320 x 200

Hi All,

Here a problem with the resolution of the targetPC. After
loading the CEPC image on PIII system it only works in 320
x 200 mode. No mather what is been changed in the LOADPC
(resolution), it always turns to 320 x 200. What can I do?

Thanks a lot and best regards,

Gary
Wed Sep 24 12:56:47 CDT 2003

320x200 is the resolution if you use the /D option with LoadCEPC.

You'll want to use a /l: option instead and specify the resolution you'd
like.

The LoadCEPC display option only works if you're using the Flat or RFlat
display driver.

Also, you should run the VesaTest option and verify that your display card
supports VESA 2.0.

Gary Daniels
Windows CE Graphics test

This posting is provided "AS IS" with no warranties, and confers no rights.

"Xa4" <xavier.vangoethem@getronics.com> wrote in message
news:150f01c3827d$6f724af0$a401280a@phx.gbl...
> Hi All,
>
> Here a problem with the resolution of the targetPC. After
> loading the CEPC image on PIII system it only works in 320
> x 200 mode. No mather what is been changed in the LOADPC
> (resolution), it always turns to 320 x 200. What can I do?
>
> Thanks a lot and best regards,

Jeff
Wed Sep 24 13:25:12 CDT 2003

You should run VESATEST on the CEPC boot disk and see what resolutions are
supported by your video card. Make sure that the resolution you're trying
to load is supported. Also, if you're using CE 4.0 or later, make sure
you're using the /L option and not the /D option.

--
Jeff Sirois
Windows CE Graphics

This posting is provided "AS IS" with no warranties, and confers no rights.

"Xa4" <xavier.vangoethem@getronics.com> wrote in message
news:150f01c3827d$6f724af0$a401280a@phx.gbl...
> Hi All,
>
> Here a problem with the resolution of the targetPC. After
> loading the CEPC image on PIII system it only works in 320
> x 200 mode. No mather what is been changed in the LOADPC
> (resolution), it always turns to 320 x 200. What can I do?
>
> Thanks a lot and best regards,

frank
Tue Sep 30 15:24:32 CDT 2003

I was having the same problem. I was using an aTI Rage 3-d
and ATI Rage II. It would always be 320x240. Except for
1024x768x8. The acrd said it could do other modes but
would only go into 320x240. I then switched to another
card and I can change into other video modes.

>-----Original Message-----
>320x200 is the resolution if you use the /D option with
LoadCEPC.
>
>You'll want to use a /l: option instead and specify the
resolution you'd
>like.
>
>The LoadCEPC display option only works if you're using
the Flat or RFlat
>display driver.
>
>Also, you should run the VesaTest option and verify that
your display card
>supports VESA 2.0.
>
>Gary Daniels
>Windows CE Graphics test
>
>This posting is provided "AS IS" with no warranties, and
confers no rights.
>
>"Xa4" <xavier.vangoethem@getronics.com> wrote in message
>news:150f01c3827d$6f724af0$a401280a@phx.gbl...
>> Hi All,
>>
>> Here a problem with the resolution of the targetPC.
After
>> loading the CEPC image on PIII system it only works in
320
>> x 200 mode. No mather what is been changed in the LOADPC
>> (resolution), it always turns to 320 x 200. What can I
do?
>>
>> Thanks a lot and best regards,
>
>
>.
>