. How to use it in WinCE 6? Zdenko Tag: File System in Wince 5... Tag: 112234

Hi all
I am developing SD host driver , the driver will unload and reload client
driver when system resume.
Now I get a problem, that is while copy a file from SD card/flash to
flash/SD card, then suspend and resume the system , the copy progress is not
smooth, the progress will halt a few seconds(about 8s) , then continue
copying.
How can I do to smooth it ?
Should I set up or miss something ?

BR
Jack

Top